diff mbox

[3/3] exynos5250: Add arndale board support

Message ID 1364290670-7443-4-git-send-email-inderpal.singh@linaro.org
State New
Headers show

Commit Message

Inderpal Singh March 26, 2013, 9:37 a.m. UTC
Arndale board is based on samsung's exynos5250 soc.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
---
 MAINTAINERS                              |    4 +
 board/samsung/arndale/Makefile           |   54 +++
 board/samsung/arndale/arndale.c          |  117 ++++++
 board/samsung/arndale/arndale_spl.c      |   66 +++
 board/samsung/arndale/clock_init.c       |  655 ++++++++++++++++++++++++++++++
 board/samsung/arndale/clock_init.h       |  149 +++++++
 board/samsung/arndale/dmc_common.c       |  199 +++++++++
 board/samsung/arndale/dmc_init_ddr3.c    |  228 +++++++++++
 board/samsung/arndale/lowlevel_init.S    |   92 +++++
 board/samsung/arndale/setup.h            |  569 ++++++++++++++++++++++++++
 board/samsung/dts/exynos5250-arndale.dts |   36 ++
 boards.cfg                               |    1 +
 include/configs/arndale.h                |   39 ++
 tools/Makefile                           |    2 +
 14 files changed, 2211 insertions(+)
 create mode 100644 board/samsung/arndale/Makefile
 create mode 100644 board/samsung/arndale/arndale.c
 create mode 100644 board/samsung/arndale/arndale_spl.c
 create mode 100644 board/samsung/arndale/clock_init.c
 create mode 100644 board/samsung/arndale/clock_init.h
 create mode 100644 board/samsung/arndale/dmc_common.c
 create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
 create mode 100644 board/samsung/arndale/lowlevel_init.S
 create mode 100644 board/samsung/arndale/setup.h
 create mode 100644 board/samsung/dts/exynos5250-arndale.dts
 create mode 100644 include/configs/arndale.h

Comments

Rajeshwari Birje March 26, 2013, 11:16 a.m. UTC | #1
Hi Inderpal Sigh,

Most of the files added here are same as in SMDK5250, then can't we
use the same code instead of adding a new folder?

Regards,
Rajeshwari Shinde.

On Tue, Mar 26, 2013 at 3:07 PM, Inderpal Singh
<inderpal.singh@linaro.org> wrote:
> Arndale board is based on samsung's exynos5250 soc.
>
> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
> ---
>  MAINTAINERS                              |    4 +
>  board/samsung/arndale/Makefile           |   54 +++
>  board/samsung/arndale/arndale.c          |  117 ++++++
>  board/samsung/arndale/arndale_spl.c      |   66 +++
>  board/samsung/arndale/clock_init.c       |  655 ++++++++++++++++++++++++++++++
>  board/samsung/arndale/clock_init.h       |  149 +++++++
>  board/samsung/arndale/dmc_common.c       |  199 +++++++++
>  board/samsung/arndale/dmc_init_ddr3.c    |  228 +++++++++++
>  board/samsung/arndale/lowlevel_init.S    |   92 +++++
>  board/samsung/arndale/setup.h            |  569 ++++++++++++++++++++++++++
>  board/samsung/dts/exynos5250-arndale.dts |   36 ++
>  boards.cfg                               |    1 +
>  include/configs/arndale.h                |   39 ++
>  tools/Makefile                           |    2 +
>  14 files changed, 2211 insertions(+)
>  create mode 100644 board/samsung/arndale/Makefile
>  create mode 100644 board/samsung/arndale/arndale.c
>  create mode 100644 board/samsung/arndale/arndale_spl.c
>  create mode 100644 board/samsung/arndale/clock_init.c
>  create mode 100644 board/samsung/arndale/clock_init.h
>  create mode 100644 board/samsung/arndale/dmc_common.c
>  create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
>  create mode 100644 board/samsung/arndale/lowlevel_init.S
>  create mode 100644 board/samsung/arndale/setup.h
>  create mode 100644 board/samsung/dts/exynos5250-arndale.dts
>  create mode 100644 include/configs/arndale.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f6723ef..b112581 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -736,6 +736,10 @@ Chander Kashyap <k.chander@samsung.com>
>         SMDKV310                ARM ARMV7 (EXYNOS4210 SoC)
>         SMDK5250                ARM ARMV7 (EXYNOS5250 SoC)
>
> +Inderpal Singh <inderpal.singh@linaro.org>
> +
> +       Arndale                 ARM ARMV7 (EXYNOS5250 SoC)
> +
>  Lukasz Majewski <l.majewski@samsung.com>
>
>         trats                   ARM ARMV7 (EXYNOS4210 SoC)
> diff --git a/board/samsung/arndale/Makefile b/board/samsung/arndale/Makefile
> new file mode 100644
> index 0000000..f65d111
> --- /dev/null
> +++ b/board/samsung/arndale/Makefile
> @@ -0,0 +1,54 @@
> +#
> +# Copyright (C) 2013 Samsung Electronics
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB    = $(obj)lib$(BOARD).o
> +
> +SOBJS  := lowlevel_init.o
> +
> +COBJS  := clock_init.o
> +COBJS  += dmc_common.o dmc_init_ddr3.o
> +COBJS  += arndale_spl.o
> +
> +ifndef CONFIG_SPL_BUILD
> +COBJS  += arndale.o
> +endif
> +
> +SRCS   := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS   := $(addprefix $(obj),$(COBJS) $(SOBJS))
> +
> +ALL    :=       $(obj).depend $(LIB)
> +
> +all:   $(ALL)
> +
> +$(LIB):        $(OBJS)
> +       $(call cmd_link_o_target, $(OBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
> new file mode 100644
> index 0000000..7f8a568
> --- /dev/null
> +++ b/board/samsung/arndale/arndale.c
> @@ -0,0 +1,117 @@
> +/*
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <asm/arch/pinmux.h>
> +#include <asm/arch/dwmmc.h>
> +#include <asm/arch/power.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_init(void)
> +{
> +       gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
> +       return 0;
> +}
> +
> +int dram_init(void)
> +{
> +       int i;
> +       u32 addr;
> +
> +       for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> +               addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
> +               gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
> +       }
> +       return 0;
> +}
> +
> +int power_init_board(void)
> +{
> +       set_ps_hold_ctrl();
> +       return 0;
> +}
> +
> +void dram_init_banksize(void)
> +{
> +       int i;
> +       u32 addr, size;
> +
> +       for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> +               addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
> +               size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
> +
> +               gd->bd->bi_dram[i].start = addr;
> +               gd->bd->bi_dram[i].size = size;
> +       }
> +}
> +
> +#ifdef CONFIG_GENERIC_MMC
> +int board_mmc_init(bd_t *bis)
> +{
> +       int ret;
> +       /* dwmmc initializattion for available channels */
> +       ret = exynos_dwmmc_init(gd->fdt_blob);
> +       if (ret)
> +               debug("dwmmc init failed\n");
> +
> +       return ret;
> +}
> +#endif
> +
> +static int board_uart_init(void)
> +{
> +       int err, uart_id, ret = 0;
> +
> +       for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
> +               err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
> +               if (err) {
> +                       debug("UART%d not configured\n",
> +                                        (uart_id - PERIPH_ID_UART0));
> +                       ret |= err;
> +               }
> +       }
> +       return ret;
> +}
> +
> +#ifdef CONFIG_BOARD_EARLY_INIT_F
> +int board_early_init_f(void)
> +{
> +       int err;
> +       err = board_uart_init();
> +       if (err) {
> +               debug("UART init failed\n");
> +               return err;
> +       }
> +       return err;
> +}
> +#endif
> +
> +#ifdef CONFIG_DISPLAY_BOARDINFO
> +int checkboard(void)
> +{
> +       printf("\nBoard: Arndale\n");
> +
> +       return 0;
> +}
> +#endif
> +
> diff --git a/board/samsung/arndale/arndale_spl.c b/board/samsung/arndale/arndale_spl.c
> new file mode 100644
> index 0000000..8135708
> --- /dev/null
> +++ b/board/samsung/arndale/arndale_spl.c
> @@ -0,0 +1,66 @@
> +/*
> + * Copyright (c) 2012 The Chromium OS Authors.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <asm/arch/spl.h>
> +
> +#define SIGNATURE      0xdeadbeef
> +
> +/* Parameters of early board initialization in SPL */
> +static struct spl_machine_param machine_param
> +               __attribute__((section(".machine_param"))) = {
> +       .signature      = SIGNATURE,
> +       .version        = 1,
> +       .params         = "vmubfasirM",
> +       .size           = sizeof(machine_param),
> +
> +       .mem_iv_size    = 0x1f,
> +       .mem_type       = DDR_MODE_DDR3,
> +
> +       /*
> +        * Set uboot_size to 0x100000 bytes.
> +        *
> +        * This is an overly conservative value chosen to accommodate all
> +        * possible U-Boot image.  You are advised to set this value to a
> +        * smaller realistic size via scripts that modifies the .machine_param
> +        * section of output U-Boot image.
> +        */
> +       .uboot_size     = 0x100000,
> +
> +       .boot_source    = BOOT_MODE_OM,
> +       .frequency_mhz  = 800,
> +       .arm_freq_mhz   = 1000,
> +       .serial_base    = 0x12c30000,
> +       .i2c_base       = 0x12c60000,
> +       .mem_manuf      = MEM_MANUF_SAMSUNG,
> +};
> +
> +struct spl_machine_param *spl_get_machine_params(void)
> +{
> +       if (machine_param.signature != SIGNATURE) {
> +               /* Will hang if SIGNATURE dont match */
> +               while (1)
> +                       ;
> +       }
> +
> +       return &machine_param;
> +}
> diff --git a/board/samsung/arndale/clock_init.c b/board/samsung/arndale/clock_init.c
> new file mode 100644
> index 0000000..a9b0bbd
> --- /dev/null
> +++ b/board/samsung/arndale/clock_init.c
> @@ -0,0 +1,655 @@
> +/*
> + * Clock setup for Arndale board based on EXYNOS5
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <asm/io.h>
> +#include <asm/arch/clk.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/spl.h>
> +
> +#include "clock_init.h"
> +#include "setup.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +struct arm_clk_ratios arm_clk_ratios[] = {
> +       {
> +               .arm_freq_mhz = 600,
> +
> +               .apll_mdiv = 0xc8,
> +               .apll_pdiv = 0x4,
> +               .apll_sdiv = 0x1,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x1,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x2,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x1,
> +               .arm_ratio = 0x0,
> +       }, {
> +               .arm_freq_mhz = 800,
> +
> +               .apll_mdiv = 0x64,
> +               .apll_pdiv = 0x3,
> +               .apll_sdiv = 0x0,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x1,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x3,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x2,
> +               .arm_ratio = 0x0,
> +       }, {
> +               .arm_freq_mhz = 1000,
> +
> +               .apll_mdiv = 0x7d,
> +               .apll_pdiv = 0x3,
> +               .apll_sdiv = 0x0,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x1,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x4,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x2,
> +               .arm_ratio = 0x0,
> +       }, {
> +               .arm_freq_mhz = 1200,
> +
> +               .apll_mdiv = 0x96,
> +               .apll_pdiv = 0x3,
> +               .apll_sdiv = 0x0,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x3,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x5,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x3,
> +               .arm_ratio = 0x0,
> +       }, {
> +               .arm_freq_mhz = 1400,
> +
> +               .apll_mdiv = 0xaf,
> +               .apll_pdiv = 0x3,
> +               .apll_sdiv = 0x0,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x3,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x6,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x3,
> +               .arm_ratio = 0x0,
> +       }, {
> +               .arm_freq_mhz = 1700,
> +
> +               .apll_mdiv = 0x1a9,
> +               .apll_pdiv = 0x6,
> +               .apll_sdiv = 0x0,
> +
> +               .arm2_ratio = 0x0,
> +               .apll_ratio = 0x3,
> +               .pclk_dbg_ratio = 0x1,
> +               .atb_ratio = 0x6,
> +               .periph_ratio = 0x7,
> +               .acp_ratio = 0x7,
> +               .cpud_ratio = 0x3,
> +               .arm_ratio = 0x0,
> +       }
> +};
> +struct mem_timings mem_timings[] = {
> +       {
> +               .mem_manuf = MEM_MANUF_ELPIDA,
> +               .mem_type = DDR_MODE_DDR3,
> +               .frequency_mhz = 800,
> +               .mpll_mdiv = 0xc8,
> +               .mpll_pdiv = 0x3,
> +               .mpll_sdiv = 0x0,
> +               .cpll_mdiv = 0xde,
> +               .cpll_pdiv = 0x4,
> +               .cpll_sdiv = 0x2,
> +               .gpll_mdiv = 0x215,
> +               .gpll_pdiv = 0xc,
> +               .gpll_sdiv = 0x1,
> +               .epll_mdiv = 0x60,
> +               .epll_pdiv = 0x3,
> +               .epll_sdiv = 0x3,
> +               .vpll_mdiv = 0x96,
> +               .vpll_pdiv = 0x3,
> +               .vpll_sdiv = 0x2,
> +
> +               .bpll_mdiv = 0x64,
> +               .bpll_pdiv = 0x3,
> +               .bpll_sdiv = 0x0,
> +               .pclk_cdrex_ratio = 0x5,
> +               .direct_cmd_msr = {
> +                       0x00020018, 0x00030000, 0x00010042, 0x00000d70
> +               },
> +               .timing_ref = 0x000000bb,
> +               .timing_row = 0x8c36650e,
> +               .timing_data = 0x3630580b,
> +               .timing_power = 0x41000a44,
> +               .phy0_dqs = 0x08080808,
> +               .phy1_dqs = 0x08080808,
> +               .phy0_dq = 0x08080808,
> +               .phy1_dq = 0x08080808,
> +               .phy0_tFS = 0x4,
> +               .phy1_tFS = 0x4,
> +               .phy0_pulld_dqs = 0xf,
> +               .phy1_pulld_dqs = 0xf,
> +
> +               .lpddr3_ctrl_phy_reset = 0x1,
> +               .ctrl_start_point = 0x10,
> +               .ctrl_inc = 0x10,
> +               .ctrl_start = 0x1,
> +               .ctrl_dll_on = 0x1,
> +               .ctrl_ref = 0x8,
> +
> +               .ctrl_force = 0x1a,
> +               .ctrl_rdlat = 0x0b,
> +               .ctrl_bstlen = 0x08,
> +
> +               .fp_resync = 0x8,
> +               .iv_size = 0x7,
> +               .dfi_init_start = 1,
> +               .aref_en = 1,
> +
> +               .rd_fetch = 0x3,
> +
> +               .zq_mode_dds = 0x7,
> +               .zq_mode_term = 0x1,
> +               .zq_mode_noterm = 0,
> +
> +               /*
> +               * Dynamic Clock: Always Running
> +               * Memory Burst length: 8
> +               * Number of chips: 1
> +               * Memory Bus width: 32 bit
> +               * Memory Type: DDR3
> +               * Additional Latancy for PLL: 0 Cycle
> +               */
> +               .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
> +                       DMC_MEMCONTROL_DPWRDN_DISABLE |
> +                       DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
> +                       DMC_MEMCONTROL_TP_DISABLE |
> +                       DMC_MEMCONTROL_DSREF_ENABLE |
> +                       DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
> +                       DMC_MEMCONTROL_MEM_TYPE_DDR3 |
> +                       DMC_MEMCONTROL_MEM_WIDTH_32BIT |
> +                       DMC_MEMCONTROL_NUM_CHIP_1 |
> +                       DMC_MEMCONTROL_BL_8 |
> +                       DMC_MEMCONTROL_PZQ_DISABLE |
> +                       DMC_MEMCONTROL_MRR_BYTE_7_0,
> +               .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
> +                       DMC_MEMCONFIGx_CHIP_COL_10 |
> +                       DMC_MEMCONFIGx_CHIP_ROW_15 |
> +                       DMC_MEMCONFIGx_CHIP_BANK_8,
> +               .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
> +               .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
> +               .prechconfig_tp_cnt = 0xff,
> +               .dpwrdn_cyc = 0xff,
> +               .dsref_cyc = 0xffff,
> +               .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
> +                       DMC_CONCONTROL_TIMEOUT_LEVEL0 |
> +                       DMC_CONCONTROL_RD_FETCH_DISABLE |
> +                       DMC_CONCONTROL_EMPTY_DISABLE |
> +                       DMC_CONCONTROL_AREF_EN_DISABLE |
> +                       DMC_CONCONTROL_IO_PD_CON_DISABLE,
> +               .dmc_channels = 2,
> +               .chips_per_channel = 2,
> +               .chips_to_configure = 1,
> +               .send_zq_init = 1,
> +               .impedance = IMP_OUTPUT_DRV_30_OHM,
> +               .gate_leveling_enable = 0,
> +       }, {
> +               .mem_manuf = MEM_MANUF_SAMSUNG,
> +               .mem_type = DDR_MODE_DDR3,
> +               .frequency_mhz = 800,
> +               .mpll_mdiv = 0xc8,
> +               .mpll_pdiv = 0x3,
> +               .mpll_sdiv = 0x0,
> +               .cpll_mdiv = 0xde,
> +               .cpll_pdiv = 0x4,
> +               .cpll_sdiv = 0x2,
> +               .gpll_mdiv = 0x215,
> +               .gpll_pdiv = 0xc,
> +               .gpll_sdiv = 0x1,
> +               .epll_mdiv = 0x60,
> +               .epll_pdiv = 0x3,
> +               .epll_sdiv = 0x3,
> +               .vpll_mdiv = 0x96,
> +               .vpll_pdiv = 0x3,
> +               .vpll_sdiv = 0x2,
> +
> +               .bpll_mdiv = 0x64,
> +               .bpll_pdiv = 0x3,
> +               .bpll_sdiv = 0x0,
> +               .pclk_cdrex_ratio = 0x5,
> +               .direct_cmd_msr = {
> +                       0x00020018, 0x00030000, 0x00010000, 0x00000d70
> +               },
> +               .timing_ref = 0x000000bb,
> +               .timing_row = 0x8c36650e,
> +               .timing_data = 0x3630580b,
> +               .timing_power = 0x41000a44,
> +               .phy0_dqs = 0x08080808,
> +               .phy1_dqs = 0x08080808,
> +               .phy0_dq = 0x08080808,
> +               .phy1_dq = 0x08080808,
> +               .phy0_tFS = 0x8,
> +               .phy1_tFS = 0x8,
> +               .phy0_pulld_dqs = 0xf,
> +               .phy1_pulld_dqs = 0xf,
> +
> +               .lpddr3_ctrl_phy_reset = 0x1,
> +               .ctrl_start_point = 0x10,
> +               .ctrl_inc = 0x10,
> +               .ctrl_start = 0x1,
> +               .ctrl_dll_on = 0x1,
> +               .ctrl_ref = 0x8,
> +
> +               .ctrl_force = 0x1a,
> +               .ctrl_rdlat = 0x0b,
> +               .ctrl_bstlen = 0x08,
> +
> +               .fp_resync = 0x8,
> +               .iv_size = 0x7,
> +               .dfi_init_start = 1,
> +               .aref_en = 1,
> +
> +               .rd_fetch = 0x3,
> +
> +               .zq_mode_dds = 0x5,
> +               .zq_mode_term = 0x1,
> +               .zq_mode_noterm = 1,
> +
> +               /*
> +               * Dynamic Clock: Always Running
> +               * Memory Burst length: 8
> +               * Number of chips: 1
> +               * Memory Bus width: 32 bit
> +               * Memory Type: DDR3
> +               * Additional Latancy for PLL: 0 Cycle
> +               */
> +               .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
> +                       DMC_MEMCONTROL_DPWRDN_DISABLE |
> +                       DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
> +                       DMC_MEMCONTROL_TP_DISABLE |
> +                       DMC_MEMCONTROL_DSREF_ENABLE |
> +                       DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
> +                       DMC_MEMCONTROL_MEM_TYPE_DDR3 |
> +                       DMC_MEMCONTROL_MEM_WIDTH_32BIT |
> +                       DMC_MEMCONTROL_NUM_CHIP_1 |
> +                       DMC_MEMCONTROL_BL_8 |
> +                       DMC_MEMCONTROL_PZQ_DISABLE |
> +                       DMC_MEMCONTROL_MRR_BYTE_7_0,
> +               .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
> +                       DMC_MEMCONFIGx_CHIP_COL_10 |
> +                       DMC_MEMCONFIGx_CHIP_ROW_15 |
> +                       DMC_MEMCONFIGx_CHIP_BANK_8,
> +               .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
> +               .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
> +               .prechconfig_tp_cnt = 0xff,
> +               .dpwrdn_cyc = 0xff,
> +               .dsref_cyc = 0xffff,
> +               .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
> +                       DMC_CONCONTROL_TIMEOUT_LEVEL0 |
> +                       DMC_CONCONTROL_RD_FETCH_DISABLE |
> +                       DMC_CONCONTROL_EMPTY_DISABLE |
> +                       DMC_CONCONTROL_AREF_EN_DISABLE |
> +                       DMC_CONCONTROL_IO_PD_CON_DISABLE,
> +               .dmc_channels = 2,
> +               .chips_per_channel = 2,
> +               .chips_to_configure = 1,
> +               .send_zq_init = 1,
> +               .impedance = IMP_OUTPUT_DRV_40_OHM,
> +               .gate_leveling_enable = 1,
> +       }
> +};
> +
> +/**
> + * Get the required memory type and speed (SPL version).
> + *
> + * In SPL we have no device tree, so we use the machine parameters
> + *
> + * @param mem_type     Returns memory type
> + * @param frequency_mhz        Returns memory speed in MHz
> + * @param arm_freq     Returns ARM clock speed in MHz
> + * @param mem_manuf    Return Memory Manufacturer name
> + * @return 0 if all ok
> + */
> +static int clock_get_mem_selection(enum ddr_mode *mem_type,
> +               unsigned *frequency_mhz, unsigned *arm_freq,
> +               enum mem_manuf *mem_manuf)
> +{
> +       struct spl_machine_param *params;
> +
> +       params = spl_get_machine_params();
> +       *mem_type = params->mem_type;
> +       *frequency_mhz = params->frequency_mhz;
> +       *arm_freq = params->arm_freq_mhz;
> +       *mem_manuf = params->mem_manuf;
> +
> +       return 0;
> +}
> +
> +/* Get the ratios for setting ARM clock */
> +struct arm_clk_ratios *get_arm_ratios(void)
> +{
> +       struct arm_clk_ratios *arm_ratio;
> +       enum ddr_mode mem_type;
> +       enum mem_manuf mem_manuf;
> +       unsigned frequency_mhz, arm_freq;
> +       int i;
> +
> +       if (clock_get_mem_selection(&mem_type, &frequency_mhz,
> +                                       &arm_freq, &mem_manuf))
> +               ;
> +       for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
> +               i++, arm_ratio++) {
> +               if (arm_ratio->arm_freq_mhz == arm_freq)
> +                       return arm_ratio;
> +       }
> +
> +       /* will hang if failed to find clock ratio */
> +       while (1)
> +               ;
> +
> +       return NULL;
> +}
> +
> +struct mem_timings *clock_get_mem_timings(void)
> +{
> +       struct mem_timings *mem;
> +       enum ddr_mode mem_type;
> +       enum mem_manuf mem_manuf;
> +       unsigned frequency_mhz, arm_freq;
> +       int i;
> +
> +       if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
> +                                               &arm_freq, &mem_manuf)) {
> +               for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
> +                               i++, mem++) {
> +                       if (mem->mem_type == mem_type &&
> +                                       mem->frequency_mhz == frequency_mhz &&
> +                                       mem->mem_manuf == mem_manuf)
> +                               return mem;
> +               }
> +       }
> +
> +       /* will hang if failed to find memory timings */
> +       while (1)
> +               ;
> +
> +       return NULL;
> +}
> +
> +void system_clock_init()
> +{
> +       struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
> +       struct mem_timings *mem;
> +       struct arm_clk_ratios *arm_clk_ratio;
> +       u32 val, tmp;
> +
> +       mem = clock_get_mem_timings();
> +       arm_clk_ratio = get_arm_ratios();
> +
> +       clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
> +       do {
> +               val = readl(&clk->mux_stat_cpu);
> +       } while ((val | MUX_APLL_SEL_MASK) != val);
> +
> +       clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
> +       do {
> +               val = readl(&clk->mux_stat_core1);
> +       } while ((val | MUX_MPLL_SEL_MASK) != val);
> +
> +       clrbits_le32(&clk->src_core1, MUX_CPLL_SEL_MASK);
> +       clrbits_le32(&clk->src_core1, MUX_EPLL_SEL_MASK);
> +       clrbits_le32(&clk->src_core1, MUX_VPLL_SEL_MASK);
> +       clrbits_le32(&clk->src_core1, MUX_GPLL_SEL_MASK);
> +       tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
> +               | MUX_GPLL_SEL_MASK;
> +       do {
> +               val = readl(&clk->mux_stat_top2);
> +       } while ((val | tmp) != val);
> +
> +       clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
> +       do {
> +               val = readl(&clk->mux_stat_cdrex);
> +       } while ((val | MUX_BPLL_SEL_MASK) != val);
> +
> +       /* PLL locktime */
> +       writel(APLL_LOCK_VAL, &clk->apll_lock);
> +
> +       writel(MPLL_LOCK_VAL, &clk->mpll_lock);
> +
> +       writel(BPLL_LOCK_VAL, &clk->bpll_lock);
> +
> +       writel(CPLL_LOCK_VAL, &clk->cpll_lock);
> +
> +       writel(GPLL_LOCK_VAL, &clk->gpll_lock);
> +
> +       writel(EPLL_LOCK_VAL, &clk->epll_lock);
> +
> +       writel(VPLL_LOCK_VAL, &clk->vpll_lock);
> +
> +       writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
> +
> +       writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
> +       do {
> +               val = readl(&clk->mux_stat_cpu);
> +       } while ((val | HPM_SEL_SCLK_MPLL) != val);
> +
> +       val = arm_clk_ratio->arm2_ratio << 28
> +               | arm_clk_ratio->apll_ratio << 24
> +               | arm_clk_ratio->pclk_dbg_ratio << 20
> +               | arm_clk_ratio->atb_ratio << 16
> +               | arm_clk_ratio->periph_ratio << 12
> +               | arm_clk_ratio->acp_ratio << 8
> +               | arm_clk_ratio->cpud_ratio << 4
> +               | arm_clk_ratio->arm_ratio;
> +       writel(val, &clk->div_cpu0);
> +       do {
> +               val = readl(&clk->div_stat_cpu0);
> +       } while (0 != val);
> +
> +       writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
> +       do {
> +               val = readl(&clk->div_stat_cpu1);
> +       } while (0 != val);
> +
> +       /* Set APLL */
> +       writel(APLL_CON1_VAL, &clk->apll_con1);
> +       val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
> +                       arm_clk_ratio->apll_sdiv);
> +       writel(val, &clk->apll_con0);
> +       while (readl(&clk->apll_con0) & APLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set MPLL */
> +       writel(MPLL_CON1_VAL, &clk->mpll_con1);
> +       val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
> +       writel(val, &clk->mpll_con0);
> +       while (readl(&clk->mpll_con0) & MPLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set BPLL */
> +       writel(BPLL_CON1_VAL, &clk->bpll_con1);
> +       val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
> +       writel(val, &clk->bpll_con0);
> +       while (readl(&clk->bpll_con0) & BPLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set CPLL */
> +       writel(CPLL_CON1_VAL, &clk->cpll_con1);
> +       val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
> +       writel(val, &clk->cpll_con0);
> +       while (readl(&clk->cpll_con0) & CPLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set GPLL */
> +       writel(GPLL_CON1_VAL, &clk->gpll_con1);
> +       val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
> +       writel(val, &clk->gpll_con0);
> +       while (readl(&clk->gpll_con0) & GPLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set EPLL */
> +       writel(EPLL_CON2_VAL, &clk->epll_con2);
> +       writel(EPLL_CON1_VAL, &clk->epll_con1);
> +       val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
> +       writel(val, &clk->epll_con0);
> +       while (readl(&clk->epll_con0) & EPLL_CON0_LOCKED)
> +               ;
> +
> +       /* Set VPLL */
> +       writel(VPLL_CON2_VAL, &clk->vpll_con2);
> +       writel(VPLL_CON1_VAL, &clk->vpll_con1);
> +       val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
> +       writel(val, &clk->vpll_con0);
> +       while (readl(&clk->vpll_con0) & VPLL_CON0_LOCKED)
> +               ;
> +
> +       writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
> +       writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
> +       while (readl(&clk->div_stat_core0) != 0)
> +               ;
> +
> +       writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
> +       while (readl(&clk->div_stat_core1) != 0)
> +               ;
> +
> +       writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
> +       while (readl(&clk->div_stat_sysrgt) != 0)
> +               ;
> +
> +       writel(CLK_DIV_ACP_VAL, &clk->div_acp);
> +       while (readl(&clk->div_stat_acp) != 0)
> +               ;
> +
> +       writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
> +       while (readl(&clk->div_stat_syslft) != 0)
> +               ;
> +
> +       writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
> +       writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
> +       writel(TOP2_VAL, &clk->src_top2);
> +       writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
> +
> +       writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
> +       while (readl(&clk->div_stat_top0))
> +               ;
> +
> +       writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
> +       while (readl(&clk->div_stat_top1))
> +               ;
> +
> +       writel(CLK_SRC_LEX_VAL, &clk->src_lex);
> +       while (1) {
> +               val = readl(&clk->mux_stat_lex);
> +               if (val == (val | 1))
> +                       break;
> +       }
> +
> +       writel(CLK_DIV_LEX_VAL, &clk->div_lex);
> +       while (readl(&clk->div_stat_lex))
> +               ;
> +
> +       writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
> +       while (readl(&clk->div_stat_r0x))
> +               ;
> +
> +       writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
> +       while (readl(&clk->div_stat_r0x))
> +               ;
> +
> +       writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
> +       while (readl(&clk->div_stat_r1x))
> +               ;
> +
> +       writel(CLK_REG_DISABLE, &clk->src_cdrex);
> +
> +       writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
> +       while (readl(&clk->div_stat_cdrex))
> +               ;
> +
> +       val = readl(&clk->src_cpu);
> +       val |= CLK_SRC_CPU_VAL;
> +       writel(val, &clk->src_cpu);
> +
> +       val = readl(&clk->src_top2);
> +       val |= CLK_SRC_TOP2_VAL;
> +       writel(val, &clk->src_top2);
> +
> +       val = readl(&clk->src_core1);
> +       val |= CLK_SRC_CORE1_VAL;
> +       writel(val, &clk->src_core1);
> +
> +       writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
> +       writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
> +       while (readl(&clk->div_stat_fsys0))
> +               ;
> +
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
> +
> +       writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
> +       writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
> +
> +       writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
> +       writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
> +       writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
> +       writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
> +
> +       writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
> +       writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
> +       writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
> +       writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
> +       writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
> +
> +       /* FIMD1 SRC CLK SELECTION */
> +       writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
> +
> +       val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
> +               | MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
> +               | MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
> +               | MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
> +       writel(val, &clk->div_fsys2);
> +}
> diff --git a/board/samsung/arndale/clock_init.h b/board/samsung/arndale/clock_init.h
> new file mode 100644
> index 0000000..5d01a6c
> --- /dev/null
> +++ b/board/samsung/arndale/clock_init.h
> @@ -0,0 +1,149 @@
> +/*
> + * Clock initialization routines
> + *
> + * Copyright (c) 2011 The Chromium OS Authors.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __ARNDALE_CLOCK_INIT_H
> +#define __ARNDALE_CLOCK_INIT_H
> +
> +enum {
> +       MEM_TIMINGS_MSR_COUNT   = 4,
> +};
> +
> +/* These are the ratio's for configuring ARM clock */
> +struct arm_clk_ratios {
> +       unsigned arm_freq_mhz;          /* Frequency of ARM core in MHz */
> +
> +       unsigned apll_mdiv;
> +       unsigned apll_pdiv;
> +       unsigned apll_sdiv;
> +
> +       unsigned arm2_ratio;
> +       unsigned apll_ratio;
> +       unsigned pclk_dbg_ratio;
> +       unsigned atb_ratio;
> +       unsigned periph_ratio;
> +       unsigned acp_ratio;
> +       unsigned cpud_ratio;
> +       unsigned arm_ratio;
> +};
> +
> +/* These are the memory timings for a particular memory type and speed */
> +struct mem_timings {
> +       enum mem_manuf mem_manuf;       /* Memory manufacturer */
> +       enum ddr_mode mem_type;         /* Memory type */
> +       unsigned frequency_mhz;         /* Frequency of memory in MHz */
> +
> +       /* Here follow the timing parameters for the selected memory */
> +       unsigned apll_mdiv;
> +       unsigned apll_pdiv;
> +       unsigned apll_sdiv;
> +       unsigned mpll_mdiv;
> +       unsigned mpll_pdiv;
> +       unsigned mpll_sdiv;
> +       unsigned cpll_mdiv;
> +       unsigned cpll_pdiv;
> +       unsigned cpll_sdiv;
> +       unsigned gpll_mdiv;
> +       unsigned gpll_pdiv;
> +       unsigned gpll_sdiv;
> +       unsigned epll_mdiv;
> +       unsigned epll_pdiv;
> +       unsigned epll_sdiv;
> +       unsigned vpll_mdiv;
> +       unsigned vpll_pdiv;
> +       unsigned vpll_sdiv;
> +       unsigned bpll_mdiv;
> +       unsigned bpll_pdiv;
> +       unsigned bpll_sdiv;
> +       unsigned pclk_cdrex_ratio;
> +       unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
> +
> +       unsigned timing_ref;
> +       unsigned timing_row;
> +       unsigned timing_data;
> +       unsigned timing_power;
> +
> +       /* DQS, DQ, DEBUG offsets */
> +       unsigned phy0_dqs;
> +       unsigned phy1_dqs;
> +       unsigned phy0_dq;
> +       unsigned phy1_dq;
> +       unsigned phy0_tFS;
> +       unsigned phy1_tFS;
> +       unsigned phy0_pulld_dqs;
> +       unsigned phy1_pulld_dqs;
> +
> +       unsigned lpddr3_ctrl_phy_reset;
> +       unsigned ctrl_start_point;
> +       unsigned ctrl_inc;
> +       unsigned ctrl_start;
> +       unsigned ctrl_dll_on;
> +       unsigned ctrl_ref;
> +
> +       unsigned ctrl_force;
> +       unsigned ctrl_rdlat;
> +       unsigned ctrl_bstlen;
> +
> +       unsigned fp_resync;
> +       unsigned iv_size;
> +       unsigned dfi_init_start;
> +       unsigned aref_en;
> +
> +       unsigned rd_fetch;
> +
> +       unsigned zq_mode_dds;
> +       unsigned zq_mode_term;
> +       unsigned zq_mode_noterm;        /* 1 to allow termination disable */
> +
> +       unsigned memcontrol;
> +       unsigned memconfig;
> +
> +       unsigned membaseconfig0;
> +       unsigned membaseconfig1;
> +       unsigned prechconfig_tp_cnt;
> +       unsigned dpwrdn_cyc;
> +       unsigned dsref_cyc;
> +       unsigned concontrol;
> +       /* Channel and Chip Selection */
> +       uint8_t dmc_channels;           /* number of memory channels */
> +       uint8_t chips_per_channel;      /* number of chips per channel */
> +       uint8_t chips_to_configure;     /* number of chips to configure */
> +       uint8_t send_zq_init;           /* 1 to send this command */
> +       unsigned impedance;             /* drive strength impedeance */
> +       uint8_t gate_leveling_enable;   /* check gate leveling is enabled */
> +};
> +
> +/**
> + * Get the correct memory timings for our selected memory type and speed.
> + *
> + * This function can be called from SPL or the main U-Boot.
> + *
> + * @return pointer to the memory timings that we should use
> + */
> +struct mem_timings *clock_get_mem_timings(void);
> +
> +/*
> + * Initialize clock for the device
> + */
> +void system_clock_init(void);
> +#endif
> diff --git a/board/samsung/arndale/dmc_common.c b/board/samsung/arndale/dmc_common.c
> new file mode 100644
> index 0000000..5a51def
> --- /dev/null
> +++ b/board/samsung/arndale/dmc_common.c
> @@ -0,0 +1,199 @@
> +/*
> + * Mem setup common file for different types of DDR present on Arndale boards.
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <asm/arch/spl.h>
> +
> +#include "clock_init.h"
> +#include "setup.h"
> +
> +#define ZQ_INIT_TIMEOUT        10000
> +
> +int dmc_config_zq(struct mem_timings *mem,
> +                 struct exynos5_phy_control *phy0_ctrl,
> +                 struct exynos5_phy_control *phy1_ctrl)
> +{
> +       unsigned long val = 0;
> +       int i;
> +
> +       /*
> +        * ZQ Calibration:
> +        * Select Driver Strength,
> +        * long calibration for manual calibration
> +        */
> +       val = PHY_CON16_RESET_VAL;
> +       val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
> +       val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
> +       val |= ZQ_CLK_DIV_EN;
> +       writel(val, &phy0_ctrl->phy_con16);
> +       writel(val, &phy1_ctrl->phy_con16);
> +
> +       /* Disable termination */
> +       if (mem->zq_mode_noterm)
> +               val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
> +       writel(val, &phy0_ctrl->phy_con16);
> +       writel(val, &phy1_ctrl->phy_con16);
> +
> +       /* ZQ_MANUAL_START: Enable */
> +       val |= ZQ_MANUAL_STR;
> +       writel(val, &phy0_ctrl->phy_con16);
> +       writel(val, &phy1_ctrl->phy_con16);
> +
> +       /* ZQ_MANUAL_START: Disable */
> +       val &= ~ZQ_MANUAL_STR;
> +
> +       /*
> +        * Since we are manaully calibrating the ZQ values,
> +        * we are looping for the ZQ_init to complete.
> +        */
> +       i = ZQ_INIT_TIMEOUT;
> +       while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
> +               sdelay(100);
> +               i--;
> +       }
> +       if (!i)
> +               return -1;
> +       writel(val, &phy0_ctrl->phy_con16);
> +
> +       i = ZQ_INIT_TIMEOUT;
> +       while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
> +               sdelay(100);
> +               i--;
> +       }
> +       if (!i)
> +               return -1;
> +       writel(val, &phy1_ctrl->phy_con16);
> +
> +       return 0;
> +}
> +
> +void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
> +{
> +       unsigned long val;
> +
> +       if (mode == DDR_MODE_DDR3) {
> +               val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
> +               writel(val, &dmc->phycontrol0);
> +       }
> +
> +       /* Update DLL Information: Force DLL Resyncronization */
> +       val = readl(&dmc->phycontrol0);
> +       val |= FP_RSYNC;
> +       writel(val, &dmc->phycontrol0);
> +
> +       /* Reset Force DLL Resyncronization */
> +       val = readl(&dmc->phycontrol0);
> +       val &= ~FP_RSYNC;
> +       writel(val, &dmc->phycontrol0);
> +}
> +
> +void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
> +{
> +       int channel, chip;
> +
> +       for (channel = 0; channel < mem->dmc_channels; channel++) {
> +               unsigned long mask;
> +
> +               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
> +               for (chip = 0; chip < mem->chips_to_configure; chip++) {
> +                       int i;
> +
> +                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
> +
> +                       /* Sending NOP command */
> +                       writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
> +
> +                       /*
> +                        * TODO(alim.akhtar@samsung.com): Do we need these
> +                        * delays? This one and the next were not there for
> +                        * DDR3.
> +                        */
> +                       sdelay(0x10000);
> +
> +                       /* Sending EMRS/MRS commands */
> +                       for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
> +                               writel(mem->direct_cmd_msr[i] | mask,
> +                                      &dmc->directcmd);
> +                               sdelay(0x10000);
> +                       }
> +
> +                       if (mem->send_zq_init) {
> +                               /* Sending ZQINIT command */
> +                               writel(DIRECT_CMD_ZQINIT | mask,
> +                                      &dmc->directcmd);
> +
> +                               sdelay(10000);
> +                       }
> +               }
> +       }
> +}
> +
> +void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
> +{
> +       int channel, chip;
> +
> +       for (channel = 0; channel < mem->dmc_channels; channel++) {
> +               unsigned long mask;
> +
> +               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
> +               for (chip = 0; chip < mem->chips_per_channel; chip++) {
> +                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
> +
> +                       /* PALL (all banks precharge) CMD */
> +                       writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
> +                       sdelay(0x10000);
> +               }
> +       }
> +}
> +
> +void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
> +{
> +       writel(mem->memconfig, &dmc->memconfig0);
> +       writel(mem->memconfig, &dmc->memconfig1);
> +       writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
> +       writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
> +}
> +
> +void mem_ctrl_init()
> +{
> +       struct spl_machine_param *param = spl_get_machine_params();
> +       struct mem_timings *mem;
> +       int ret;
> +
> +       mem = clock_get_mem_timings();
> +
> +       /* If there are any other memory variant, add their init call below */
> +       if (param->mem_type == DDR_MODE_DDR3) {
> +               ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size);
> +               if (ret) {
> +                       /* will hang if failed to init memory control */
> +                       while (1)
> +                               ;
> +               }
> +       } else {
> +               /* will hang if unknow memory type  */
> +               while (1)
> +                       ;
> +       }
> +}
> diff --git a/board/samsung/arndale/dmc_init_ddr3.c b/board/samsung/arndale/dmc_init_ddr3.c
> new file mode 100644
> index 0000000..ce91451
> --- /dev/null
> +++ b/board/samsung/arndale/dmc_init_ddr3.c
> @@ -0,0 +1,228 @@
> +/*
> + * DDR3 mem setup file for Arndale board based on EXYNOS5
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <config.h>
> +#include <asm/io.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/dmc.h>
> +#include "setup.h"
> +#include "clock_init.h"
> +
> +#define RDLVL_COMPLETE_TIMEOUT 10000
> +
> +static void reset_phy_ctrl(void)
> +{
> +       struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
> +
> +       writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
> +       writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
> +}
> +
> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
> +{
> +       unsigned int val;
> +       struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
> +       struct exynos5_dmc *dmc;
> +       int i;
> +
> +       phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
> +       phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
> +       dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
> +
> +       reset_phy_ctrl();
> +
> +       /* Set Impedance Output Driver */
> +       val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
> +               (mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
> +               (mem->impedance << CA_CS_DRVR_DS_OFFSET) |
> +               (mem->impedance << CA_ADR_DRVR_DS_OFFSET);
> +       writel(val, &phy0_ctrl->phy_con39);
> +       writel(val, &phy1_ctrl->phy_con39);
> +
> +       /* Set Read Latency and Burst Length for PHY0 and PHY1 */
> +       val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
> +               (mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
> +       writel(val, &phy0_ctrl->phy_con42);
> +       writel(val, &phy1_ctrl->phy_con42);
> +
> +       /* ZQ Calibration */
> +       if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
> +               return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
> +
> +       /* DQ Signal */
> +       writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
> +       writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
> +
> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
> +               | (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
> +               &dmc->concontrol);
> +
> +       update_reset_dll(dmc, DDR_MODE_DDR3);
> +
> +       /* DQS Signal */
> +       writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
> +       writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
> +
> +       writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
> +       writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
> +
> +       writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
> +       writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
> +
> +       val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
> +               (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
> +               (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
> +               (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
> +       writel(val, &phy0_ctrl->phy_con12);
> +       writel(val, &phy1_ctrl->phy_con12);
> +
> +       /* Start DLL locking */
> +       writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
> +               &phy0_ctrl->phy_con12);
> +       writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
> +               &phy1_ctrl->phy_con12);
> +
> +       update_reset_dll(dmc, DDR_MODE_DDR3);
> +
> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
> +               &dmc->concontrol);
> +
> +       /* Memory Channel Inteleaving Size */
> +       writel(mem->iv_size, &dmc->ivcontrol);
> +
> +       writel(mem->memconfig, &dmc->memconfig0);
> +       writel(mem->memconfig, &dmc->memconfig1);
> +       writel(mem->membaseconfig0, &dmc->membaseconfig0);
> +       writel(mem->membaseconfig1, &dmc->membaseconfig1);
> +
> +       /* Precharge Configuration */
> +       writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
> +               &dmc->prechconfig);
> +
> +       /* Power Down mode Configuration */
> +       writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
> +               mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
> +               &dmc->pwrdnconfig);
> +
> +       /* TimingRow, TimingData, TimingPower and Timingaref
> +        * values as per Memory AC parameters
> +        */
> +       writel(mem->timing_ref, &dmc->timingref);
> +       writel(mem->timing_row, &dmc->timingrow);
> +       writel(mem->timing_data, &dmc->timingdata);
> +       writel(mem->timing_power, &dmc->timingpower);
> +
> +       /* Send PALL command */
> +       dmc_config_prech(mem, dmc);
> +
> +       /* Send NOP, MRS and ZQINIT commands */
> +       dmc_config_mrs(mem, dmc);
> +
> +       if (mem->gate_leveling_enable) {
> +               val = PHY_CON0_RESET_VAL;
> +               val |= P0_CMD_EN;
> +               writel(val, &phy0_ctrl->phy_con0);
> +               writel(val, &phy1_ctrl->phy_con0);
> +
> +               val = PHY_CON2_RESET_VAL;
> +               val |= INIT_DESKEW_EN;
> +               writel(val, &phy0_ctrl->phy_con2);
> +               writel(val, &phy1_ctrl->phy_con2);
> +
> +               val = PHY_CON0_RESET_VAL;
> +               val |= P0_CMD_EN;
> +               val |= BYTE_RDLVL_EN;
> +               writel(val, &phy0_ctrl->phy_con0);
> +               writel(val, &phy1_ctrl->phy_con0);
> +
> +               val = (mem->ctrl_start_point <<
> +                               PHY_CON12_CTRL_START_POINT_SHIFT) |
> +                       (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
> +                       (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
> +                       (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
> +                       (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
> +               writel(val, &phy0_ctrl->phy_con12);
> +               writel(val, &phy1_ctrl->phy_con12);
> +
> +               val = PHY_CON2_RESET_VAL;
> +               val |= INIT_DESKEW_EN;
> +               val |= RDLVL_GATE_EN;
> +               writel(val, &phy0_ctrl->phy_con2);
> +               writel(val, &phy1_ctrl->phy_con2);
> +
> +               val = PHY_CON0_RESET_VAL;
> +               val |= P0_CMD_EN;
> +               val |= BYTE_RDLVL_EN;
> +               val |= CTRL_SHGATE;
> +               writel(val, &phy0_ctrl->phy_con0);
> +               writel(val, &phy1_ctrl->phy_con0);
> +
> +               val = PHY_CON1_RESET_VAL;
> +               val &= ~(CTRL_GATEDURADJ_MASK);
> +               writel(val, &phy0_ctrl->phy_con1);
> +               writel(val, &phy1_ctrl->phy_con1);
> +
> +               writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
> +               i = RDLVL_COMPLETE_TIMEOUT;
> +               while ((readl(&dmc->phystatus) &
> +                       (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
> +                       (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
> +                       /*
> +                        * TODO(waihong): Comment on how long this take to
> +                        * timeout
> +                        */
> +                       sdelay(100);
> +                       i--;
> +               }
> +               if (!i)
> +                       return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
> +               writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
> +
> +               writel(0, &phy0_ctrl->phy_con14);
> +               writel(0, &phy1_ctrl->phy_con14);
> +
> +               val = (mem->ctrl_start_point <<
> +                               PHY_CON12_CTRL_START_POINT_SHIFT) |
> +                       (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
> +                       (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
> +                       (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
> +                       (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
> +                       (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
> +               writel(val, &phy0_ctrl->phy_con12);
> +               writel(val, &phy1_ctrl->phy_con12);
> +
> +               update_reset_dll(dmc, DDR_MODE_DDR3);
> +       }
> +
> +       /* Send PALL command */
> +       dmc_config_prech(mem, dmc);
> +
> +       writel(mem->memcontrol, &dmc->memcontrol);
> +
> +       /* Set DMC Concontrol and enable auto-refresh counter */
> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
> +               | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
> +       return 0;
> +}
> diff --git a/board/samsung/arndale/lowlevel_init.S b/board/samsung/arndale/lowlevel_init.S
> new file mode 100644
> index 0000000..4fa73a7
> --- /dev/null
> +++ b/board/samsung/arndale/lowlevel_init.S
> @@ -0,0 +1,92 @@
> +/*
> + * Lowlevel setup for Arndale board based on Exynos5
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <config.h>
> +#include <version.h>
> +#include <asm/arch/cpu.h>
> +
> +_TEXT_BASE:
> +       .word   CONFIG_SYS_TEXT_BASE
> +
> +       .globl lowlevel_init
> +lowlevel_init:
> +
> +       /* use iRAM stack in bl2 */
> +       ldr     sp, =CONFIG_IRAM_STACK
> +       stmdb   r13!, {ip,lr}
> +
> +       /* check reset status */
> +       ldr     r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET)
> +       ldr     r1, [r0]
> +
> +       /* AFTR wakeup reset */
> +       ldr     r2, =S5P_CHECK_DIDLE
> +       cmp     r1, r2
> +       beq     exit_wakeup
> +
> +       /* Sleep wakeup reset */
> +       ldr     r2, =S5P_CHECK_SLEEP
> +       cmp     r1, r2
> +       beq     wakeup_reset
> +
> +       /*
> +        * If U-boot is already running in RAM, no need to relocate U-Boot.
> +        * Memory controller must be configured before relocating U-Boot
> +        * in ram.
> +        */
> +       ldr     r0, =0x0ffffff          /* r0 <- Mask Bits*/
> +       bic     r1, pc, r0              /* pc <- current addr of code */
> +                                       /* r1 <- unmasked bits of pc */
> +       ldr     r2, _TEXT_BASE          /* r2 <- original base addr in ram */
> +       bic     r2, r2, r0              /* r2 <- unmasked bits of r2*/
> +       cmp     r1, r2                  /* compare r1, r2 */
> +       beq     1f                      /* r0 == r1 then skip sdram init */
> +
> +       /* init system clock */
> +       bl      system_clock_init
> +
> +       /* Memory initialize */
> +       bl      mem_ctrl_init
> +1:
> +       bl      arch_cpu_init
> +       bl      tzpc_init
> +       ldmia   r13!, {ip,pc}
> +
> +wakeup_reset:
> +       bl      system_clock_init
> +       bl      mem_ctrl_init
> +       bl      arch_cpu_init
> +       bl      tzpc_init
> +
> +exit_wakeup:
> +       /* Load return address and jump to kernel */
> +       ldr     r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET)
> +
> +       /* r1 = physical address of exynos5_cpu_resume function*/
> +       ldr     r1, [r0]
> +
> +       /* Jump to kernel */
> +       mov     pc, r1
> +       nop
> +       nop
> diff --git a/board/samsung/arndale/setup.h b/board/samsung/arndale/setup.h
> new file mode 100644
> index 0000000..f68dd75
> --- /dev/null
> +++ b/board/samsung/arndale/setup.h
> @@ -0,0 +1,569 @@
> +/*
> + * Machine Specific Values for Arndale board based on EXYNOS5
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef _ARNDALE_SETUP_H
> +#define _ARNDALE_SETUP_H
> +
> +#include <config.h>
> +#include <asm/arch/dmc.h>
> +
> +/* APLL_CON1   */
> +#define APLL_CON1_VAL  (0x00203800)
> +
> +/* MPLL_CON1   */
> +#define MPLL_CON1_VAL   (0x00203800)
> +
> +/* CPLL_CON1   */
> +#define CPLL_CON1_VAL  (0x00203800)
> +
> +/* GPLL_CON1   */
> +#define GPLL_CON1_VAL  (0x00203800)
> +
> +/* EPLL_CON1, CON2     */
> +#define EPLL_CON1_VAL  0x00000000
> +#define EPLL_CON2_VAL  0x00000080
> +
> +/* VPLL_CON1, CON2     */
> +#define VPLL_CON1_VAL  0x00000000
> +#define VPLL_CON2_VAL  0x00000080
> +
> +/* BPLL_CON1   */
> +#define BPLL_CON1_VAL  0x00203800
> +
> +/* Set PLL */
> +#define set_pll(mdiv, pdiv, sdiv)      (1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
> +
> +/* CLK_SRC_CPU */
> +/* 0 = MOUTAPLL,  1 = SCLKMPLL */
> +#define MUX_HPM_SEL             0
> +#define MUX_CPU_SEL             0
> +#define MUX_APLL_SEL            1
> +
> +#define CLK_SRC_CPU_VAL                ((MUX_HPM_SEL << 20)    \
> +                               | (MUX_CPU_SEL << 16)  \
> +                               | (MUX_APLL_SEL))
> +
> +/* MEMCONTROL register bit fields */
> +#define DMC_MEMCONTROL_CLK_STOP_DISABLE        (0 << 0)
> +#define DMC_MEMCONTROL_DPWRDN_DISABLE  (0 << 1)
> +#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
> +#define DMC_MEMCONTROL_TP_DISABLE      (0 << 4)
> +#define DMC_MEMCONTROL_DSREF_DISABLE   (0 << 5)
> +#define DMC_MEMCONTROL_DSREF_ENABLE    (1 << 5)
> +#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x)    (x << 6)
> +
> +#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3  (7 << 8)
> +#define DMC_MEMCONTROL_MEM_TYPE_DDR3    (6 << 8)
> +#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2  (5 << 8)
> +
> +#define DMC_MEMCONTROL_MEM_WIDTH_32BIT  (2 << 12)
> +
> +#define DMC_MEMCONTROL_NUM_CHIP_1       (0 << 16)
> +#define DMC_MEMCONTROL_NUM_CHIP_2       (1 << 16)
> +
> +#define DMC_MEMCONTROL_BL_8             (3 << 20)
> +#define DMC_MEMCONTROL_BL_4             (2 << 20)
> +
> +#define DMC_MEMCONTROL_PZQ_DISABLE      (0 << 24)
> +
> +#define DMC_MEMCONTROL_MRR_BYTE_7_0     (0 << 25)
> +#define DMC_MEMCONTROL_MRR_BYTE_15_8    (1 << 25)
> +#define DMC_MEMCONTROL_MRR_BYTE_23_16   (2 << 25)
> +#define DMC_MEMCONTROL_MRR_BYTE_31_24   (3 << 25)
> +
> +/* MEMCONFIG0 register bit fields */
> +#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED     (1 << 12)
> +#define DMC_MEMCONFIGx_CHIP_COL_10              (3 << 8)
> +#define DMC_MEMCONFIGx_CHIP_ROW_14              (2 << 4)
> +#define DMC_MEMCONFIGx_CHIP_ROW_15              (3 << 4)
> +#define DMC_MEMCONFIGx_CHIP_BANK_8              (3 << 0)
> +
> +#define DMC_MEMBASECONFIGx_CHIP_BASE(x)         (x << 16)
> +#define DMC_MEMBASECONFIGx_CHIP_MASK(x)         (x << 0)
> +#define DMC_MEMBASECONFIG_VAL(x)        (       \
> +       DMC_MEMBASECONFIGx_CHIP_BASE(x) |       \
> +       DMC_MEMBASECONFIGx_CHIP_MASK(0x780)     \
> +)
> +
> +#define DMC_MEMBASECONFIG0_VAL  DMC_MEMBASECONFIG_VAL(0x40)
> +#define DMC_MEMBASECONFIG1_VAL  DMC_MEMBASECONFIG_VAL(0x80)
> +
> +#define DMC_PRECHCONFIG_VAL             0xFF000000
> +#define DMC_PWRDNCONFIG_VAL             0xFFFF00FF
> +
> +#define DMC_CONCONTROL_RESET_VAL       0x0FFF0000
> +#define DFI_INIT_START         (1 << 28)
> +#define EMPTY                  (1 << 8)
> +#define AREF_EN                        (1 << 5)
> +
> +#define DFI_INIT_COMPLETE_CHO  (1 << 2)
> +#define DFI_INIT_COMPLETE_CH1  (1 << 3)
> +
> +#define RDLVL_COMPLETE_CHO     (1 << 14)
> +#define RDLVL_COMPLETE_CH1     (1 << 15)
> +
> +#define CLK_STOP_EN    (1 << 0)
> +#define DPWRDN_EN      (1 << 1)
> +#define DSREF_EN       (1 << 5)
> +
> +/* COJCONTROL register bit fields */
> +#define DMC_CONCONTROL_IO_PD_CON_DISABLE       (0 << 3)
> +#define DMC_CONCONTROL_AREF_EN_DISABLE         (0 << 5)
> +#define DMC_CONCONTROL_EMPTY_DISABLE           (0 << 8)
> +#define DMC_CONCONTROL_EMPTY_ENABLE            (1 << 8)
> +#define DMC_CONCONTROL_RD_FETCH_DISABLE                (0x0 << 12)
> +#define DMC_CONCONTROL_TIMEOUT_LEVEL0          (0xFFF << 16)
> +#define DMC_CONCONTROL_DFI_INIT_START_DISABLE  (0 << 28)
> +
> +/* CLK_DIV_CPU0_VAL */
> +#define CLK_DIV_CPU0_VAL       ((ARM2_RATIO << 28)             \
> +                               | (APLL_RATIO << 24)            \
> +                               | (PCLK_DBG_RATIO << 20)        \
> +                               | (ATB_RATIO << 16)             \
> +                               | (PERIPH_RATIO << 12)          \
> +                               | (ACP_RATIO << 8)              \
> +                               | (CPUD_RATIO << 4)             \
> +                               | (ARM_RATIO))
> +
> +
> +/* CLK_FSYS */
> +#define CLK_SRC_FSYS0_VAL              0x66666
> +#define CLK_DIV_FSYS0_VAL             0x0BB00000
> +
> +/* CLK_DIV_CPU1        */
> +#define HPM_RATIO               0x2
> +#define COPY_RATIO              0x0
> +
> +/* CLK_DIV_CPU1 = 0x00000003 */
> +#define CLK_DIV_CPU1_VAL        ((HPM_RATIO << 4)              \
> +                               | (COPY_RATIO))
> +
> +/* CLK_SRC_CORE0 */
> +#define CLK_SRC_CORE0_VAL       0x00000000
> +
> +/* CLK_SRC_CORE1 */
> +#define CLK_SRC_CORE1_VAL       0x100
> +
> +/* CLK_DIV_CORE0 */
> +#define CLK_DIV_CORE0_VAL       0x00120000
> +
> +/* CLK_DIV_CORE1 */
> +#define CLK_DIV_CORE1_VAL       0x07070700
> +
> +/* CLK_DIV_SYSRGT */
> +#define CLK_DIV_SYSRGT_VAL      0x00000111
> +
> +/* CLK_DIV_ACP */
> +#define CLK_DIV_ACP_VAL         0x12
> +
> +/* CLK_DIV_SYSLFT */
> +#define CLK_DIV_SYSLFT_VAL      0x00000311
> +
> +/* CLK_SRC_CDREX */
> +#define CLK_SRC_CDREX_VAL       0x1
> +
> +/* CLK_DIV_CDREX */
> +#define MCLK_CDREX2_RATIO       0x0
> +#define ACLK_EFCON_RATIO        0x1
> +#define MCLK_DPHY_RATIO                0x1
> +#define MCLK_CDREX_RATIO       0x1
> +#define ACLK_C2C_200_RATIO     0x1
> +#define C2C_CLK_400_RATIO      0x1
> +#define PCLK_CDREX_RATIO       0x1
> +#define ACLK_CDREX_RATIO       0x1
> +
> +#define CLK_DIV_CDREX_VAL      ((MCLK_DPHY_RATIO << 24)        \
> +                               | (C2C_CLK_400_RATIO << 6)      \
> +                               | (PCLK_CDREX_RATIO << 4)       \
> +                               | (ACLK_CDREX_RATIO))
> +
> +/* CLK_SRC_TOP0        */
> +#define MUX_ACLK_300_GSCL_SEL           0x0
> +#define MUX_ACLK_300_GSCL_MID_SEL       0x0
> +#define MUX_ACLK_400_G3D_MID_SEL        0x0
> +#define MUX_ACLK_333_SEL               0x0
> +#define MUX_ACLK_300_DISP1_SEL         0x0
> +#define MUX_ACLK_300_DISP1_MID_SEL      0x0
> +#define MUX_ACLK_200_SEL               0x0
> +#define MUX_ACLK_166_SEL               0x0
> +#define CLK_SRC_TOP0_VAL       ((MUX_ACLK_300_GSCL_SEL  << 25)         \
> +                               | (MUX_ACLK_300_GSCL_MID_SEL << 24)     \
> +                               | (MUX_ACLK_400_G3D_MID_SEL << 20)      \
> +                               | (MUX_ACLK_333_SEL << 16)              \
> +                               | (MUX_ACLK_300_DISP1_SEL << 15)        \
> +                               | (MUX_ACLK_300_DISP1_MID_SEL << 14)    \
> +                               | (MUX_ACLK_200_SEL << 12)              \
> +                               | (MUX_ACLK_166_SEL << 8))
> +
> +/* CLK_SRC_TOP1        */
> +#define MUX_ACLK_400_G3D_SEL            0x1
> +#define MUX_ACLK_400_ISP_SEL            0x0
> +#define MUX_ACLK_400_IOP_SEL            0x0
> +#define MUX_ACLK_MIPI_HSI_TXBASE_SEL    0x0
> +#define MUX_ACLK_300_GSCL_MID1_SEL      0x0
> +#define MUX_ACLK_300_DISP1_MID1_SEL     0x0
> +#define CLK_SRC_TOP1_VAL       ((MUX_ACLK_400_G3D_SEL << 28)           \
> +                               |(MUX_ACLK_400_ISP_SEL << 24)           \
> +                               |(MUX_ACLK_400_IOP_SEL << 20)           \
> +                               |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16)   \
> +                               |(MUX_ACLK_300_GSCL_MID1_SEL << 12)     \
> +                               |(MUX_ACLK_300_DISP1_MID1_SEL << 8))
> +
> +/* CLK_SRC_TOP2 */
> +#define MUX_GPLL_SEL                    0x1
> +#define MUX_BPLL_USER_SEL               0x0
> +#define MUX_MPLL_USER_SEL               0x0
> +#define MUX_VPLL_SEL                    0x1
> +#define MUX_EPLL_SEL                    0x1
> +#define MUX_CPLL_SEL                    0x1
> +#define VPLLSRC_SEL                     0x0
> +#define CLK_SRC_TOP2_VAL       ((MUX_GPLL_SEL << 28)           \
> +                               | (MUX_BPLL_USER_SEL << 24)     \
> +                               | (MUX_MPLL_USER_SEL << 20)     \
> +                               | (MUX_VPLL_SEL << 16)          \
> +                               | (MUX_EPLL_SEL << 12)          \
> +                               | (MUX_CPLL_SEL << 8)           \
> +                               | (VPLLSRC_SEL))
> +/* CLK_SRC_TOP3 */
> +#define MUX_ACLK_333_SUB_SEL            0x1
> +#define MUX_ACLK_400_SUB_SEL            0x1
> +#define MUX_ACLK_266_ISP_SUB_SEL        0x1
> +#define MUX_ACLK_266_GPS_SUB_SEL        0x0
> +#define MUX_ACLK_300_GSCL_SUB_SEL       0x1
> +#define MUX_ACLK_266_GSCL_SUB_SEL       0x1
> +#define MUX_ACLK_300_DISP1_SUB_SEL      0x1
> +#define MUX_ACLK_200_DISP1_SUB_SEL      0x1
> +#define CLK_SRC_TOP3_VAL       ((MUX_ACLK_333_SUB_SEL << 24)           \
> +                               | (MUX_ACLK_400_SUB_SEL << 20)          \
> +                               | (MUX_ACLK_266_ISP_SUB_SEL << 16)      \
> +                               | (MUX_ACLK_266_GPS_SUB_SEL << 12)      \
> +                               | (MUX_ACLK_300_GSCL_SUB_SEL << 10)     \
> +                               | (MUX_ACLK_266_GSCL_SUB_SEL << 8)      \
> +                               | (MUX_ACLK_300_DISP1_SUB_SEL << 6)     \
> +                               | (MUX_ACLK_200_DISP1_SUB_SEL << 4))
> +
> +/* CLK_DIV_TOP0        */
> +#define ACLK_300_DISP1_RATIO   0x2
> +#define ACLK_400_G3D_RATIO     0x0
> +#define ACLK_333_RATIO         0x0
> +#define ACLK_266_RATIO         0x2
> +#define ACLK_200_RATIO         0x3
> +#define ACLK_166_RATIO         0x1
> +#define ACLK_133_RATIO         0x1
> +#define ACLK_66_RATIO          0x5
> +
> +#define CLK_DIV_TOP0_VAL       ((ACLK_300_DISP1_RATIO << 28)   \
> +                               | (ACLK_400_G3D_RATIO << 24)    \
> +                               | (ACLK_333_RATIO  << 20)       \
> +                               | (ACLK_266_RATIO << 16)        \
> +                               | (ACLK_200_RATIO << 12)        \
> +                               | (ACLK_166_RATIO << 8)         \
> +                               | (ACLK_133_RATIO << 4)         \
> +                               | (ACLK_66_RATIO))
> +
> +/* CLK_DIV_TOP1        */
> +#define ACLK_MIPI_HSI_TX_BASE_RATIO     0x3
> +#define ACLK_66_PRE_RATIO               0x1
> +#define ACLK_400_ISP_RATIO              0x1
> +#define ACLK_400_IOP_RATIO              0x1
> +#define ACLK_300_GSCL_RATIO             0x2
> +
> +#define CLK_DIV_TOP1_VAL       ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28)    \
> +                               | (ACLK_66_PRE_RATIO << 24)             \
> +                               | (ACLK_400_ISP_RATIO  << 20)           \
> +                               | (ACLK_400_IOP_RATIO << 16)            \
> +                               | (ACLK_300_GSCL_RATIO << 12))
> +
> +/* APLL_LOCK   */
> +#define APLL_LOCK_VAL  (0x546)
> +/* MPLL_LOCK   */
> +#define MPLL_LOCK_VAL  (0x546)
> +/* CPLL_LOCK   */
> +#define CPLL_LOCK_VAL  (0x546)
> +/* GPLL_LOCK   */
> +#define GPLL_LOCK_VAL  (0x546)
> +/* EPLL_LOCK   */
> +#define EPLL_LOCK_VAL  (0x3A98)
> +/* VPLL_LOCK   */
> +#define VPLL_LOCK_VAL  (0x3A98)
> +/* BPLL_LOCK   */
> +#define BPLL_LOCK_VAL  (0x546)
> +
> +#define MUX_APLL_SEL_MASK      (1 << 0)
> +#define MUX_MPLL_SEL_MASK      (1 << 8)
> +#define MPLL_SEL_MOUT_MPLLFOUT (2 << 8)
> +#define MUX_CPLL_SEL_MASK      (1 << 8)
> +#define MUX_EPLL_SEL_MASK      (1 << 12)
> +#define MUX_VPLL_SEL_MASK      (1 << 16)
> +#define MUX_GPLL_SEL_MASK      (1 << 28)
> +#define MUX_BPLL_SEL_MASK      (1 << 0)
> +#define MUX_HPM_SEL_MASK       (1 << 20)
> +#define HPM_SEL_SCLK_MPLL      (1 << 21)
> +#define APLL_CON0_LOCKED       (1 << 29)
> +#define MPLL_CON0_LOCKED       (1 << 29)
> +#define BPLL_CON0_LOCKED       (1 << 29)
> +#define CPLL_CON0_LOCKED       (1 << 29)
> +#define EPLL_CON0_LOCKED       (1 << 29)
> +#define GPLL_CON0_LOCKED       (1 << 29)
> +#define VPLL_CON0_LOCKED       (1 << 29)
> +#define CLK_REG_DISABLE                0x0
> +#define TOP2_VAL               0x0110000
> +
> +/* CLK_SRC_PERIC0 */
> +#define PWM_SEL                0
> +#define UART3_SEL      6
> +#define UART2_SEL      6
> +#define UART1_SEL      6
> +#define UART0_SEL      6
> +/* SRC_CLOCK = SCLK_MPLL */
> +#define CLK_SRC_PERIC0_VAL     ((PWM_SEL << 24)        \
> +                               | (UART3_SEL << 12)     \
> +                               | (UART2_SEL << 8)       \
> +                               | (UART1_SEL << 4)      \
> +                               | (UART0_SEL))
> +
> +/* CLK_SRC_PERIC1 */
> +/* SRC_CLOCK = SCLK_MPLL */
> +#define SPI0_SEL               6
> +#define SPI1_SEL               6
> +#define SPI2_SEL               6
> +#define CLK_SRC_PERIC1_VAL     ((SPI2_SEL << 24) \
> +                               | (SPI1_SEL << 20) \
> +                               | (SPI0_SEL << 16))
> +
> +/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
> +#define SPI0_ISP_SEL           6
> +#define SPI1_ISP_SEL           6
> +#define SCLK_SRC_ISP_VAL       (SPI1_ISP_SEL << 4) \
> +                               | (SPI0_ISP_SEL << 0)
> +
> +/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
> +#define SPI0_ISP_RATIO         0xf
> +#define SPI1_ISP_RATIO         0xf
> +#define SCLK_DIV_ISP_VAL       (SPI1_ISP_RATIO << 12) \
> +                               | (SPI0_ISP_RATIO << 0)
> +
> +/* CLK_DIV_PERIL0      */
> +#define UART5_RATIO    7
> +#define UART4_RATIO    7
> +#define UART3_RATIO    7
> +#define UART2_RATIO    7
> +#define UART1_RATIO    7
> +#define UART0_RATIO    7
> +
> +#define CLK_DIV_PERIC0_VAL     ((UART3_RATIO << 12)    \
> +                               | (UART2_RATIO << 8)    \
> +                               | (UART1_RATIO << 4)    \
> +                               | (UART0_RATIO))
> +/* CLK_DIV_PERIC1 */
> +#define SPI1_RATIO             0x7
> +#define SPI0_RATIO             0xf
> +#define SPI1_SUB_RATIO         0x0
> +#define SPI0_SUB_RATIO         0x0
> +#define CLK_DIV_PERIC1_VAL     ((SPI1_SUB_RATIO << 24) \
> +                               | ((SPI1_RATIO << 16) \
> +                               | (SPI0_SUB_RATIO << 8) \
> +                               | (SPI0_RATIO << 0)))
> +
> +/* CLK_DIV_PERIC2 */
> +#define SPI2_RATIO             0xf
> +#define SPI2_SUB_RATIO         0x0
> +#define CLK_DIV_PERIC2_VAL     ((SPI2_SUB_RATIO << 8) \
> +                               | (SPI2_RATIO << 0))
> +
> +/* CLK_DIV_PERIC3 */
> +#define PWM_RATIO              8
> +#define CLK_DIV_PERIC3_VAL     (PWM_RATIO << 0)
> +
> +/* CLK_DIV_FSYS2 */
> +#define MMC2_RATIO_MASK                0xf
> +#define MMC2_RATIO_VAL         0x3
> +#define MMC2_RATIO_OFFSET      0
> +
> +#define MMC2_PRE_RATIO_MASK    0xff
> +#define MMC2_PRE_RATIO_VAL     0x9
> +#define MMC2_PRE_RATIO_OFFSET  8
> +
> +#define MMC3_RATIO_MASK                0xf
> +#define MMC3_RATIO_VAL         0x1
> +#define MMC3_RATIO_OFFSET      16
> +
> +#define MMC3_PRE_RATIO_MASK    0xff
> +#define MMC3_PRE_RATIO_VAL     0x0
> +#define MMC3_PRE_RATIO_OFFSET  24
> +
> +/* CLK_SRC_LEX */
> +#define CLK_SRC_LEX_VAL         0x0
> +
> +/* CLK_DIV_LEX */
> +#define CLK_DIV_LEX_VAL         0x10
> +
> +/* CLK_DIV_R0X */
> +#define CLK_DIV_R0X_VAL         0x10
> +
> +/* CLK_DIV_L0X */
> +#define CLK_DIV_R1X_VAL         0x10
> +
> +/* CLK_DIV_ISP0 */
> +#define CLK_DIV_ISP0_VAL        0x31
> +
> +/* CLK_DIV_ISP1 */
> +#define CLK_DIV_ISP1_VAL        0x0
> +
> +/* CLK_DIV_ISP2 */
> +#define CLK_DIV_ISP2_VAL        0x1
> +
> +/* CLK_SRC_DISP1_0 */
> +#define CLK_SRC_DISP1_0_VAL    0x6
> +
> +/*
> + * DIV_DISP1_0
> + * For DP, divisor should be 2
> + */
> +#define CLK_DIV_DISP1_0_FIMD1  (2 << 0)
> +
> +/* CLK_GATE_IP_DISP1 */
> +#define CLK_GATE_DP1_ALLOW     (1 << 4)
> +
> +#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
> +#define DDR3PHY_CTRL_PHY_RESET_OFF     (0 << 0)
> +
> +#define PHY_CON0_RESET_VAL     0x17020a40
> +#define P0_CMD_EN              (1 << 14)
> +#define BYTE_RDLVL_EN          (1 << 13)
> +#define CTRL_SHGATE            (1 << 8)
> +
> +#define PHY_CON1_RESET_VAL     0x09210100
> +#define CTRL_GATEDURADJ_MASK   (0xf << 20)
> +
> +#define PHY_CON2_RESET_VAL     0x00010004
> +#define INIT_DESKEW_EN         (1 << 6)
> +#define RDLVL_GATE_EN          (1 << 24)
> +
> +/*ZQ Configurations */
> +#define PHY_CON16_RESET_VAL    0x08000304
> +
> +#define ZQ_CLK_DIV_EN          (1 << 18)
> +#define ZQ_MANUAL_STR          (1 << 1)
> +#define ZQ_DONE                        (1 << 0)
> +
> +#define CTRL_RDLVL_GATE_ENABLE 1
> +#define CTRL_RDLVL_GATE_DISABLE        1
> +
> +/* Direct Command */
> +#define DIRECT_CMD_NOP                 0x07000000
> +#define DIRECT_CMD_PALL                        0x01000000
> +#define DIRECT_CMD_ZQINIT              0x0a000000
> +#define DIRECT_CMD_CHANNEL_SHIFT       28
> +#define DIRECT_CMD_CHIP_SHIFT          20
> +
> +/* DMC PHY Control0 register */
> +#define PHY_CONTROL0_RESET_VAL 0x0
> +#define MEM_TERM_EN    (1 << 31)       /* Termination enable for memory */
> +#define PHY_TERM_EN    (1 << 30)       /* Termination enable for PHY */
> +#define DMC_CTRL_SHGATE        (1 << 29)       /* Duration of DQS gating signal */
> +#define FP_RSYNC       (1 << 3)        /* Force DLL resyncronization */
> +
> +/* Driver strength for CK, CKE, CS & CA */
> +#define IMP_OUTPUT_DRV_40_OHM  0x5
> +#define IMP_OUTPUT_DRV_30_OHM  0x7
> +#define CA_CK_DRVR_DS_OFFSET   9
> +#define CA_CKE_DRVR_DS_OFFSET  6
> +#define CA_CS_DRVR_DS_OFFSET   3
> +#define CA_ADR_DRVR_DS_OFFSET  0
> +
> +#define PHY_CON42_CTRL_BSTLEN_SHIFT    8
> +#define PHY_CON42_CTRL_RDLAT_SHIFT     0
> +
> +struct mem_timings;
> +
> +/* Errors that we can encourter in low-level setup */
> +enum {
> +       SETUP_ERR_OK,
> +       SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
> +       SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
> +};
> +
> +/*
> + * Memory variant specific initialization code
> + *
> + * @param mem          Memory timings for this memory type.
> + * @param mem_iv_size  Memory interleaving size is a configurable parameter
> + *                     which the DMC uses to decide how to split a memory
> + *                     chunk into smaller chunks to support concurrent
> + *                     accesses; may vary across boards.
> + * @return 0 if ok, SETUP_ERR_... if there is a problem
> + */
> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
> +
> +/*
> + * Configure ZQ I/O interface
> + *
> + * @param mem          Memory timings for this memory type.
> + * @param phy0_ctrl    Pointer to struct containing PHY0 control reg
> + * @param phy1_ctrl    Pointer to struct containing PHY1 control reg
> + * @return 0 if ok, -1 on error
> + */
> +int dmc_config_zq(struct mem_timings *mem,
> +                 struct exynos5_phy_control *phy0_ctrl,
> +                 struct exynos5_phy_control *phy1_ctrl);
> +
> +/*
> + * Send NOP and MRS/EMRS Direct commands
> + *
> + * @param mem          Memory timings for this memory type.
> + * @param dmc          Pointer to struct of DMC registers
> + */
> +void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
> +
> +/*
> + * Send PALL Direct commands
> + *
> + * @param mem          Memory timings for this memory type.
> + * @param dmc          Pointer to struct of DMC registers
> + */
> +void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
> +
> +/*
> + * Configure the memconfig and membaseconfig registers
> + *
> + * @param mem          Memory timings for this memory type.
> + * @param exynos5_dmc  Pointer to struct of DMC registers
> + */
> +void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
> +
> +/*
> + * Reset the DLL. This function is common between DDR3 and LPDDR2.
> + * However, the reset value is different. So we are passing a flag
> + * ddr_mode to distinguish between LPDDR2 and DDR3.
> + *
> + * @param exynos5_dmc  Pointer to struct of DMC registers
> + * @param ddr_mode     Type of DDR memory
> + */
> +void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
> +
> +void sdelay(unsigned long);
> +void mem_ctrl_init(void);
> +void system_clock_init(void);
> +#endif
> diff --git a/board/samsung/dts/exynos5250-arndale.dts b/board/samsung/dts/exynos5250-arndale.dts
> new file mode 100644
> index 0000000..9b4d6b2
> --- /dev/null
> +++ b/board/samsung/dts/exynos5250-arndale.dts
> @@ -0,0 +1,36 @@
> +/*
> + * SAMSUNG Arndale board device tree source
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *             http://www.samsung.com
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +/dts-v1/;
> +/include/ ARCH_CPU_DTS
> +
> +/ {
> +       model = "SAMSUNG Arndale board based on EXYNOS5250";
> +       compatible = "samsung,arndale", "samsung,exynos5250";
> +
> +       mmc@12200000 {
> +               samsung,bus-width = <8>;
> +               samsung,timing = <1 3 3>;
> +       };
> +
> +       mmc@12210000 {
> +               status = "disabled";
> +       };
> +
> +       mmc@12220000 {
> +               samsung,bus-width = <4>;
> +               samsung,timing = <1 2 3>;
> +       };
> +
> +       mmc@12230000 {
> +               status = "disabled";
> +       };
> +};
> diff --git a/boards.cfg b/boards.cfg
> index 54357eb..572b242 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -288,6 +288,7 @@ origen                           arm         armv7       origen              samsung        exynos
>  s5pc210_universal            arm         armv7       universal_c210      samsung        exynos
>  snow                        arm         armv7       smdk5250            samsung        exynos
>  smdk5250                    arm         armv7       smdk5250            samsung        exynos
> +arndale                             arm         armv7       arndale             samsung        exynos
>  smdkv310                    arm         armv7       smdkv310            samsung        exynos
>  trats                        arm         armv7       trats               samsung        exynos
>  harmony                      arm         armv7:arm720t harmony           nvidia         tegra20
> diff --git a/include/configs/arndale.h b/include/configs/arndale.h
> new file mode 100644
> index 0000000..caa83b8
> --- /dev/null
> +++ b/include/configs/arndale.h
> @@ -0,0 +1,39 @@
> +/*
> + * Copyright (C) 2013 Samsung Electronics
> + *
> + * Configuration settings for the SAMSUNG Arndale board.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_ARNDALE_H
> +#define __CONFIG_ARNDALE_H
> +
> +#undef CONFIG_DEFAULT_DEVICE_TREE
> +#define CONFIG_DEFAULT_DEVICE_TREE     exynos5250-arndale
> +
> +#define CONFIG_ARNDALE
> +
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SERIAL2
> +#define CONFIG_IDENT_STRING            " for Arndale"
> +
> +#include <configs/exynos5250-dt.h>
> +
> +#endif /* __CONFIG_ARNDALE_H */
> diff --git a/tools/Makefile b/tools/Makefile
> index c5952fc..ab7d339 100644
> --- a/tools/Makefile
> +++ b/tools/Makefile
> @@ -69,6 +69,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
>  BIN_FILES-y += mkenvimage$(SFX)
>  BIN_FILES-y += mkimage$(SFX)
>  BIN_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl$(SFX)
> +BIN_FILES-$(CONFIG_ARNDALE) += mkarndalespl$(SFX)
>  BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
>  BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
>  BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
> @@ -99,6 +100,7 @@ NOPED_OBJ_FILES-y += omapimage.o
>  NOPED_OBJ_FILES-y += mkenvimage.o
>  NOPED_OBJ_FILES-y += mkimage.o
>  OBJ_FILES-$(CONFIG_SMDK5250) += mkexynosspl.o
> +OBJ_FILES-$(CONFIG_ARNDALE) += mkexynosspl.o
>  OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
>  OBJ_FILES-$(CONFIG_MX28) += mxsboot.o
>  OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o
> --
> 1.7.9.5
>
> _______________________________________________
> U-Boot mailing list
> U-Boot@lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
Wolfgang Denk March 26, 2013, 11:34 a.m. UTC | #2
Dear Inderpal Singh,

In message <1364290670-7443-4-git-send-email-inderpal.singh@linaro.org> you wrote:
> Arndale board is based on samsung's exynos5250 soc.


WARNING: Avoid CamelCase: <DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED>
#618: FILE: board/samsung/arndale/clock_init.c:213:
+		.memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |

WARNING: Avoid CamelCase: <DMC_MEMBASECONFIGx_CHIP_BASE>
#1860: FILE: board/samsung/arndale/setup.h:102:
+#define DMC_MEMBASECONFIGx_CHIP_BASE(x)         (x << 16)

WARNING: Avoid CamelCase: <DMC_MEMBASECONFIGx_CHIP_MASK>
#1861: FILE: board/samsung/arndale/setup.h:103:
+#define DMC_MEMBASECONFIGx_CHIP_MASK(x)         (x << 0)

ERROR: Macros with complex values should be enclosed in parenthesis
#2116: FILE: board/samsung/arndale/setup.h:358:
+#define SCLK_SRC_ISP_VAL	(SPI1_ISP_SEL << 4) \
+				| (SPI0_ISP_SEL << 0)

ERROR: Macros with complex values should be enclosed in parenthesis
#2122: FILE: board/samsung/arndale/setup.h:364:
+#define SCLK_DIV_ISP_VAL	(SPI1_ISP_RATIO << 12) \
+				| (SPI0_ISP_RATIO << 0)

ERROR: Macros with complex values should be enclosed in parenthesis
#2416: FILE: include/configs/arndale.h:29:
+#define CONFIG_DEFAULT_DEVICE_TREE	exynos5250-arndale

total: 3 errors, 3 warnings, 2235 lines checked

/home/wd/Mail/U-Boot/7161 has style problems, please review.


Best regards,

Wolfgang Denk
Inderpal Singh March 27, 2013, 6:04 a.m. UTC | #3
Hi Rajeshwari,


On 26 March 2013 16:46, Rajeshwari Birje <rajeshwari.birje@gmail.com> wrote:
> Hi Inderpal Sigh,
>
> Most of the files added here are same as in SMDK5250, then can't we
> use the same code instead of adding a new folder?
>

I had thought about it, in fact I had sent a patch few days back to
use the same folder as smdk5250.
But, there could be few board specific things like gpios etc which I
think should be done in board specific folder.
Hence this approach.

Thanks,
Inder

> Regards,
> Rajeshwari Shinde.
>
> On Tue, Mar 26, 2013 at 3:07 PM, Inderpal Singh
> <inderpal.singh@linaro.org> wrote:
>> Arndale board is based on samsung's exynos5250 soc.
>>
>> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
>> ---
>>  MAINTAINERS                              |    4 +
>>  board/samsung/arndale/Makefile           |   54 +++
>>  board/samsung/arndale/arndale.c          |  117 ++++++
>>  board/samsung/arndale/arndale_spl.c      |   66 +++
>>  board/samsung/arndale/clock_init.c       |  655 ++++++++++++++++++++++++++++++
>>  board/samsung/arndale/clock_init.h       |  149 +++++++
>>  board/samsung/arndale/dmc_common.c       |  199 +++++++++
>>  board/samsung/arndale/dmc_init_ddr3.c    |  228 +++++++++++
>>  board/samsung/arndale/lowlevel_init.S    |   92 +++++
>>  board/samsung/arndale/setup.h            |  569 ++++++++++++++++++++++++++
>>  board/samsung/dts/exynos5250-arndale.dts |   36 ++
>>  boards.cfg                               |    1 +
>>  include/configs/arndale.h                |   39 ++
>>  tools/Makefile                           |    2 +
>>  14 files changed, 2211 insertions(+)
>>  create mode 100644 board/samsung/arndale/Makefile
>>  create mode 100644 board/samsung/arndale/arndale.c
>>  create mode 100644 board/samsung/arndale/arndale_spl.c
>>  create mode 100644 board/samsung/arndale/clock_init.c
>>  create mode 100644 board/samsung/arndale/clock_init.h
>>  create mode 100644 board/samsung/arndale/dmc_common.c
>>  create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
>>  create mode 100644 board/samsung/arndale/lowlevel_init.S
>>  create mode 100644 board/samsung/arndale/setup.h
>>  create mode 100644 board/samsung/dts/exynos5250-arndale.dts
>>  create mode 100644 include/configs/arndale.h
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index f6723ef..b112581 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -736,6 +736,10 @@ Chander Kashyap <k.chander@samsung.com>
>>         SMDKV310                ARM ARMV7 (EXYNOS4210 SoC)
>>         SMDK5250                ARM ARMV7 (EXYNOS5250 SoC)
>>
>> +Inderpal Singh <inderpal.singh@linaro.org>
>> +
>> +       Arndale                 ARM ARMV7 (EXYNOS5250 SoC)
>> +
>>  Lukasz Majewski <l.majewski@samsung.com>
>>
>>         trats                   ARM ARMV7 (EXYNOS4210 SoC)
>> diff --git a/board/samsung/arndale/Makefile b/board/samsung/arndale/Makefile
>> new file mode 100644
>> index 0000000..f65d111
>> --- /dev/null
>> +++ b/board/samsung/arndale/Makefile
>> @@ -0,0 +1,54 @@
>> +#
>> +# Copyright (C) 2013 Samsung Electronics
>> +#
>> +# See file CREDITS for list of people who contributed to this
>> +# project.
>> +#
>> +# This program is free software; you can redistribute it and/or
>> +# modify it under the terms of the GNU General Public License as
>> +# published by the Free Software Foundation; either version 2 of
>> +# the License, or (at your option) any later version.
>> +#
>> +# This program is distributed in the hope that it will be useful,
>> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
>> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> +# GNU General Public License for more details.
>> +#
>> +# You should have received a copy of the GNU General Public License
>> +# along with this program; if not, write to the Free Software
>> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> +# MA 02111-1307 USA
>> +#
>> +
>> +include $(TOPDIR)/config.mk
>> +
>> +LIB    = $(obj)lib$(BOARD).o
>> +
>> +SOBJS  := lowlevel_init.o
>> +
>> +COBJS  := clock_init.o
>> +COBJS  += dmc_common.o dmc_init_ddr3.o
>> +COBJS  += arndale_spl.o
>> +
>> +ifndef CONFIG_SPL_BUILD
>> +COBJS  += arndale.o
>> +endif
>> +
>> +SRCS   := $(SOBJS:.o=.S) $(COBJS:.o=.c)
>> +OBJS   := $(addprefix $(obj),$(COBJS) $(SOBJS))
>> +
>> +ALL    :=       $(obj).depend $(LIB)
>> +
>> +all:   $(ALL)
>> +
>> +$(LIB):        $(OBJS)
>> +       $(call cmd_link_o_target, $(OBJS))
>> +
>> +#########################################################################
>> +
>> +# defines $(obj).depend target
>> +include $(SRCTREE)/rules.mk
>> +
>> +sinclude $(obj).depend
>> +
>> +#########################################################################
>> diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
>> new file mode 100644
>> index 0000000..7f8a568
>> --- /dev/null
>> +++ b/board/samsung/arndale/arndale.c
>> @@ -0,0 +1,117 @@
>> +/*
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/arch/pinmux.h>
>> +#include <asm/arch/dwmmc.h>
>> +#include <asm/arch/power.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +int board_init(void)
>> +{
>> +       gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
>> +       return 0;
>> +}
>> +
>> +int dram_init(void)
>> +{
>> +       int i;
>> +       u32 addr;
>> +
>> +       for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
>> +               addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
>> +               gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
>> +       }
>> +       return 0;
>> +}
>> +
>> +int power_init_board(void)
>> +{
>> +       set_ps_hold_ctrl();
>> +       return 0;
>> +}
>> +
>> +void dram_init_banksize(void)
>> +{
>> +       int i;
>> +       u32 addr, size;
>> +
>> +       for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
>> +               addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
>> +               size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
>> +
>> +               gd->bd->bi_dram[i].start = addr;
>> +               gd->bd->bi_dram[i].size = size;
>> +       }
>> +}
>> +
>> +#ifdef CONFIG_GENERIC_MMC
>> +int board_mmc_init(bd_t *bis)
>> +{
>> +       int ret;
>> +       /* dwmmc initializattion for available channels */
>> +       ret = exynos_dwmmc_init(gd->fdt_blob);
>> +       if (ret)
>> +               debug("dwmmc init failed\n");
>> +
>> +       return ret;
>> +}
>> +#endif
>> +
>> +static int board_uart_init(void)
>> +{
>> +       int err, uart_id, ret = 0;
>> +
>> +       for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
>> +               err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
>> +               if (err) {
>> +                       debug("UART%d not configured\n",
>> +                                        (uart_id - PERIPH_ID_UART0));
>> +                       ret |= err;
>> +               }
>> +       }
>> +       return ret;
>> +}
>> +
>> +#ifdef CONFIG_BOARD_EARLY_INIT_F
>> +int board_early_init_f(void)
>> +{
>> +       int err;
>> +       err = board_uart_init();
>> +       if (err) {
>> +               debug("UART init failed\n");
>> +               return err;
>> +       }
>> +       return err;
>> +}
>> +#endif
>> +
>> +#ifdef CONFIG_DISPLAY_BOARDINFO
>> +int checkboard(void)
>> +{
>> +       printf("\nBoard: Arndale\n");
>> +
>> +       return 0;
>> +}
>> +#endif
>> +
>> diff --git a/board/samsung/arndale/arndale_spl.c b/board/samsung/arndale/arndale_spl.c
>> new file mode 100644
>> index 0000000..8135708
>> --- /dev/null
>> +++ b/board/samsung/arndale/arndale_spl.c
>> @@ -0,0 +1,66 @@
>> +/*
>> + * Copyright (c) 2012 The Chromium OS Authors.
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/arch/spl.h>
>> +
>> +#define SIGNATURE      0xdeadbeef
>> +
>> +/* Parameters of early board initialization in SPL */
>> +static struct spl_machine_param machine_param
>> +               __attribute__((section(".machine_param"))) = {
>> +       .signature      = SIGNATURE,
>> +       .version        = 1,
>> +       .params         = "vmubfasirM",
>> +       .size           = sizeof(machine_param),
>> +
>> +       .mem_iv_size    = 0x1f,
>> +       .mem_type       = DDR_MODE_DDR3,
>> +
>> +       /*
>> +        * Set uboot_size to 0x100000 bytes.
>> +        *
>> +        * This is an overly conservative value chosen to accommodate all
>> +        * possible U-Boot image.  You are advised to set this value to a
>> +        * smaller realistic size via scripts that modifies the .machine_param
>> +        * section of output U-Boot image.
>> +        */
>> +       .uboot_size     = 0x100000,
>> +
>> +       .boot_source    = BOOT_MODE_OM,
>> +       .frequency_mhz  = 800,
>> +       .arm_freq_mhz   = 1000,
>> +       .serial_base    = 0x12c30000,
>> +       .i2c_base       = 0x12c60000,
>> +       .mem_manuf      = MEM_MANUF_SAMSUNG,
>> +};
>> +
>> +struct spl_machine_param *spl_get_machine_params(void)
>> +{
>> +       if (machine_param.signature != SIGNATURE) {
>> +               /* Will hang if SIGNATURE dont match */
>> +               while (1)
>> +                       ;
>> +       }
>> +
>> +       return &machine_param;
>> +}
>> diff --git a/board/samsung/arndale/clock_init.c b/board/samsung/arndale/clock_init.c
>> new file mode 100644
>> index 0000000..a9b0bbd
>> --- /dev/null
>> +++ b/board/samsung/arndale/clock_init.c
>> @@ -0,0 +1,655 @@
>> +/*
>> + * Clock setup for Arndale board based on EXYNOS5
>> + *
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <common.h>
>> +#include <config.h>
>> +#include <asm/io.h>
>> +#include <asm/arch/clk.h>
>> +#include <asm/arch/clock.h>
>> +#include <asm/arch/spl.h>
>> +
>> +#include "clock_init.h"
>> +#include "setup.h"
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +struct arm_clk_ratios arm_clk_ratios[] = {
>> +       {
>> +               .arm_freq_mhz = 600,
>> +
>> +               .apll_mdiv = 0xc8,
>> +               .apll_pdiv = 0x4,
>> +               .apll_sdiv = 0x1,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x1,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x2,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x1,
>> +               .arm_ratio = 0x0,
>> +       }, {
>> +               .arm_freq_mhz = 800,
>> +
>> +               .apll_mdiv = 0x64,
>> +               .apll_pdiv = 0x3,
>> +               .apll_sdiv = 0x0,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x1,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x3,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x2,
>> +               .arm_ratio = 0x0,
>> +       }, {
>> +               .arm_freq_mhz = 1000,
>> +
>> +               .apll_mdiv = 0x7d,
>> +               .apll_pdiv = 0x3,
>> +               .apll_sdiv = 0x0,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x1,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x4,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x2,
>> +               .arm_ratio = 0x0,
>> +       }, {
>> +               .arm_freq_mhz = 1200,
>> +
>> +               .apll_mdiv = 0x96,
>> +               .apll_pdiv = 0x3,
>> +               .apll_sdiv = 0x0,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x3,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x5,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x3,
>> +               .arm_ratio = 0x0,
>> +       }, {
>> +               .arm_freq_mhz = 1400,
>> +
>> +               .apll_mdiv = 0xaf,
>> +               .apll_pdiv = 0x3,
>> +               .apll_sdiv = 0x0,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x3,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x6,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x3,
>> +               .arm_ratio = 0x0,
>> +       }, {
>> +               .arm_freq_mhz = 1700,
>> +
>> +               .apll_mdiv = 0x1a9,
>> +               .apll_pdiv = 0x6,
>> +               .apll_sdiv = 0x0,
>> +
>> +               .arm2_ratio = 0x0,
>> +               .apll_ratio = 0x3,
>> +               .pclk_dbg_ratio = 0x1,
>> +               .atb_ratio = 0x6,
>> +               .periph_ratio = 0x7,
>> +               .acp_ratio = 0x7,
>> +               .cpud_ratio = 0x3,
>> +               .arm_ratio = 0x0,
>> +       }
>> +};
>> +struct mem_timings mem_timings[] = {
>> +       {
>> +               .mem_manuf = MEM_MANUF_ELPIDA,
>> +               .mem_type = DDR_MODE_DDR3,
>> +               .frequency_mhz = 800,
>> +               .mpll_mdiv = 0xc8,
>> +               .mpll_pdiv = 0x3,
>> +               .mpll_sdiv = 0x0,
>> +               .cpll_mdiv = 0xde,
>> +               .cpll_pdiv = 0x4,
>> +               .cpll_sdiv = 0x2,
>> +               .gpll_mdiv = 0x215,
>> +               .gpll_pdiv = 0xc,
>> +               .gpll_sdiv = 0x1,
>> +               .epll_mdiv = 0x60,
>> +               .epll_pdiv = 0x3,
>> +               .epll_sdiv = 0x3,
>> +               .vpll_mdiv = 0x96,
>> +               .vpll_pdiv = 0x3,
>> +               .vpll_sdiv = 0x2,
>> +
>> +               .bpll_mdiv = 0x64,
>> +               .bpll_pdiv = 0x3,
>> +               .bpll_sdiv = 0x0,
>> +               .pclk_cdrex_ratio = 0x5,
>> +               .direct_cmd_msr = {
>> +                       0x00020018, 0x00030000, 0x00010042, 0x00000d70
>> +               },
>> +               .timing_ref = 0x000000bb,
>> +               .timing_row = 0x8c36650e,
>> +               .timing_data = 0x3630580b,
>> +               .timing_power = 0x41000a44,
>> +               .phy0_dqs = 0x08080808,
>> +               .phy1_dqs = 0x08080808,
>> +               .phy0_dq = 0x08080808,
>> +               .phy1_dq = 0x08080808,
>> +               .phy0_tFS = 0x4,
>> +               .phy1_tFS = 0x4,
>> +               .phy0_pulld_dqs = 0xf,
>> +               .phy1_pulld_dqs = 0xf,
>> +
>> +               .lpddr3_ctrl_phy_reset = 0x1,
>> +               .ctrl_start_point = 0x10,
>> +               .ctrl_inc = 0x10,
>> +               .ctrl_start = 0x1,
>> +               .ctrl_dll_on = 0x1,
>> +               .ctrl_ref = 0x8,
>> +
>> +               .ctrl_force = 0x1a,
>> +               .ctrl_rdlat = 0x0b,
>> +               .ctrl_bstlen = 0x08,
>> +
>> +               .fp_resync = 0x8,
>> +               .iv_size = 0x7,
>> +               .dfi_init_start = 1,
>> +               .aref_en = 1,
>> +
>> +               .rd_fetch = 0x3,
>> +
>> +               .zq_mode_dds = 0x7,
>> +               .zq_mode_term = 0x1,
>> +               .zq_mode_noterm = 0,
>> +
>> +               /*
>> +               * Dynamic Clock: Always Running
>> +               * Memory Burst length: 8
>> +               * Number of chips: 1
>> +               * Memory Bus width: 32 bit
>> +               * Memory Type: DDR3
>> +               * Additional Latancy for PLL: 0 Cycle
>> +               */
>> +               .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
>> +                       DMC_MEMCONTROL_DPWRDN_DISABLE |
>> +                       DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
>> +                       DMC_MEMCONTROL_TP_DISABLE |
>> +                       DMC_MEMCONTROL_DSREF_ENABLE |
>> +                       DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
>> +                       DMC_MEMCONTROL_MEM_TYPE_DDR3 |
>> +                       DMC_MEMCONTROL_MEM_WIDTH_32BIT |
>> +                       DMC_MEMCONTROL_NUM_CHIP_1 |
>> +                       DMC_MEMCONTROL_BL_8 |
>> +                       DMC_MEMCONTROL_PZQ_DISABLE |
>> +                       DMC_MEMCONTROL_MRR_BYTE_7_0,
>> +               .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
>> +                       DMC_MEMCONFIGx_CHIP_COL_10 |
>> +                       DMC_MEMCONFIGx_CHIP_ROW_15 |
>> +                       DMC_MEMCONFIGx_CHIP_BANK_8,
>> +               .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
>> +               .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
>> +               .prechconfig_tp_cnt = 0xff,
>> +               .dpwrdn_cyc = 0xff,
>> +               .dsref_cyc = 0xffff,
>> +               .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
>> +                       DMC_CONCONTROL_TIMEOUT_LEVEL0 |
>> +                       DMC_CONCONTROL_RD_FETCH_DISABLE |
>> +                       DMC_CONCONTROL_EMPTY_DISABLE |
>> +                       DMC_CONCONTROL_AREF_EN_DISABLE |
>> +                       DMC_CONCONTROL_IO_PD_CON_DISABLE,
>> +               .dmc_channels = 2,
>> +               .chips_per_channel = 2,
>> +               .chips_to_configure = 1,
>> +               .send_zq_init = 1,
>> +               .impedance = IMP_OUTPUT_DRV_30_OHM,
>> +               .gate_leveling_enable = 0,
>> +       }, {
>> +               .mem_manuf = MEM_MANUF_SAMSUNG,
>> +               .mem_type = DDR_MODE_DDR3,
>> +               .frequency_mhz = 800,
>> +               .mpll_mdiv = 0xc8,
>> +               .mpll_pdiv = 0x3,
>> +               .mpll_sdiv = 0x0,
>> +               .cpll_mdiv = 0xde,
>> +               .cpll_pdiv = 0x4,
>> +               .cpll_sdiv = 0x2,
>> +               .gpll_mdiv = 0x215,
>> +               .gpll_pdiv = 0xc,
>> +               .gpll_sdiv = 0x1,
>> +               .epll_mdiv = 0x60,
>> +               .epll_pdiv = 0x3,
>> +               .epll_sdiv = 0x3,
>> +               .vpll_mdiv = 0x96,
>> +               .vpll_pdiv = 0x3,
>> +               .vpll_sdiv = 0x2,
>> +
>> +               .bpll_mdiv = 0x64,
>> +               .bpll_pdiv = 0x3,
>> +               .bpll_sdiv = 0x0,
>> +               .pclk_cdrex_ratio = 0x5,
>> +               .direct_cmd_msr = {
>> +                       0x00020018, 0x00030000, 0x00010000, 0x00000d70
>> +               },
>> +               .timing_ref = 0x000000bb,
>> +               .timing_row = 0x8c36650e,
>> +               .timing_data = 0x3630580b,
>> +               .timing_power = 0x41000a44,
>> +               .phy0_dqs = 0x08080808,
>> +               .phy1_dqs = 0x08080808,
>> +               .phy0_dq = 0x08080808,
>> +               .phy1_dq = 0x08080808,
>> +               .phy0_tFS = 0x8,
>> +               .phy1_tFS = 0x8,
>> +               .phy0_pulld_dqs = 0xf,
>> +               .phy1_pulld_dqs = 0xf,
>> +
>> +               .lpddr3_ctrl_phy_reset = 0x1,
>> +               .ctrl_start_point = 0x10,
>> +               .ctrl_inc = 0x10,
>> +               .ctrl_start = 0x1,
>> +               .ctrl_dll_on = 0x1,
>> +               .ctrl_ref = 0x8,
>> +
>> +               .ctrl_force = 0x1a,
>> +               .ctrl_rdlat = 0x0b,
>> +               .ctrl_bstlen = 0x08,
>> +
>> +               .fp_resync = 0x8,
>> +               .iv_size = 0x7,
>> +               .dfi_init_start = 1,
>> +               .aref_en = 1,
>> +
>> +               .rd_fetch = 0x3,
>> +
>> +               .zq_mode_dds = 0x5,
>> +               .zq_mode_term = 0x1,
>> +               .zq_mode_noterm = 1,
>> +
>> +               /*
>> +               * Dynamic Clock: Always Running
>> +               * Memory Burst length: 8
>> +               * Number of chips: 1
>> +               * Memory Bus width: 32 bit
>> +               * Memory Type: DDR3
>> +               * Additional Latancy for PLL: 0 Cycle
>> +               */
>> +               .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
>> +                       DMC_MEMCONTROL_DPWRDN_DISABLE |
>> +                       DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
>> +                       DMC_MEMCONTROL_TP_DISABLE |
>> +                       DMC_MEMCONTROL_DSREF_ENABLE |
>> +                       DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
>> +                       DMC_MEMCONTROL_MEM_TYPE_DDR3 |
>> +                       DMC_MEMCONTROL_MEM_WIDTH_32BIT |
>> +                       DMC_MEMCONTROL_NUM_CHIP_1 |
>> +                       DMC_MEMCONTROL_BL_8 |
>> +                       DMC_MEMCONTROL_PZQ_DISABLE |
>> +                       DMC_MEMCONTROL_MRR_BYTE_7_0,
>> +               .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
>> +                       DMC_MEMCONFIGx_CHIP_COL_10 |
>> +                       DMC_MEMCONFIGx_CHIP_ROW_15 |
>> +                       DMC_MEMCONFIGx_CHIP_BANK_8,
>> +               .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
>> +               .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
>> +               .prechconfig_tp_cnt = 0xff,
>> +               .dpwrdn_cyc = 0xff,
>> +               .dsref_cyc = 0xffff,
>> +               .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
>> +                       DMC_CONCONTROL_TIMEOUT_LEVEL0 |
>> +                       DMC_CONCONTROL_RD_FETCH_DISABLE |
>> +                       DMC_CONCONTROL_EMPTY_DISABLE |
>> +                       DMC_CONCONTROL_AREF_EN_DISABLE |
>> +                       DMC_CONCONTROL_IO_PD_CON_DISABLE,
>> +               .dmc_channels = 2,
>> +               .chips_per_channel = 2,
>> +               .chips_to_configure = 1,
>> +               .send_zq_init = 1,
>> +               .impedance = IMP_OUTPUT_DRV_40_OHM,
>> +               .gate_leveling_enable = 1,
>> +       }
>> +};
>> +
>> +/**
>> + * Get the required memory type and speed (SPL version).
>> + *
>> + * In SPL we have no device tree, so we use the machine parameters
>> + *
>> + * @param mem_type     Returns memory type
>> + * @param frequency_mhz        Returns memory speed in MHz
>> + * @param arm_freq     Returns ARM clock speed in MHz
>> + * @param mem_manuf    Return Memory Manufacturer name
>> + * @return 0 if all ok
>> + */
>> +static int clock_get_mem_selection(enum ddr_mode *mem_type,
>> +               unsigned *frequency_mhz, unsigned *arm_freq,
>> +               enum mem_manuf *mem_manuf)
>> +{
>> +       struct spl_machine_param *params;
>> +
>> +       params = spl_get_machine_params();
>> +       *mem_type = params->mem_type;
>> +       *frequency_mhz = params->frequency_mhz;
>> +       *arm_freq = params->arm_freq_mhz;
>> +       *mem_manuf = params->mem_manuf;
>> +
>> +       return 0;
>> +}
>> +
>> +/* Get the ratios for setting ARM clock */
>> +struct arm_clk_ratios *get_arm_ratios(void)
>> +{
>> +       struct arm_clk_ratios *arm_ratio;
>> +       enum ddr_mode mem_type;
>> +       enum mem_manuf mem_manuf;
>> +       unsigned frequency_mhz, arm_freq;
>> +       int i;
>> +
>> +       if (clock_get_mem_selection(&mem_type, &frequency_mhz,
>> +                                       &arm_freq, &mem_manuf))
>> +               ;
>> +       for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
>> +               i++, arm_ratio++) {
>> +               if (arm_ratio->arm_freq_mhz == arm_freq)
>> +                       return arm_ratio;
>> +       }
>> +
>> +       /* will hang if failed to find clock ratio */
>> +       while (1)
>> +               ;
>> +
>> +       return NULL;
>> +}
>> +
>> +struct mem_timings *clock_get_mem_timings(void)
>> +{
>> +       struct mem_timings *mem;
>> +       enum ddr_mode mem_type;
>> +       enum mem_manuf mem_manuf;
>> +       unsigned frequency_mhz, arm_freq;
>> +       int i;
>> +
>> +       if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
>> +                                               &arm_freq, &mem_manuf)) {
>> +               for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
>> +                               i++, mem++) {
>> +                       if (mem->mem_type == mem_type &&
>> +                                       mem->frequency_mhz == frequency_mhz &&
>> +                                       mem->mem_manuf == mem_manuf)
>> +                               return mem;
>> +               }
>> +       }
>> +
>> +       /* will hang if failed to find memory timings */
>> +       while (1)
>> +               ;
>> +
>> +       return NULL;
>> +}
>> +
>> +void system_clock_init()
>> +{
>> +       struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
>> +       struct mem_timings *mem;
>> +       struct arm_clk_ratios *arm_clk_ratio;
>> +       u32 val, tmp;
>> +
>> +       mem = clock_get_mem_timings();
>> +       arm_clk_ratio = get_arm_ratios();
>> +
>> +       clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
>> +       do {
>> +               val = readl(&clk->mux_stat_cpu);
>> +       } while ((val | MUX_APLL_SEL_MASK) != val);
>> +
>> +       clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
>> +       do {
>> +               val = readl(&clk->mux_stat_core1);
>> +       } while ((val | MUX_MPLL_SEL_MASK) != val);
>> +
>> +       clrbits_le32(&clk->src_core1, MUX_CPLL_SEL_MASK);
>> +       clrbits_le32(&clk->src_core1, MUX_EPLL_SEL_MASK);
>> +       clrbits_le32(&clk->src_core1, MUX_VPLL_SEL_MASK);
>> +       clrbits_le32(&clk->src_core1, MUX_GPLL_SEL_MASK);
>> +       tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
>> +               | MUX_GPLL_SEL_MASK;
>> +       do {
>> +               val = readl(&clk->mux_stat_top2);
>> +       } while ((val | tmp) != val);
>> +
>> +       clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
>> +       do {
>> +               val = readl(&clk->mux_stat_cdrex);
>> +       } while ((val | MUX_BPLL_SEL_MASK) != val);
>> +
>> +       /* PLL locktime */
>> +       writel(APLL_LOCK_VAL, &clk->apll_lock);
>> +
>> +       writel(MPLL_LOCK_VAL, &clk->mpll_lock);
>> +
>> +       writel(BPLL_LOCK_VAL, &clk->bpll_lock);
>> +
>> +       writel(CPLL_LOCK_VAL, &clk->cpll_lock);
>> +
>> +       writel(GPLL_LOCK_VAL, &clk->gpll_lock);
>> +
>> +       writel(EPLL_LOCK_VAL, &clk->epll_lock);
>> +
>> +       writel(VPLL_LOCK_VAL, &clk->vpll_lock);
>> +
>> +       writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
>> +
>> +       writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
>> +       do {
>> +               val = readl(&clk->mux_stat_cpu);
>> +       } while ((val | HPM_SEL_SCLK_MPLL) != val);
>> +
>> +       val = arm_clk_ratio->arm2_ratio << 28
>> +               | arm_clk_ratio->apll_ratio << 24
>> +               | arm_clk_ratio->pclk_dbg_ratio << 20
>> +               | arm_clk_ratio->atb_ratio << 16
>> +               | arm_clk_ratio->periph_ratio << 12
>> +               | arm_clk_ratio->acp_ratio << 8
>> +               | arm_clk_ratio->cpud_ratio << 4
>> +               | arm_clk_ratio->arm_ratio;
>> +       writel(val, &clk->div_cpu0);
>> +       do {
>> +               val = readl(&clk->div_stat_cpu0);
>> +       } while (0 != val);
>> +
>> +       writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
>> +       do {
>> +               val = readl(&clk->div_stat_cpu1);
>> +       } while (0 != val);
>> +
>> +       /* Set APLL */
>> +       writel(APLL_CON1_VAL, &clk->apll_con1);
>> +       val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
>> +                       arm_clk_ratio->apll_sdiv);
>> +       writel(val, &clk->apll_con0);
>> +       while (readl(&clk->apll_con0) & APLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set MPLL */
>> +       writel(MPLL_CON1_VAL, &clk->mpll_con1);
>> +       val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
>> +       writel(val, &clk->mpll_con0);
>> +       while (readl(&clk->mpll_con0) & MPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set BPLL */
>> +       writel(BPLL_CON1_VAL, &clk->bpll_con1);
>> +       val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
>> +       writel(val, &clk->bpll_con0);
>> +       while (readl(&clk->bpll_con0) & BPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set CPLL */
>> +       writel(CPLL_CON1_VAL, &clk->cpll_con1);
>> +       val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
>> +       writel(val, &clk->cpll_con0);
>> +       while (readl(&clk->cpll_con0) & CPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set GPLL */
>> +       writel(GPLL_CON1_VAL, &clk->gpll_con1);
>> +       val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
>> +       writel(val, &clk->gpll_con0);
>> +       while (readl(&clk->gpll_con0) & GPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set EPLL */
>> +       writel(EPLL_CON2_VAL, &clk->epll_con2);
>> +       writel(EPLL_CON1_VAL, &clk->epll_con1);
>> +       val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
>> +       writel(val, &clk->epll_con0);
>> +       while (readl(&clk->epll_con0) & EPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       /* Set VPLL */
>> +       writel(VPLL_CON2_VAL, &clk->vpll_con2);
>> +       writel(VPLL_CON1_VAL, &clk->vpll_con1);
>> +       val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
>> +       writel(val, &clk->vpll_con0);
>> +       while (readl(&clk->vpll_con0) & VPLL_CON0_LOCKED)
>> +               ;
>> +
>> +       writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
>> +       writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
>> +       while (readl(&clk->div_stat_core0) != 0)
>> +               ;
>> +
>> +       writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
>> +       while (readl(&clk->div_stat_core1) != 0)
>> +               ;
>> +
>> +       writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
>> +       while (readl(&clk->div_stat_sysrgt) != 0)
>> +               ;
>> +
>> +       writel(CLK_DIV_ACP_VAL, &clk->div_acp);
>> +       while (readl(&clk->div_stat_acp) != 0)
>> +               ;
>> +
>> +       writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
>> +       while (readl(&clk->div_stat_syslft) != 0)
>> +               ;
>> +
>> +       writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
>> +       writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
>> +       writel(TOP2_VAL, &clk->src_top2);
>> +       writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
>> +
>> +       writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
>> +       while (readl(&clk->div_stat_top0))
>> +               ;
>> +
>> +       writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
>> +       while (readl(&clk->div_stat_top1))
>> +               ;
>> +
>> +       writel(CLK_SRC_LEX_VAL, &clk->src_lex);
>> +       while (1) {
>> +               val = readl(&clk->mux_stat_lex);
>> +               if (val == (val | 1))
>> +                       break;
>> +       }
>> +
>> +       writel(CLK_DIV_LEX_VAL, &clk->div_lex);
>> +       while (readl(&clk->div_stat_lex))
>> +               ;
>> +
>> +       writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
>> +       while (readl(&clk->div_stat_r0x))
>> +               ;
>> +
>> +       writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
>> +       while (readl(&clk->div_stat_r0x))
>> +               ;
>> +
>> +       writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
>> +       while (readl(&clk->div_stat_r1x))
>> +               ;
>> +
>> +       writel(CLK_REG_DISABLE, &clk->src_cdrex);
>> +
>> +       writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
>> +       while (readl(&clk->div_stat_cdrex))
>> +               ;
>> +
>> +       val = readl(&clk->src_cpu);
>> +       val |= CLK_SRC_CPU_VAL;
>> +       writel(val, &clk->src_cpu);
>> +
>> +       val = readl(&clk->src_top2);
>> +       val |= CLK_SRC_TOP2_VAL;
>> +       writel(val, &clk->src_top2);
>> +
>> +       val = readl(&clk->src_core1);
>> +       val |= CLK_SRC_CORE1_VAL;
>> +       writel(val, &clk->src_core1);
>> +
>> +       writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
>> +       writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
>> +       while (readl(&clk->div_stat_fsys0))
>> +               ;
>> +
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
>> +       writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
>> +
>> +       writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
>> +       writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
>> +
>> +       writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
>> +       writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
>> +       writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
>> +       writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
>> +
>> +       writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
>> +       writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
>> +       writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
>> +       writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
>> +       writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
>> +
>> +       /* FIMD1 SRC CLK SELECTION */
>> +       writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
>> +
>> +       val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
>> +               | MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
>> +               | MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
>> +               | MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
>> +       writel(val, &clk->div_fsys2);
>> +}
>> diff --git a/board/samsung/arndale/clock_init.h b/board/samsung/arndale/clock_init.h
>> new file mode 100644
>> index 0000000..5d01a6c
>> --- /dev/null
>> +++ b/board/samsung/arndale/clock_init.h
>> @@ -0,0 +1,149 @@
>> +/*
>> + * Clock initialization routines
>> + *
>> + * Copyright (c) 2011 The Chromium OS Authors.
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#ifndef __ARNDALE_CLOCK_INIT_H
>> +#define __ARNDALE_CLOCK_INIT_H
>> +
>> +enum {
>> +       MEM_TIMINGS_MSR_COUNT   = 4,
>> +};
>> +
>> +/* These are the ratio's for configuring ARM clock */
>> +struct arm_clk_ratios {
>> +       unsigned arm_freq_mhz;          /* Frequency of ARM core in MHz */
>> +
>> +       unsigned apll_mdiv;
>> +       unsigned apll_pdiv;
>> +       unsigned apll_sdiv;
>> +
>> +       unsigned arm2_ratio;
>> +       unsigned apll_ratio;
>> +       unsigned pclk_dbg_ratio;
>> +       unsigned atb_ratio;
>> +       unsigned periph_ratio;
>> +       unsigned acp_ratio;
>> +       unsigned cpud_ratio;
>> +       unsigned arm_ratio;
>> +};
>> +
>> +/* These are the memory timings for a particular memory type and speed */
>> +struct mem_timings {
>> +       enum mem_manuf mem_manuf;       /* Memory manufacturer */
>> +       enum ddr_mode mem_type;         /* Memory type */
>> +       unsigned frequency_mhz;         /* Frequency of memory in MHz */
>> +
>> +       /* Here follow the timing parameters for the selected memory */
>> +       unsigned apll_mdiv;
>> +       unsigned apll_pdiv;
>> +       unsigned apll_sdiv;
>> +       unsigned mpll_mdiv;
>> +       unsigned mpll_pdiv;
>> +       unsigned mpll_sdiv;
>> +       unsigned cpll_mdiv;
>> +       unsigned cpll_pdiv;
>> +       unsigned cpll_sdiv;
>> +       unsigned gpll_mdiv;
>> +       unsigned gpll_pdiv;
>> +       unsigned gpll_sdiv;
>> +       unsigned epll_mdiv;
>> +       unsigned epll_pdiv;
>> +       unsigned epll_sdiv;
>> +       unsigned vpll_mdiv;
>> +       unsigned vpll_pdiv;
>> +       unsigned vpll_sdiv;
>> +       unsigned bpll_mdiv;
>> +       unsigned bpll_pdiv;
>> +       unsigned bpll_sdiv;
>> +       unsigned pclk_cdrex_ratio;
>> +       unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
>> +
>> +       unsigned timing_ref;
>> +       unsigned timing_row;
>> +       unsigned timing_data;
>> +       unsigned timing_power;
>> +
>> +       /* DQS, DQ, DEBUG offsets */
>> +       unsigned phy0_dqs;
>> +       unsigned phy1_dqs;
>> +       unsigned phy0_dq;
>> +       unsigned phy1_dq;
>> +       unsigned phy0_tFS;
>> +       unsigned phy1_tFS;
>> +       unsigned phy0_pulld_dqs;
>> +       unsigned phy1_pulld_dqs;
>> +
>> +       unsigned lpddr3_ctrl_phy_reset;
>> +       unsigned ctrl_start_point;
>> +       unsigned ctrl_inc;
>> +       unsigned ctrl_start;
>> +       unsigned ctrl_dll_on;
>> +       unsigned ctrl_ref;
>> +
>> +       unsigned ctrl_force;
>> +       unsigned ctrl_rdlat;
>> +       unsigned ctrl_bstlen;
>> +
>> +       unsigned fp_resync;
>> +       unsigned iv_size;
>> +       unsigned dfi_init_start;
>> +       unsigned aref_en;
>> +
>> +       unsigned rd_fetch;
>> +
>> +       unsigned zq_mode_dds;
>> +       unsigned zq_mode_term;
>> +       unsigned zq_mode_noterm;        /* 1 to allow termination disable */
>> +
>> +       unsigned memcontrol;
>> +       unsigned memconfig;
>> +
>> +       unsigned membaseconfig0;
>> +       unsigned membaseconfig1;
>> +       unsigned prechconfig_tp_cnt;
>> +       unsigned dpwrdn_cyc;
>> +       unsigned dsref_cyc;
>> +       unsigned concontrol;
>> +       /* Channel and Chip Selection */
>> +       uint8_t dmc_channels;           /* number of memory channels */
>> +       uint8_t chips_per_channel;      /* number of chips per channel */
>> +       uint8_t chips_to_configure;     /* number of chips to configure */
>> +       uint8_t send_zq_init;           /* 1 to send this command */
>> +       unsigned impedance;             /* drive strength impedeance */
>> +       uint8_t gate_leveling_enable;   /* check gate leveling is enabled */
>> +};
>> +
>> +/**
>> + * Get the correct memory timings for our selected memory type and speed.
>> + *
>> + * This function can be called from SPL or the main U-Boot.
>> + *
>> + * @return pointer to the memory timings that we should use
>> + */
>> +struct mem_timings *clock_get_mem_timings(void);
>> +
>> +/*
>> + * Initialize clock for the device
>> + */
>> +void system_clock_init(void);
>> +#endif
>> diff --git a/board/samsung/arndale/dmc_common.c b/board/samsung/arndale/dmc_common.c
>> new file mode 100644
>> index 0000000..5a51def
>> --- /dev/null
>> +++ b/board/samsung/arndale/dmc_common.c
>> @@ -0,0 +1,199 @@
>> +/*
>> + * Mem setup common file for different types of DDR present on Arndale boards.
>> + *
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <common.h>
>> +#include <asm/arch/spl.h>
>> +
>> +#include "clock_init.h"
>> +#include "setup.h"
>> +
>> +#define ZQ_INIT_TIMEOUT        10000
>> +
>> +int dmc_config_zq(struct mem_timings *mem,
>> +                 struct exynos5_phy_control *phy0_ctrl,
>> +                 struct exynos5_phy_control *phy1_ctrl)
>> +{
>> +       unsigned long val = 0;
>> +       int i;
>> +
>> +       /*
>> +        * ZQ Calibration:
>> +        * Select Driver Strength,
>> +        * long calibration for manual calibration
>> +        */
>> +       val = PHY_CON16_RESET_VAL;
>> +       val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
>> +       val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
>> +       val |= ZQ_CLK_DIV_EN;
>> +       writel(val, &phy0_ctrl->phy_con16);
>> +       writel(val, &phy1_ctrl->phy_con16);
>> +
>> +       /* Disable termination */
>> +       if (mem->zq_mode_noterm)
>> +               val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
>> +       writel(val, &phy0_ctrl->phy_con16);
>> +       writel(val, &phy1_ctrl->phy_con16);
>> +
>> +       /* ZQ_MANUAL_START: Enable */
>> +       val |= ZQ_MANUAL_STR;
>> +       writel(val, &phy0_ctrl->phy_con16);
>> +       writel(val, &phy1_ctrl->phy_con16);
>> +
>> +       /* ZQ_MANUAL_START: Disable */
>> +       val &= ~ZQ_MANUAL_STR;
>> +
>> +       /*
>> +        * Since we are manaully calibrating the ZQ values,
>> +        * we are looping for the ZQ_init to complete.
>> +        */
>> +       i = ZQ_INIT_TIMEOUT;
>> +       while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
>> +               sdelay(100);
>> +               i--;
>> +       }
>> +       if (!i)
>> +               return -1;
>> +       writel(val, &phy0_ctrl->phy_con16);
>> +
>> +       i = ZQ_INIT_TIMEOUT;
>> +       while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
>> +               sdelay(100);
>> +               i--;
>> +       }
>> +       if (!i)
>> +               return -1;
>> +       writel(val, &phy1_ctrl->phy_con16);
>> +
>> +       return 0;
>> +}
>> +
>> +void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
>> +{
>> +       unsigned long val;
>> +
>> +       if (mode == DDR_MODE_DDR3) {
>> +               val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
>> +               writel(val, &dmc->phycontrol0);
>> +       }
>> +
>> +       /* Update DLL Information: Force DLL Resyncronization */
>> +       val = readl(&dmc->phycontrol0);
>> +       val |= FP_RSYNC;
>> +       writel(val, &dmc->phycontrol0);
>> +
>> +       /* Reset Force DLL Resyncronization */
>> +       val = readl(&dmc->phycontrol0);
>> +       val &= ~FP_RSYNC;
>> +       writel(val, &dmc->phycontrol0);
>> +}
>> +
>> +void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
>> +{
>> +       int channel, chip;
>> +
>> +       for (channel = 0; channel < mem->dmc_channels; channel++) {
>> +               unsigned long mask;
>> +
>> +               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
>> +               for (chip = 0; chip < mem->chips_to_configure; chip++) {
>> +                       int i;
>> +
>> +                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
>> +
>> +                       /* Sending NOP command */
>> +                       writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
>> +
>> +                       /*
>> +                        * TODO(alim.akhtar@samsung.com): Do we need these
>> +                        * delays? This one and the next were not there for
>> +                        * DDR3.
>> +                        */
>> +                       sdelay(0x10000);
>> +
>> +                       /* Sending EMRS/MRS commands */
>> +                       for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
>> +                               writel(mem->direct_cmd_msr[i] | mask,
>> +                                      &dmc->directcmd);
>> +                               sdelay(0x10000);
>> +                       }
>> +
>> +                       if (mem->send_zq_init) {
>> +                               /* Sending ZQINIT command */
>> +                               writel(DIRECT_CMD_ZQINIT | mask,
>> +                                      &dmc->directcmd);
>> +
>> +                               sdelay(10000);
>> +                       }
>> +               }
>> +       }
>> +}
>> +
>> +void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
>> +{
>> +       int channel, chip;
>> +
>> +       for (channel = 0; channel < mem->dmc_channels; channel++) {
>> +               unsigned long mask;
>> +
>> +               mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
>> +               for (chip = 0; chip < mem->chips_per_channel; chip++) {
>> +                       mask |= chip << DIRECT_CMD_CHIP_SHIFT;
>> +
>> +                       /* PALL (all banks precharge) CMD */
>> +                       writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
>> +                       sdelay(0x10000);
>> +               }
>> +       }
>> +}
>> +
>> +void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
>> +{
>> +       writel(mem->memconfig, &dmc->memconfig0);
>> +       writel(mem->memconfig, &dmc->memconfig1);
>> +       writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
>> +       writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
>> +}
>> +
>> +void mem_ctrl_init()
>> +{
>> +       struct spl_machine_param *param = spl_get_machine_params();
>> +       struct mem_timings *mem;
>> +       int ret;
>> +
>> +       mem = clock_get_mem_timings();
>> +
>> +       /* If there are any other memory variant, add their init call below */
>> +       if (param->mem_type == DDR_MODE_DDR3) {
>> +               ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size);
>> +               if (ret) {
>> +                       /* will hang if failed to init memory control */
>> +                       while (1)
>> +                               ;
>> +               }
>> +       } else {
>> +               /* will hang if unknow memory type  */
>> +               while (1)
>> +                       ;
>> +       }
>> +}
>> diff --git a/board/samsung/arndale/dmc_init_ddr3.c b/board/samsung/arndale/dmc_init_ddr3.c
>> new file mode 100644
>> index 0000000..ce91451
>> --- /dev/null
>> +++ b/board/samsung/arndale/dmc_init_ddr3.c
>> @@ -0,0 +1,228 @@
>> +/*
>> + * DDR3 mem setup file for Arndale board based on EXYNOS5
>> + *
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <config.h>
>> +#include <asm/io.h>
>> +#include <asm/arch/clock.h>
>> +#include <asm/arch/cpu.h>
>> +#include <asm/arch/dmc.h>
>> +#include "setup.h"
>> +#include "clock_init.h"
>> +
>> +#define RDLVL_COMPLETE_TIMEOUT 10000
>> +
>> +static void reset_phy_ctrl(void)
>> +{
>> +       struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
>> +
>> +       writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
>> +       writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
>> +}
>> +
>> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
>> +{
>> +       unsigned int val;
>> +       struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
>> +       struct exynos5_dmc *dmc;
>> +       int i;
>> +
>> +       phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
>> +       phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
>> +       dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
>> +
>> +       reset_phy_ctrl();
>> +
>> +       /* Set Impedance Output Driver */
>> +       val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
>> +               (mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
>> +               (mem->impedance << CA_CS_DRVR_DS_OFFSET) |
>> +               (mem->impedance << CA_ADR_DRVR_DS_OFFSET);
>> +       writel(val, &phy0_ctrl->phy_con39);
>> +       writel(val, &phy1_ctrl->phy_con39);
>> +
>> +       /* Set Read Latency and Burst Length for PHY0 and PHY1 */
>> +       val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
>> +               (mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
>> +       writel(val, &phy0_ctrl->phy_con42);
>> +       writel(val, &phy1_ctrl->phy_con42);
>> +
>> +       /* ZQ Calibration */
>> +       if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
>> +               return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
>> +
>> +       /* DQ Signal */
>> +       writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
>> +       writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
>> +
>> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
>> +               | (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
>> +               &dmc->concontrol);
>> +
>> +       update_reset_dll(dmc, DDR_MODE_DDR3);
>> +
>> +       /* DQS Signal */
>> +       writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
>> +       writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
>> +
>> +       writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
>> +       writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
>> +
>> +       writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
>> +       writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
>> +
>> +       val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
>> +               (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
>> +               (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
>> +               (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
>> +       writel(val, &phy0_ctrl->phy_con12);
>> +       writel(val, &phy1_ctrl->phy_con12);
>> +
>> +       /* Start DLL locking */
>> +       writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
>> +               &phy0_ctrl->phy_con12);
>> +       writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
>> +               &phy1_ctrl->phy_con12);
>> +
>> +       update_reset_dll(dmc, DDR_MODE_DDR3);
>> +
>> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
>> +               &dmc->concontrol);
>> +
>> +       /* Memory Channel Inteleaving Size */
>> +       writel(mem->iv_size, &dmc->ivcontrol);
>> +
>> +       writel(mem->memconfig, &dmc->memconfig0);
>> +       writel(mem->memconfig, &dmc->memconfig1);
>> +       writel(mem->membaseconfig0, &dmc->membaseconfig0);
>> +       writel(mem->membaseconfig1, &dmc->membaseconfig1);
>> +
>> +       /* Precharge Configuration */
>> +       writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
>> +               &dmc->prechconfig);
>> +
>> +       /* Power Down mode Configuration */
>> +       writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
>> +               mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
>> +               &dmc->pwrdnconfig);
>> +
>> +       /* TimingRow, TimingData, TimingPower and Timingaref
>> +        * values as per Memory AC parameters
>> +        */
>> +       writel(mem->timing_ref, &dmc->timingref);
>> +       writel(mem->timing_row, &dmc->timingrow);
>> +       writel(mem->timing_data, &dmc->timingdata);
>> +       writel(mem->timing_power, &dmc->timingpower);
>> +
>> +       /* Send PALL command */
>> +       dmc_config_prech(mem, dmc);
>> +
>> +       /* Send NOP, MRS and ZQINIT commands */
>> +       dmc_config_mrs(mem, dmc);
>> +
>> +       if (mem->gate_leveling_enable) {
>> +               val = PHY_CON0_RESET_VAL;
>> +               val |= P0_CMD_EN;
>> +               writel(val, &phy0_ctrl->phy_con0);
>> +               writel(val, &phy1_ctrl->phy_con0);
>> +
>> +               val = PHY_CON2_RESET_VAL;
>> +               val |= INIT_DESKEW_EN;
>> +               writel(val, &phy0_ctrl->phy_con2);
>> +               writel(val, &phy1_ctrl->phy_con2);
>> +
>> +               val = PHY_CON0_RESET_VAL;
>> +               val |= P0_CMD_EN;
>> +               val |= BYTE_RDLVL_EN;
>> +               writel(val, &phy0_ctrl->phy_con0);
>> +               writel(val, &phy1_ctrl->phy_con0);
>> +
>> +               val = (mem->ctrl_start_point <<
>> +                               PHY_CON12_CTRL_START_POINT_SHIFT) |
>> +                       (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
>> +                       (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
>> +                       (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
>> +                       (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
>> +               writel(val, &phy0_ctrl->phy_con12);
>> +               writel(val, &phy1_ctrl->phy_con12);
>> +
>> +               val = PHY_CON2_RESET_VAL;
>> +               val |= INIT_DESKEW_EN;
>> +               val |= RDLVL_GATE_EN;
>> +               writel(val, &phy0_ctrl->phy_con2);
>> +               writel(val, &phy1_ctrl->phy_con2);
>> +
>> +               val = PHY_CON0_RESET_VAL;
>> +               val |= P0_CMD_EN;
>> +               val |= BYTE_RDLVL_EN;
>> +               val |= CTRL_SHGATE;
>> +               writel(val, &phy0_ctrl->phy_con0);
>> +               writel(val, &phy1_ctrl->phy_con0);
>> +
>> +               val = PHY_CON1_RESET_VAL;
>> +               val &= ~(CTRL_GATEDURADJ_MASK);
>> +               writel(val, &phy0_ctrl->phy_con1);
>> +               writel(val, &phy1_ctrl->phy_con1);
>> +
>> +               writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
>> +               i = RDLVL_COMPLETE_TIMEOUT;
>> +               while ((readl(&dmc->phystatus) &
>> +                       (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
>> +                       (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
>> +                       /*
>> +                        * TODO(waihong): Comment on how long this take to
>> +                        * timeout
>> +                        */
>> +                       sdelay(100);
>> +                       i--;
>> +               }
>> +               if (!i)
>> +                       return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
>> +               writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
>> +
>> +               writel(0, &phy0_ctrl->phy_con14);
>> +               writel(0, &phy1_ctrl->phy_con14);
>> +
>> +               val = (mem->ctrl_start_point <<
>> +                               PHY_CON12_CTRL_START_POINT_SHIFT) |
>> +                       (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
>> +                       (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
>> +                       (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
>> +                       (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
>> +                       (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
>> +               writel(val, &phy0_ctrl->phy_con12);
>> +               writel(val, &phy1_ctrl->phy_con12);
>> +
>> +               update_reset_dll(dmc, DDR_MODE_DDR3);
>> +       }
>> +
>> +       /* Send PALL command */
>> +       dmc_config_prech(mem, dmc);
>> +
>> +       writel(mem->memcontrol, &dmc->memcontrol);
>> +
>> +       /* Set DMC Concontrol and enable auto-refresh counter */
>> +       writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
>> +               | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
>> +       return 0;
>> +}
>> diff --git a/board/samsung/arndale/lowlevel_init.S b/board/samsung/arndale/lowlevel_init.S
>> new file mode 100644
>> index 0000000..4fa73a7
>> --- /dev/null
>> +++ b/board/samsung/arndale/lowlevel_init.S
>> @@ -0,0 +1,92 @@
>> +/*
>> + * Lowlevel setup for Arndale board based on Exynos5
>> + *
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#include <config.h>
>> +#include <version.h>
>> +#include <asm/arch/cpu.h>
>> +
>> +_TEXT_BASE:
>> +       .word   CONFIG_SYS_TEXT_BASE
>> +
>> +       .globl lowlevel_init
>> +lowlevel_init:
>> +
>> +       /* use iRAM stack in bl2 */
>> +       ldr     sp, =CONFIG_IRAM_STACK
>> +       stmdb   r13!, {ip,lr}
>> +
>> +       /* check reset status */
>> +       ldr     r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET)
>> +       ldr     r1, [r0]
>> +
>> +       /* AFTR wakeup reset */
>> +       ldr     r2, =S5P_CHECK_DIDLE
>> +       cmp     r1, r2
>> +       beq     exit_wakeup
>> +
>> +       /* Sleep wakeup reset */
>> +       ldr     r2, =S5P_CHECK_SLEEP
>> +       cmp     r1, r2
>> +       beq     wakeup_reset
>> +
>> +       /*
>> +        * If U-boot is already running in RAM, no need to relocate U-Boot.
>> +        * Memory controller must be configured before relocating U-Boot
>> +        * in ram.
>> +        */
>> +       ldr     r0, =0x0ffffff          /* r0 <- Mask Bits*/
>> +       bic     r1, pc, r0              /* pc <- current addr of code */
>> +                                       /* r1 <- unmasked bits of pc */
>> +       ldr     r2, _TEXT_BASE          /* r2 <- original base addr in ram */
>> +       bic     r2, r2, r0              /* r2 <- unmasked bits of r2*/
>> +       cmp     r1, r2                  /* compare r1, r2 */
>> +       beq     1f                      /* r0 == r1 then skip sdram init */
>> +
>> +       /* init system clock */
>> +       bl      system_clock_init
>> +
>> +       /* Memory initialize */
>> +       bl      mem_ctrl_init
>> +1:
>> +       bl      arch_cpu_init
>> +       bl      tzpc_init
>> +       ldmia   r13!, {ip,pc}
>> +
>> +wakeup_reset:
>> +       bl      system_clock_init
>> +       bl      mem_ctrl_init
>> +       bl      arch_cpu_init
>> +       bl      tzpc_init
>> +
>> +exit_wakeup:
>> +       /* Load return address and jump to kernel */
>> +       ldr     r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET)
>> +
>> +       /* r1 = physical address of exynos5_cpu_resume function*/
>> +       ldr     r1, [r0]
>> +
>> +       /* Jump to kernel */
>> +       mov     pc, r1
>> +       nop
>> +       nop
>> diff --git a/board/samsung/arndale/setup.h b/board/samsung/arndale/setup.h
>> new file mode 100644
>> index 0000000..f68dd75
>> --- /dev/null
>> +++ b/board/samsung/arndale/setup.h
>> @@ -0,0 +1,569 @@
>> +/*
>> + * Machine Specific Values for Arndale board based on EXYNOS5
>> + *
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#ifndef _ARNDALE_SETUP_H
>> +#define _ARNDALE_SETUP_H
>> +
>> +#include <config.h>
>> +#include <asm/arch/dmc.h>
>> +
>> +/* APLL_CON1   */
>> +#define APLL_CON1_VAL  (0x00203800)
>> +
>> +/* MPLL_CON1   */
>> +#define MPLL_CON1_VAL   (0x00203800)
>> +
>> +/* CPLL_CON1   */
>> +#define CPLL_CON1_VAL  (0x00203800)
>> +
>> +/* GPLL_CON1   */
>> +#define GPLL_CON1_VAL  (0x00203800)
>> +
>> +/* EPLL_CON1, CON2     */
>> +#define EPLL_CON1_VAL  0x00000000
>> +#define EPLL_CON2_VAL  0x00000080
>> +
>> +/* VPLL_CON1, CON2     */
>> +#define VPLL_CON1_VAL  0x00000000
>> +#define VPLL_CON2_VAL  0x00000080
>> +
>> +/* BPLL_CON1   */
>> +#define BPLL_CON1_VAL  0x00203800
>> +
>> +/* Set PLL */
>> +#define set_pll(mdiv, pdiv, sdiv)      (1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
>> +
>> +/* CLK_SRC_CPU */
>> +/* 0 = MOUTAPLL,  1 = SCLKMPLL */
>> +#define MUX_HPM_SEL             0
>> +#define MUX_CPU_SEL             0
>> +#define MUX_APLL_SEL            1
>> +
>> +#define CLK_SRC_CPU_VAL                ((MUX_HPM_SEL << 20)    \
>> +                               | (MUX_CPU_SEL << 16)  \
>> +                               | (MUX_APLL_SEL))
>> +
>> +/* MEMCONTROL register bit fields */
>> +#define DMC_MEMCONTROL_CLK_STOP_DISABLE        (0 << 0)
>> +#define DMC_MEMCONTROL_DPWRDN_DISABLE  (0 << 1)
>> +#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
>> +#define DMC_MEMCONTROL_TP_DISABLE      (0 << 4)
>> +#define DMC_MEMCONTROL_DSREF_DISABLE   (0 << 5)
>> +#define DMC_MEMCONTROL_DSREF_ENABLE    (1 << 5)
>> +#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x)    (x << 6)
>> +
>> +#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3  (7 << 8)
>> +#define DMC_MEMCONTROL_MEM_TYPE_DDR3    (6 << 8)
>> +#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2  (5 << 8)
>> +
>> +#define DMC_MEMCONTROL_MEM_WIDTH_32BIT  (2 << 12)
>> +
>> +#define DMC_MEMCONTROL_NUM_CHIP_1       (0 << 16)
>> +#define DMC_MEMCONTROL_NUM_CHIP_2       (1 << 16)
>> +
>> +#define DMC_MEMCONTROL_BL_8             (3 << 20)
>> +#define DMC_MEMCONTROL_BL_4             (2 << 20)
>> +
>> +#define DMC_MEMCONTROL_PZQ_DISABLE      (0 << 24)
>> +
>> +#define DMC_MEMCONTROL_MRR_BYTE_7_0     (0 << 25)
>> +#define DMC_MEMCONTROL_MRR_BYTE_15_8    (1 << 25)
>> +#define DMC_MEMCONTROL_MRR_BYTE_23_16   (2 << 25)
>> +#define DMC_MEMCONTROL_MRR_BYTE_31_24   (3 << 25)
>> +
>> +/* MEMCONFIG0 register bit fields */
>> +#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED     (1 << 12)
>> +#define DMC_MEMCONFIGx_CHIP_COL_10              (3 << 8)
>> +#define DMC_MEMCONFIGx_CHIP_ROW_14              (2 << 4)
>> +#define DMC_MEMCONFIGx_CHIP_ROW_15              (3 << 4)
>> +#define DMC_MEMCONFIGx_CHIP_BANK_8              (3 << 0)
>> +
>> +#define DMC_MEMBASECONFIGx_CHIP_BASE(x)         (x << 16)
>> +#define DMC_MEMBASECONFIGx_CHIP_MASK(x)         (x << 0)
>> +#define DMC_MEMBASECONFIG_VAL(x)        (       \
>> +       DMC_MEMBASECONFIGx_CHIP_BASE(x) |       \
>> +       DMC_MEMBASECONFIGx_CHIP_MASK(0x780)     \
>> +)
>> +
>> +#define DMC_MEMBASECONFIG0_VAL  DMC_MEMBASECONFIG_VAL(0x40)
>> +#define DMC_MEMBASECONFIG1_VAL  DMC_MEMBASECONFIG_VAL(0x80)
>> +
>> +#define DMC_PRECHCONFIG_VAL             0xFF000000
>> +#define DMC_PWRDNCONFIG_VAL             0xFFFF00FF
>> +
>> +#define DMC_CONCONTROL_RESET_VAL       0x0FFF0000
>> +#define DFI_INIT_START         (1 << 28)
>> +#define EMPTY                  (1 << 8)
>> +#define AREF_EN                        (1 << 5)
>> +
>> +#define DFI_INIT_COMPLETE_CHO  (1 << 2)
>> +#define DFI_INIT_COMPLETE_CH1  (1 << 3)
>> +
>> +#define RDLVL_COMPLETE_CHO     (1 << 14)
>> +#define RDLVL_COMPLETE_CH1     (1 << 15)
>> +
>> +#define CLK_STOP_EN    (1 << 0)
>> +#define DPWRDN_EN      (1 << 1)
>> +#define DSREF_EN       (1 << 5)
>> +
>> +/* COJCONTROL register bit fields */
>> +#define DMC_CONCONTROL_IO_PD_CON_DISABLE       (0 << 3)
>> +#define DMC_CONCONTROL_AREF_EN_DISABLE         (0 << 5)
>> +#define DMC_CONCONTROL_EMPTY_DISABLE           (0 << 8)
>> +#define DMC_CONCONTROL_EMPTY_ENABLE            (1 << 8)
>> +#define DMC_CONCONTROL_RD_FETCH_DISABLE                (0x0 << 12)
>> +#define DMC_CONCONTROL_TIMEOUT_LEVEL0          (0xFFF << 16)
>> +#define DMC_CONCONTROL_DFI_INIT_START_DISABLE  (0 << 28)
>> +
>> +/* CLK_DIV_CPU0_VAL */
>> +#define CLK_DIV_CPU0_VAL       ((ARM2_RATIO << 28)             \
>> +                               | (APLL_RATIO << 24)            \
>> +                               | (PCLK_DBG_RATIO << 20)        \
>> +                               | (ATB_RATIO << 16)             \
>> +                               | (PERIPH_RATIO << 12)          \
>> +                               | (ACP_RATIO << 8)              \
>> +                               | (CPUD_RATIO << 4)             \
>> +                               | (ARM_RATIO))
>> +
>> +
>> +/* CLK_FSYS */
>> +#define CLK_SRC_FSYS0_VAL              0x66666
>> +#define CLK_DIV_FSYS0_VAL             0x0BB00000
>> +
>> +/* CLK_DIV_CPU1        */
>> +#define HPM_RATIO               0x2
>> +#define COPY_RATIO              0x0
>> +
>> +/* CLK_DIV_CPU1 = 0x00000003 */
>> +#define CLK_DIV_CPU1_VAL        ((HPM_RATIO << 4)              \
>> +                               | (COPY_RATIO))
>> +
>> +/* CLK_SRC_CORE0 */
>> +#define CLK_SRC_CORE0_VAL       0x00000000
>> +
>> +/* CLK_SRC_CORE1 */
>> +#define CLK_SRC_CORE1_VAL       0x100
>> +
>> +/* CLK_DIV_CORE0 */
>> +#define CLK_DIV_CORE0_VAL       0x00120000
>> +
>> +/* CLK_DIV_CORE1 */
>> +#define CLK_DIV_CORE1_VAL       0x07070700
>> +
>> +/* CLK_DIV_SYSRGT */
>> +#define CLK_DIV_SYSRGT_VAL      0x00000111
>> +
>> +/* CLK_DIV_ACP */
>> +#define CLK_DIV_ACP_VAL         0x12
>> +
>> +/* CLK_DIV_SYSLFT */
>> +#define CLK_DIV_SYSLFT_VAL      0x00000311
>> +
>> +/* CLK_SRC_CDREX */
>> +#define CLK_SRC_CDREX_VAL       0x1
>> +
>> +/* CLK_DIV_CDREX */
>> +#define MCLK_CDREX2_RATIO       0x0
>> +#define ACLK_EFCON_RATIO        0x1
>> +#define MCLK_DPHY_RATIO                0x1
>> +#define MCLK_CDREX_RATIO       0x1
>> +#define ACLK_C2C_200_RATIO     0x1
>> +#define C2C_CLK_400_RATIO      0x1
>> +#define PCLK_CDREX_RATIO       0x1
>> +#define ACLK_CDREX_RATIO       0x1
>> +
>> +#define CLK_DIV_CDREX_VAL      ((MCLK_DPHY_RATIO << 24)        \
>> +                               | (C2C_CLK_400_RATIO << 6)      \
>> +                               | (PCLK_CDREX_RATIO << 4)       \
>> +                               | (ACLK_CDREX_RATIO))
>> +
>> +/* CLK_SRC_TOP0        */
>> +#define MUX_ACLK_300_GSCL_SEL           0x0
>> +#define MUX_ACLK_300_GSCL_MID_SEL       0x0
>> +#define MUX_ACLK_400_G3D_MID_SEL        0x0
>> +#define MUX_ACLK_333_SEL               0x0
>> +#define MUX_ACLK_300_DISP1_SEL         0x0
>> +#define MUX_ACLK_300_DISP1_MID_SEL      0x0
>> +#define MUX_ACLK_200_SEL               0x0
>> +#define MUX_ACLK_166_SEL               0x0
>> +#define CLK_SRC_TOP0_VAL       ((MUX_ACLK_300_GSCL_SEL  << 25)         \
>> +                               | (MUX_ACLK_300_GSCL_MID_SEL << 24)     \
>> +                               | (MUX_ACLK_400_G3D_MID_SEL << 20)      \
>> +                               | (MUX_ACLK_333_SEL << 16)              \
>> +                               | (MUX_ACLK_300_DISP1_SEL << 15)        \
>> +                               | (MUX_ACLK_300_DISP1_MID_SEL << 14)    \
>> +                               | (MUX_ACLK_200_SEL << 12)              \
>> +                               | (MUX_ACLK_166_SEL << 8))
>> +
>> +/* CLK_SRC_TOP1        */
>> +#define MUX_ACLK_400_G3D_SEL            0x1
>> +#define MUX_ACLK_400_ISP_SEL            0x0
>> +#define MUX_ACLK_400_IOP_SEL            0x0
>> +#define MUX_ACLK_MIPI_HSI_TXBASE_SEL    0x0
>> +#define MUX_ACLK_300_GSCL_MID1_SEL      0x0
>> +#define MUX_ACLK_300_DISP1_MID1_SEL     0x0
>> +#define CLK_SRC_TOP1_VAL       ((MUX_ACLK_400_G3D_SEL << 28)           \
>> +                               |(MUX_ACLK_400_ISP_SEL << 24)           \
>> +                               |(MUX_ACLK_400_IOP_SEL << 20)           \
>> +                               |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16)   \
>> +                               |(MUX_ACLK_300_GSCL_MID1_SEL << 12)     \
>> +                               |(MUX_ACLK_300_DISP1_MID1_SEL << 8))
>> +
>> +/* CLK_SRC_TOP2 */
>> +#define MUX_GPLL_SEL                    0x1
>> +#define MUX_BPLL_USER_SEL               0x0
>> +#define MUX_MPLL_USER_SEL               0x0
>> +#define MUX_VPLL_SEL                    0x1
>> +#define MUX_EPLL_SEL                    0x1
>> +#define MUX_CPLL_SEL                    0x1
>> +#define VPLLSRC_SEL                     0x0
>> +#define CLK_SRC_TOP2_VAL       ((MUX_GPLL_SEL << 28)           \
>> +                               | (MUX_BPLL_USER_SEL << 24)     \
>> +                               | (MUX_MPLL_USER_SEL << 20)     \
>> +                               | (MUX_VPLL_SEL << 16)          \
>> +                               | (MUX_EPLL_SEL << 12)          \
>> +                               | (MUX_CPLL_SEL << 8)           \
>> +                               | (VPLLSRC_SEL))
>> +/* CLK_SRC_TOP3 */
>> +#define MUX_ACLK_333_SUB_SEL            0x1
>> +#define MUX_ACLK_400_SUB_SEL            0x1
>> +#define MUX_ACLK_266_ISP_SUB_SEL        0x1
>> +#define MUX_ACLK_266_GPS_SUB_SEL        0x0
>> +#define MUX_ACLK_300_GSCL_SUB_SEL       0x1
>> +#define MUX_ACLK_266_GSCL_SUB_SEL       0x1
>> +#define MUX_ACLK_300_DISP1_SUB_SEL      0x1
>> +#define MUX_ACLK_200_DISP1_SUB_SEL      0x1
>> +#define CLK_SRC_TOP3_VAL       ((MUX_ACLK_333_SUB_SEL << 24)           \
>> +                               | (MUX_ACLK_400_SUB_SEL << 20)          \
>> +                               | (MUX_ACLK_266_ISP_SUB_SEL << 16)      \
>> +                               | (MUX_ACLK_266_GPS_SUB_SEL << 12)      \
>> +                               | (MUX_ACLK_300_GSCL_SUB_SEL << 10)     \
>> +                               | (MUX_ACLK_266_GSCL_SUB_SEL << 8)      \
>> +                               | (MUX_ACLK_300_DISP1_SUB_SEL << 6)     \
>> +                               | (MUX_ACLK_200_DISP1_SUB_SEL << 4))
>> +
>> +/* CLK_DIV_TOP0        */
>> +#define ACLK_300_DISP1_RATIO   0x2
>> +#define ACLK_400_G3D_RATIO     0x0
>> +#define ACLK_333_RATIO         0x0
>> +#define ACLK_266_RATIO         0x2
>> +#define ACLK_200_RATIO         0x3
>> +#define ACLK_166_RATIO         0x1
>> +#define ACLK_133_RATIO         0x1
>> +#define ACLK_66_RATIO          0x5
>> +
>> +#define CLK_DIV_TOP0_VAL       ((ACLK_300_DISP1_RATIO << 28)   \
>> +                               | (ACLK_400_G3D_RATIO << 24)    \
>> +                               | (ACLK_333_RATIO  << 20)       \
>> +                               | (ACLK_266_RATIO << 16)        \
>> +                               | (ACLK_200_RATIO << 12)        \
>> +                               | (ACLK_166_RATIO << 8)         \
>> +                               | (ACLK_133_RATIO << 4)         \
>> +                               | (ACLK_66_RATIO))
>> +
>> +/* CLK_DIV_TOP1        */
>> +#define ACLK_MIPI_HSI_TX_BASE_RATIO     0x3
>> +#define ACLK_66_PRE_RATIO               0x1
>> +#define ACLK_400_ISP_RATIO              0x1
>> +#define ACLK_400_IOP_RATIO              0x1
>> +#define ACLK_300_GSCL_RATIO             0x2
>> +
>> +#define CLK_DIV_TOP1_VAL       ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28)    \
>> +                               | (ACLK_66_PRE_RATIO << 24)             \
>> +                               | (ACLK_400_ISP_RATIO  << 20)           \
>> +                               | (ACLK_400_IOP_RATIO << 16)            \
>> +                               | (ACLK_300_GSCL_RATIO << 12))
>> +
>> +/* APLL_LOCK   */
>> +#define APLL_LOCK_VAL  (0x546)
>> +/* MPLL_LOCK   */
>> +#define MPLL_LOCK_VAL  (0x546)
>> +/* CPLL_LOCK   */
>> +#define CPLL_LOCK_VAL  (0x546)
>> +/* GPLL_LOCK   */
>> +#define GPLL_LOCK_VAL  (0x546)
>> +/* EPLL_LOCK   */
>> +#define EPLL_LOCK_VAL  (0x3A98)
>> +/* VPLL_LOCK   */
>> +#define VPLL_LOCK_VAL  (0x3A98)
>> +/* BPLL_LOCK   */
>> +#define BPLL_LOCK_VAL  (0x546)
>> +
>> +#define MUX_APLL_SEL_MASK      (1 << 0)
>> +#define MUX_MPLL_SEL_MASK      (1 << 8)
>> +#define MPLL_SEL_MOUT_MPLLFOUT (2 << 8)
>> +#define MUX_CPLL_SEL_MASK      (1 << 8)
>> +#define MUX_EPLL_SEL_MASK      (1 << 12)
>> +#define MUX_VPLL_SEL_MASK      (1 << 16)
>> +#define MUX_GPLL_SEL_MASK      (1 << 28)
>> +#define MUX_BPLL_SEL_MASK      (1 << 0)
>> +#define MUX_HPM_SEL_MASK       (1 << 20)
>> +#define HPM_SEL_SCLK_MPLL      (1 << 21)
>> +#define APLL_CON0_LOCKED       (1 << 29)
>> +#define MPLL_CON0_LOCKED       (1 << 29)
>> +#define BPLL_CON0_LOCKED       (1 << 29)
>> +#define CPLL_CON0_LOCKED       (1 << 29)
>> +#define EPLL_CON0_LOCKED       (1 << 29)
>> +#define GPLL_CON0_LOCKED       (1 << 29)
>> +#define VPLL_CON0_LOCKED       (1 << 29)
>> +#define CLK_REG_DISABLE                0x0
>> +#define TOP2_VAL               0x0110000
>> +
>> +/* CLK_SRC_PERIC0 */
>> +#define PWM_SEL                0
>> +#define UART3_SEL      6
>> +#define UART2_SEL      6
>> +#define UART1_SEL      6
>> +#define UART0_SEL      6
>> +/* SRC_CLOCK = SCLK_MPLL */
>> +#define CLK_SRC_PERIC0_VAL     ((PWM_SEL << 24)        \
>> +                               | (UART3_SEL << 12)     \
>> +                               | (UART2_SEL << 8)       \
>> +                               | (UART1_SEL << 4)      \
>> +                               | (UART0_SEL))
>> +
>> +/* CLK_SRC_PERIC1 */
>> +/* SRC_CLOCK = SCLK_MPLL */
>> +#define SPI0_SEL               6
>> +#define SPI1_SEL               6
>> +#define SPI2_SEL               6
>> +#define CLK_SRC_PERIC1_VAL     ((SPI2_SEL << 24) \
>> +                               | (SPI1_SEL << 20) \
>> +                               | (SPI0_SEL << 16))
>> +
>> +/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
>> +#define SPI0_ISP_SEL           6
>> +#define SPI1_ISP_SEL           6
>> +#define SCLK_SRC_ISP_VAL       (SPI1_ISP_SEL << 4) \
>> +                               | (SPI0_ISP_SEL << 0)
>> +
>> +/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
>> +#define SPI0_ISP_RATIO         0xf
>> +#define SPI1_ISP_RATIO         0xf
>> +#define SCLK_DIV_ISP_VAL       (SPI1_ISP_RATIO << 12) \
>> +                               | (SPI0_ISP_RATIO << 0)
>> +
>> +/* CLK_DIV_PERIL0      */
>> +#define UART5_RATIO    7
>> +#define UART4_RATIO    7
>> +#define UART3_RATIO    7
>> +#define UART2_RATIO    7
>> +#define UART1_RATIO    7
>> +#define UART0_RATIO    7
>> +
>> +#define CLK_DIV_PERIC0_VAL     ((UART3_RATIO << 12)    \
>> +                               | (UART2_RATIO << 8)    \
>> +                               | (UART1_RATIO << 4)    \
>> +                               | (UART0_RATIO))
>> +/* CLK_DIV_PERIC1 */
>> +#define SPI1_RATIO             0x7
>> +#define SPI0_RATIO             0xf
>> +#define SPI1_SUB_RATIO         0x0
>> +#define SPI0_SUB_RATIO         0x0
>> +#define CLK_DIV_PERIC1_VAL     ((SPI1_SUB_RATIO << 24) \
>> +                               | ((SPI1_RATIO << 16) \
>> +                               | (SPI0_SUB_RATIO << 8) \
>> +                               | (SPI0_RATIO << 0)))
>> +
>> +/* CLK_DIV_PERIC2 */
>> +#define SPI2_RATIO             0xf
>> +#define SPI2_SUB_RATIO         0x0
>> +#define CLK_DIV_PERIC2_VAL     ((SPI2_SUB_RATIO << 8) \
>> +                               | (SPI2_RATIO << 0))
>> +
>> +/* CLK_DIV_PERIC3 */
>> +#define PWM_RATIO              8
>> +#define CLK_DIV_PERIC3_VAL     (PWM_RATIO << 0)
>> +
>> +/* CLK_DIV_FSYS2 */
>> +#define MMC2_RATIO_MASK                0xf
>> +#define MMC2_RATIO_VAL         0x3
>> +#define MMC2_RATIO_OFFSET      0
>> +
>> +#define MMC2_PRE_RATIO_MASK    0xff
>> +#define MMC2_PRE_RATIO_VAL     0x9
>> +#define MMC2_PRE_RATIO_OFFSET  8
>> +
>> +#define MMC3_RATIO_MASK                0xf
>> +#define MMC3_RATIO_VAL         0x1
>> +#define MMC3_RATIO_OFFSET      16
>> +
>> +#define MMC3_PRE_RATIO_MASK    0xff
>> +#define MMC3_PRE_RATIO_VAL     0x0
>> +#define MMC3_PRE_RATIO_OFFSET  24
>> +
>> +/* CLK_SRC_LEX */
>> +#define CLK_SRC_LEX_VAL         0x0
>> +
>> +/* CLK_DIV_LEX */
>> +#define CLK_DIV_LEX_VAL         0x10
>> +
>> +/* CLK_DIV_R0X */
>> +#define CLK_DIV_R0X_VAL         0x10
>> +
>> +/* CLK_DIV_L0X */
>> +#define CLK_DIV_R1X_VAL         0x10
>> +
>> +/* CLK_DIV_ISP0 */
>> +#define CLK_DIV_ISP0_VAL        0x31
>> +
>> +/* CLK_DIV_ISP1 */
>> +#define CLK_DIV_ISP1_VAL        0x0
>> +
>> +/* CLK_DIV_ISP2 */
>> +#define CLK_DIV_ISP2_VAL        0x1
>> +
>> +/* CLK_SRC_DISP1_0 */
>> +#define CLK_SRC_DISP1_0_VAL    0x6
>> +
>> +/*
>> + * DIV_DISP1_0
>> + * For DP, divisor should be 2
>> + */
>> +#define CLK_DIV_DISP1_0_FIMD1  (2 << 0)
>> +
>> +/* CLK_GATE_IP_DISP1 */
>> +#define CLK_GATE_DP1_ALLOW     (1 << 4)
>> +
>> +#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
>> +#define DDR3PHY_CTRL_PHY_RESET_OFF     (0 << 0)
>> +
>> +#define PHY_CON0_RESET_VAL     0x17020a40
>> +#define P0_CMD_EN              (1 << 14)
>> +#define BYTE_RDLVL_EN          (1 << 13)
>> +#define CTRL_SHGATE            (1 << 8)
>> +
>> +#define PHY_CON1_RESET_VAL     0x09210100
>> +#define CTRL_GATEDURADJ_MASK   (0xf << 20)
>> +
>> +#define PHY_CON2_RESET_VAL     0x00010004
>> +#define INIT_DESKEW_EN         (1 << 6)
>> +#define RDLVL_GATE_EN          (1 << 24)
>> +
>> +/*ZQ Configurations */
>> +#define PHY_CON16_RESET_VAL    0x08000304
>> +
>> +#define ZQ_CLK_DIV_EN          (1 << 18)
>> +#define ZQ_MANUAL_STR          (1 << 1)
>> +#define ZQ_DONE                        (1 << 0)
>> +
>> +#define CTRL_RDLVL_GATE_ENABLE 1
>> +#define CTRL_RDLVL_GATE_DISABLE        1
>> +
>> +/* Direct Command */
>> +#define DIRECT_CMD_NOP                 0x07000000
>> +#define DIRECT_CMD_PALL                        0x01000000
>> +#define DIRECT_CMD_ZQINIT              0x0a000000
>> +#define DIRECT_CMD_CHANNEL_SHIFT       28
>> +#define DIRECT_CMD_CHIP_SHIFT          20
>> +
>> +/* DMC PHY Control0 register */
>> +#define PHY_CONTROL0_RESET_VAL 0x0
>> +#define MEM_TERM_EN    (1 << 31)       /* Termination enable for memory */
>> +#define PHY_TERM_EN    (1 << 30)       /* Termination enable for PHY */
>> +#define DMC_CTRL_SHGATE        (1 << 29)       /* Duration of DQS gating signal */
>> +#define FP_RSYNC       (1 << 3)        /* Force DLL resyncronization */
>> +
>> +/* Driver strength for CK, CKE, CS & CA */
>> +#define IMP_OUTPUT_DRV_40_OHM  0x5
>> +#define IMP_OUTPUT_DRV_30_OHM  0x7
>> +#define CA_CK_DRVR_DS_OFFSET   9
>> +#define CA_CKE_DRVR_DS_OFFSET  6
>> +#define CA_CS_DRVR_DS_OFFSET   3
>> +#define CA_ADR_DRVR_DS_OFFSET  0
>> +
>> +#define PHY_CON42_CTRL_BSTLEN_SHIFT    8
>> +#define PHY_CON42_CTRL_RDLAT_SHIFT     0
>> +
>> +struct mem_timings;
>> +
>> +/* Errors that we can encourter in low-level setup */
>> +enum {
>> +       SETUP_ERR_OK,
>> +       SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
>> +       SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
>> +};
>> +
>> +/*
>> + * Memory variant specific initialization code
>> + *
>> + * @param mem          Memory timings for this memory type.
>> + * @param mem_iv_size  Memory interleaving size is a configurable parameter
>> + *                     which the DMC uses to decide how to split a memory
>> + *                     chunk into smaller chunks to support concurrent
>> + *                     accesses; may vary across boards.
>> + * @return 0 if ok, SETUP_ERR_... if there is a problem
>> + */
>> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
>> +
>> +/*
>> + * Configure ZQ I/O interface
>> + *
>> + * @param mem          Memory timings for this memory type.
>> + * @param phy0_ctrl    Pointer to struct containing PHY0 control reg
>> + * @param phy1_ctrl    Pointer to struct containing PHY1 control reg
>> + * @return 0 if ok, -1 on error
>> + */
>> +int dmc_config_zq(struct mem_timings *mem,
>> +                 struct exynos5_phy_control *phy0_ctrl,
>> +                 struct exynos5_phy_control *phy1_ctrl);
>> +
>> +/*
>> + * Send NOP and MRS/EMRS Direct commands
>> + *
>> + * @param mem          Memory timings for this memory type.
>> + * @param dmc          Pointer to struct of DMC registers
>> + */
>> +void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
>> +
>> +/*
>> + * Send PALL Direct commands
>> + *
>> + * @param mem          Memory timings for this memory type.
>> + * @param dmc          Pointer to struct of DMC registers
>> + */
>> +void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
>> +
>> +/*
>> + * Configure the memconfig and membaseconfig registers
>> + *
>> + * @param mem          Memory timings for this memory type.
>> + * @param exynos5_dmc  Pointer to struct of DMC registers
>> + */
>> +void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
>> +
>> +/*
>> + * Reset the DLL. This function is common between DDR3 and LPDDR2.
>> + * However, the reset value is different. So we are passing a flag
>> + * ddr_mode to distinguish between LPDDR2 and DDR3.
>> + *
>> + * @param exynos5_dmc  Pointer to struct of DMC registers
>> + * @param ddr_mode     Type of DDR memory
>> + */
>> +void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
>> +
>> +void sdelay(unsigned long);
>> +void mem_ctrl_init(void);
>> +void system_clock_init(void);
>> +#endif
>> diff --git a/board/samsung/dts/exynos5250-arndale.dts b/board/samsung/dts/exynos5250-arndale.dts
>> new file mode 100644
>> index 0000000..9b4d6b2
>> --- /dev/null
>> +++ b/board/samsung/dts/exynos5250-arndale.dts
>> @@ -0,0 +1,36 @@
>> +/*
>> + * SAMSUNG Arndale board device tree source
>> + *
>> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
>> + *             http://www.samsung.com
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> +*/
>> +
>> +/dts-v1/;
>> +/include/ ARCH_CPU_DTS
>> +
>> +/ {
>> +       model = "SAMSUNG Arndale board based on EXYNOS5250";
>> +       compatible = "samsung,arndale", "samsung,exynos5250";
>> +
>> +       mmc@12200000 {
>> +               samsung,bus-width = <8>;
>> +               samsung,timing = <1 3 3>;
>> +       };
>> +
>> +       mmc@12210000 {
>> +               status = "disabled";
>> +       };
>> +
>> +       mmc@12220000 {
>> +               samsung,bus-width = <4>;
>> +               samsung,timing = <1 2 3>;
>> +       };
>> +
>> +       mmc@12230000 {
>> +               status = "disabled";
>> +       };
>> +};
>> diff --git a/boards.cfg b/boards.cfg
>> index 54357eb..572b242 100644
>> --- a/boards.cfg
>> +++ b/boards.cfg
>> @@ -288,6 +288,7 @@ origen                           arm         armv7       origen              samsung        exynos
>>  s5pc210_universal            arm         armv7       universal_c210      samsung        exynos
>>  snow                        arm         armv7       smdk5250            samsung        exynos
>>  smdk5250                    arm         armv7       smdk5250            samsung        exynos
>> +arndale                             arm         armv7       arndale             samsung        exynos
>>  smdkv310                    arm         armv7       smdkv310            samsung        exynos
>>  trats                        arm         armv7       trats               samsung        exynos
>>  harmony                      arm         armv7:arm720t harmony           nvidia         tegra20
>> diff --git a/include/configs/arndale.h b/include/configs/arndale.h
>> new file mode 100644
>> index 0000000..caa83b8
>> --- /dev/null
>> +++ b/include/configs/arndale.h
>> @@ -0,0 +1,39 @@
>> +/*
>> + * Copyright (C) 2013 Samsung Electronics
>> + *
>> + * Configuration settings for the SAMSUNG Arndale board.
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>> + * MA 02111-1307 USA
>> + */
>> +
>> +#ifndef __CONFIG_ARNDALE_H
>> +#define __CONFIG_ARNDALE_H
>> +
>> +#undef CONFIG_DEFAULT_DEVICE_TREE
>> +#define CONFIG_DEFAULT_DEVICE_TREE     exynos5250-arndale
>> +
>> +#define CONFIG_ARNDALE
>> +
>> +#define CONFIG_ENV_IS_IN_MMC
>> +#define CONFIG_SERIAL2
>> +#define CONFIG_IDENT_STRING            " for Arndale"
>> +
>> +#include <configs/exynos5250-dt.h>
>> +
>> +#endif /* __CONFIG_ARNDALE_H */
>> diff --git a/tools/Makefile b/tools/Makefile
>> index c5952fc..ab7d339 100644
>> --- a/tools/Makefile
>> +++ b/tools/Makefile
>> @@ -69,6 +69,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
>>  BIN_FILES-y += mkenvimage$(SFX)
>>  BIN_FILES-y += mkimage$(SFX)
>>  BIN_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl$(SFX)
>> +BIN_FILES-$(CONFIG_ARNDALE) += mkarndalespl$(SFX)
>>  BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
>>  BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
>>  BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
>> @@ -99,6 +100,7 @@ NOPED_OBJ_FILES-y += omapimage.o
>>  NOPED_OBJ_FILES-y += mkenvimage.o
>>  NOPED_OBJ_FILES-y += mkimage.o
>>  OBJ_FILES-$(CONFIG_SMDK5250) += mkexynosspl.o
>> +OBJ_FILES-$(CONFIG_ARNDALE) += mkexynosspl.o
>>  OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
>>  OBJ_FILES-$(CONFIG_MX28) += mxsboot.o
>>  OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o
>> --
>> 1.7.9.5
>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot@lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot
>
>
>
> --
> Regards,
> Rajeshwari Shinde
diff mbox

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index f6723ef..b112581 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -736,6 +736,10 @@  Chander Kashyap <k.chander@samsung.com>
 	SMDKV310		ARM ARMV7 (EXYNOS4210 SoC)
 	SMDK5250		ARM ARMV7 (EXYNOS5250 SoC)
 
+Inderpal Singh <inderpal.singh@linaro.org>
+
+	Arndale			ARM ARMV7 (EXYNOS5250 SoC)
+
 Lukasz Majewski <l.majewski@samsung.com>
 
 	trats			ARM ARMV7 (EXYNOS4210 SoC)
diff --git a/board/samsung/arndale/Makefile b/board/samsung/arndale/Makefile
new file mode 100644
index 0000000..f65d111
--- /dev/null
+++ b/board/samsung/arndale/Makefile
@@ -0,0 +1,54 @@ 
+#
+# Copyright (C) 2013 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+SOBJS	:= lowlevel_init.o
+
+COBJS	:= clock_init.o
+COBJS	+= dmc_common.o dmc_init_ddr3.o
+COBJS	+= arndale_spl.o
+
+ifndef CONFIG_SPL_BUILD
+COBJS	+= arndale.o
+endif
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL	:=	 $(obj).depend $(LIB)
+
+all:	$(ALL)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
new file mode 100644
index 0000000..7f8a568
--- /dev/null
+++ b/board/samsung/arndale/arndale.c
@@ -0,0 +1,117 @@ 
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/power.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+	return 0;
+}
+
+int dram_init(void)
+{
+	int i;
+	u32 addr;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+	}
+	return 0;
+}
+
+int power_init_board(void)
+{
+	set_ps_hold_ctrl();
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	int i;
+	u32 addr, size;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+		size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+		gd->bd->bi_dram[i].start = addr;
+		gd->bd->bi_dram[i].size = size;
+	}
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+	/* dwmmc initializattion for available channels */
+	ret = exynos_dwmmc_init(gd->fdt_blob);
+	if (ret)
+		debug("dwmmc init failed\n");
+
+	return ret;
+}
+#endif
+
+static int board_uart_init(void)
+{
+	int err, uart_id, ret = 0;
+
+	for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+		err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+		if (err) {
+			debug("UART%d not configured\n",
+					 (uart_id - PERIPH_ID_UART0));
+			ret |= err;
+		}
+	}
+	return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+	int err;
+	err = board_uart_init();
+	if (err) {
+		debug("UART init failed\n");
+		return err;
+	}
+	return err;
+}
+#endif
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	printf("\nBoard: Arndale\n");
+
+	return 0;
+}
+#endif
+
diff --git a/board/samsung/arndale/arndale_spl.c b/board/samsung/arndale/arndale_spl.c
new file mode 100644
index 0000000..8135708
--- /dev/null
+++ b/board/samsung/arndale/arndale_spl.c
@@ -0,0 +1,66 @@ 
+/*
+ * Copyright (c) 2012 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#define SIGNATURE	0xdeadbeef
+
+/* Parameters of early board initialization in SPL */
+static struct spl_machine_param machine_param
+		__attribute__((section(".machine_param"))) = {
+	.signature	= SIGNATURE,
+	.version	= 1,
+	.params		= "vmubfasirM",
+	.size		= sizeof(machine_param),
+
+	.mem_iv_size	= 0x1f,
+	.mem_type	= DDR_MODE_DDR3,
+
+	/*
+	 * Set uboot_size to 0x100000 bytes.
+	 *
+	 * This is an overly conservative value chosen to accommodate all
+	 * possible U-Boot image.  You are advised to set this value to a
+	 * smaller realistic size via scripts that modifies the .machine_param
+	 * section of output U-Boot image.
+	 */
+	.uboot_size	= 0x100000,
+
+	.boot_source	= BOOT_MODE_OM,
+	.frequency_mhz	= 800,
+	.arm_freq_mhz	= 1000,
+	.serial_base	= 0x12c30000,
+	.i2c_base	= 0x12c60000,
+	.mem_manuf	= MEM_MANUF_SAMSUNG,
+};
+
+struct spl_machine_param *spl_get_machine_params(void)
+{
+	if (machine_param.signature != SIGNATURE) {
+		/* Will hang if SIGNATURE dont match */
+		while (1)
+			;
+	}
+
+	return &machine_param;
+}
diff --git a/board/samsung/arndale/clock_init.c b/board/samsung/arndale/clock_init.c
new file mode 100644
index 0000000..a9b0bbd
--- /dev/null
+++ b/board/samsung/arndale/clock_init.c
@@ -0,0 +1,655 @@ 
+/*
+ * Clock setup for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "setup.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct arm_clk_ratios arm_clk_ratios[] = {
+	{
+		.arm_freq_mhz = 600,
+
+		.apll_mdiv = 0xc8,
+		.apll_pdiv = 0x4,
+		.apll_sdiv = 0x1,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x2,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x1,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 800,
+
+		.apll_mdiv = 0x64,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x3,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1000,
+
+		.apll_mdiv = 0x7d,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x4,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1200,
+
+		.apll_mdiv = 0x96,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x5,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1400,
+
+		.apll_mdiv = 0xaf,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1700,
+
+		.apll_mdiv = 0x1a9,
+		.apll_pdiv = 0x6,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}
+};
+struct mem_timings mem_timings[] = {
+	{
+		.mem_manuf = MEM_MANUF_ELPIDA,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x0,
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x2,
+		.gpll_mdiv = 0x215,
+		.gpll_pdiv = 0xc,
+		.gpll_sdiv = 0x1,
+		.epll_mdiv = 0x60,
+		.epll_pdiv = 0x3,
+		.epll_sdiv = 0x3,
+		.vpll_mdiv = 0x96,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+
+		.bpll_mdiv = 0x64,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x0,
+		.pclk_cdrex_ratio = 0x5,
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010042, 0x00000d70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x8c36650e,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a44,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x4,
+		.phy1_tFS = 0x4,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x7,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 0,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_ENABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+			DMC_MEMCONFIGx_CHIP_COL_10 |
+			DMC_MEMCONFIGx_CHIP_ROW_15 |
+			DMC_MEMCONFIGx_CHIP_BANK_8,
+		.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+		.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 2,
+		.chips_per_channel = 2,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.impedance = IMP_OUTPUT_DRV_30_OHM,
+		.gate_leveling_enable = 0,
+	}, {
+		.mem_manuf = MEM_MANUF_SAMSUNG,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x0,
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x2,
+		.gpll_mdiv = 0x215,
+		.gpll_pdiv = 0xc,
+		.gpll_sdiv = 0x1,
+		.epll_mdiv = 0x60,
+		.epll_pdiv = 0x3,
+		.epll_sdiv = 0x3,
+		.vpll_mdiv = 0x96,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+
+		.bpll_mdiv = 0x64,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x0,
+		.pclk_cdrex_ratio = 0x5,
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010000, 0x00000d70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x8c36650e,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a44,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x8,
+		.phy1_tFS = 0x8,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x5,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 1,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_ENABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+			DMC_MEMCONFIGx_CHIP_COL_10 |
+			DMC_MEMCONFIGx_CHIP_ROW_15 |
+			DMC_MEMCONFIGx_CHIP_BANK_8,
+		.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+		.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 2,
+		.chips_per_channel = 2,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.impedance = IMP_OUTPUT_DRV_40_OHM,
+		.gate_leveling_enable = 1,
+	}
+};
+
+/**
+ * Get the required memory type and speed (SPL version).
+ *
+ * In SPL we have no device tree, so we use the machine parameters
+ *
+ * @param mem_type	Returns memory type
+ * @param frequency_mhz	Returns memory speed in MHz
+ * @param arm_freq	Returns ARM clock speed in MHz
+ * @param mem_manuf	Return Memory Manufacturer name
+ * @return 0 if all ok
+ */
+static int clock_get_mem_selection(enum ddr_mode *mem_type,
+		unsigned *frequency_mhz, unsigned *arm_freq,
+		enum mem_manuf *mem_manuf)
+{
+	struct spl_machine_param *params;
+
+	params = spl_get_machine_params();
+	*mem_type = params->mem_type;
+	*frequency_mhz = params->frequency_mhz;
+	*arm_freq = params->arm_freq_mhz;
+	*mem_manuf = params->mem_manuf;
+
+	return 0;
+}
+
+/* Get the ratios for setting ARM clock */
+struct arm_clk_ratios *get_arm_ratios(void)
+{
+	struct arm_clk_ratios *arm_ratio;
+	enum ddr_mode mem_type;
+	enum mem_manuf mem_manuf;
+	unsigned frequency_mhz, arm_freq;
+	int i;
+
+	if (clock_get_mem_selection(&mem_type, &frequency_mhz,
+					&arm_freq, &mem_manuf))
+		;
+	for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
+		i++, arm_ratio++) {
+		if (arm_ratio->arm_freq_mhz == arm_freq)
+			return arm_ratio;
+	}
+
+	/* will hang if failed to find clock ratio */
+	while (1)
+		;
+
+	return NULL;
+}
+
+struct mem_timings *clock_get_mem_timings(void)
+{
+	struct mem_timings *mem;
+	enum ddr_mode mem_type;
+	enum mem_manuf mem_manuf;
+	unsigned frequency_mhz, arm_freq;
+	int i;
+
+	if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
+						&arm_freq, &mem_manuf)) {
+		for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
+				i++, mem++) {
+			if (mem->mem_type == mem_type &&
+					mem->frequency_mhz == frequency_mhz &&
+					mem->mem_manuf == mem_manuf)
+				return mem;
+		}
+	}
+
+	/* will hang if failed to find memory timings */
+	while (1)
+		;
+
+	return NULL;
+}
+
+void system_clock_init()
+{
+	struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+	struct mem_timings *mem;
+	struct arm_clk_ratios *arm_clk_ratio;
+	u32 val, tmp;
+
+	mem = clock_get_mem_timings();
+	arm_clk_ratio = get_arm_ratios();
+
+	clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_cpu);
+	} while ((val | MUX_APLL_SEL_MASK) != val);
+
+	clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_core1);
+	} while ((val | MUX_MPLL_SEL_MASK) != val);
+
+	clrbits_le32(&clk->src_core1, MUX_CPLL_SEL_MASK);
+	clrbits_le32(&clk->src_core1, MUX_EPLL_SEL_MASK);
+	clrbits_le32(&clk->src_core1, MUX_VPLL_SEL_MASK);
+	clrbits_le32(&clk->src_core1, MUX_GPLL_SEL_MASK);
+	tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
+		| MUX_GPLL_SEL_MASK;
+	do {
+		val = readl(&clk->mux_stat_top2);
+	} while ((val | tmp) != val);
+
+	clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_cdrex);
+	} while ((val | MUX_BPLL_SEL_MASK) != val);
+
+	/* PLL locktime */
+	writel(APLL_LOCK_VAL, &clk->apll_lock);
+
+	writel(MPLL_LOCK_VAL, &clk->mpll_lock);
+
+	writel(BPLL_LOCK_VAL, &clk->bpll_lock);
+
+	writel(CPLL_LOCK_VAL, &clk->cpll_lock);
+
+	writel(GPLL_LOCK_VAL, &clk->gpll_lock);
+
+	writel(EPLL_LOCK_VAL, &clk->epll_lock);
+
+	writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+
+	writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
+
+	writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
+	do {
+		val = readl(&clk->mux_stat_cpu);
+	} while ((val | HPM_SEL_SCLK_MPLL) != val);
+
+	val = arm_clk_ratio->arm2_ratio << 28
+		| arm_clk_ratio->apll_ratio << 24
+		| arm_clk_ratio->pclk_dbg_ratio << 20
+		| arm_clk_ratio->atb_ratio << 16
+		| arm_clk_ratio->periph_ratio << 12
+		| arm_clk_ratio->acp_ratio << 8
+		| arm_clk_ratio->cpud_ratio << 4
+		| arm_clk_ratio->arm_ratio;
+	writel(val, &clk->div_cpu0);
+	do {
+		val = readl(&clk->div_stat_cpu0);
+	} while (0 != val);
+
+	writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+	do {
+		val = readl(&clk->div_stat_cpu1);
+	} while (0 != val);
+
+	/* Set APLL */
+	writel(APLL_CON1_VAL, &clk->apll_con1);
+	val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
+			arm_clk_ratio->apll_sdiv);
+	writel(val, &clk->apll_con0);
+	while (readl(&clk->apll_con0) & APLL_CON0_LOCKED)
+		;
+
+	/* Set MPLL */
+	writel(MPLL_CON1_VAL, &clk->mpll_con1);
+	val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+	writel(val, &clk->mpll_con0);
+	while (readl(&clk->mpll_con0) & MPLL_CON0_LOCKED)
+		;
+
+	/* Set BPLL */
+	writel(BPLL_CON1_VAL, &clk->bpll_con1);
+	val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+	writel(val, &clk->bpll_con0);
+	while (readl(&clk->bpll_con0) & BPLL_CON0_LOCKED)
+		;
+
+	/* Set CPLL */
+	writel(CPLL_CON1_VAL, &clk->cpll_con1);
+	val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+	writel(val, &clk->cpll_con0);
+	while (readl(&clk->cpll_con0) & CPLL_CON0_LOCKED)
+		;
+
+	/* Set GPLL */
+	writel(GPLL_CON1_VAL, &clk->gpll_con1);
+	val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
+	writel(val, &clk->gpll_con0);
+	while (readl(&clk->gpll_con0) & GPLL_CON0_LOCKED)
+		;
+
+	/* Set EPLL */
+	writel(EPLL_CON2_VAL, &clk->epll_con2);
+	writel(EPLL_CON1_VAL, &clk->epll_con1);
+	val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+	writel(val, &clk->epll_con0);
+	while (readl(&clk->epll_con0) & EPLL_CON0_LOCKED)
+		;
+
+	/* Set VPLL */
+	writel(VPLL_CON2_VAL, &clk->vpll_con2);
+	writel(VPLL_CON1_VAL, &clk->vpll_con1);
+	val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+	writel(val, &clk->vpll_con0);
+	while (readl(&clk->vpll_con0) & VPLL_CON0_LOCKED)
+		;
+
+	writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
+	writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
+	while (readl(&clk->div_stat_core0) != 0)
+		;
+
+	writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
+	while (readl(&clk->div_stat_core1) != 0)
+		;
+
+	writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
+	while (readl(&clk->div_stat_sysrgt) != 0)
+		;
+
+	writel(CLK_DIV_ACP_VAL, &clk->div_acp);
+	while (readl(&clk->div_stat_acp) != 0)
+		;
+
+	writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
+	while (readl(&clk->div_stat_syslft) != 0)
+		;
+
+	writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+	writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+	writel(TOP2_VAL, &clk->src_top2);
+	writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+
+	writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+	while (readl(&clk->div_stat_top0))
+		;
+
+	writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+	while (readl(&clk->div_stat_top1))
+		;
+
+	writel(CLK_SRC_LEX_VAL, &clk->src_lex);
+	while (1) {
+		val = readl(&clk->mux_stat_lex);
+		if (val == (val | 1))
+			break;
+	}
+
+	writel(CLK_DIV_LEX_VAL, &clk->div_lex);
+	while (readl(&clk->div_stat_lex))
+		;
+
+	writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+	while (readl(&clk->div_stat_r0x))
+		;
+
+	writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+	while (readl(&clk->div_stat_r0x))
+		;
+
+	writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
+	while (readl(&clk->div_stat_r1x))
+		;
+
+	writel(CLK_REG_DISABLE, &clk->src_cdrex);
+
+	writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
+	while (readl(&clk->div_stat_cdrex))
+		;
+
+	val = readl(&clk->src_cpu);
+	val |= CLK_SRC_CPU_VAL;
+	writel(val, &clk->src_cpu);
+
+	val = readl(&clk->src_top2);
+	val |= CLK_SRC_TOP2_VAL;
+	writel(val, &clk->src_top2);
+
+	val = readl(&clk->src_core1);
+	val |= CLK_SRC_CORE1_VAL;
+	writel(val, &clk->src_core1);
+
+	writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+	writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+	while (readl(&clk->div_stat_fsys0))
+		;
+
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
+
+	writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+	writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+
+	writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+	writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+	writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+	writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+
+	writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
+	writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
+	writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+	writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+	writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
+
+	/* FIMD1 SRC CLK SELECTION */
+	writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
+
+	val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
+		| MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
+		| MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
+		| MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
+	writel(val, &clk->div_fsys2);
+}
diff --git a/board/samsung/arndale/clock_init.h b/board/samsung/arndale/clock_init.h
new file mode 100644
index 0000000..5d01a6c
--- /dev/null
+++ b/board/samsung/arndale/clock_init.h
@@ -0,0 +1,149 @@ 
+/*
+ * Clock initialization routines
+ *
+ * Copyright (c) 2011 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ARNDALE_CLOCK_INIT_H
+#define __ARNDALE_CLOCK_INIT_H
+
+enum {
+	MEM_TIMINGS_MSR_COUNT	= 4,
+};
+
+/* These are the ratio's for configuring ARM clock */
+struct arm_clk_ratios {
+	unsigned arm_freq_mhz;		/* Frequency of ARM core in MHz */
+
+	unsigned apll_mdiv;
+	unsigned apll_pdiv;
+	unsigned apll_sdiv;
+
+	unsigned arm2_ratio;
+	unsigned apll_ratio;
+	unsigned pclk_dbg_ratio;
+	unsigned atb_ratio;
+	unsigned periph_ratio;
+	unsigned acp_ratio;
+	unsigned cpud_ratio;
+	unsigned arm_ratio;
+};
+
+/* These are the memory timings for a particular memory type and speed */
+struct mem_timings {
+	enum mem_manuf mem_manuf;	/* Memory manufacturer */
+	enum ddr_mode mem_type;		/* Memory type */
+	unsigned frequency_mhz;		/* Frequency of memory in MHz */
+
+	/* Here follow the timing parameters for the selected memory */
+	unsigned apll_mdiv;
+	unsigned apll_pdiv;
+	unsigned apll_sdiv;
+	unsigned mpll_mdiv;
+	unsigned mpll_pdiv;
+	unsigned mpll_sdiv;
+	unsigned cpll_mdiv;
+	unsigned cpll_pdiv;
+	unsigned cpll_sdiv;
+	unsigned gpll_mdiv;
+	unsigned gpll_pdiv;
+	unsigned gpll_sdiv;
+	unsigned epll_mdiv;
+	unsigned epll_pdiv;
+	unsigned epll_sdiv;
+	unsigned vpll_mdiv;
+	unsigned vpll_pdiv;
+	unsigned vpll_sdiv;
+	unsigned bpll_mdiv;
+	unsigned bpll_pdiv;
+	unsigned bpll_sdiv;
+	unsigned pclk_cdrex_ratio;
+	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+
+	unsigned timing_ref;
+	unsigned timing_row;
+	unsigned timing_data;
+	unsigned timing_power;
+
+	/* DQS, DQ, DEBUG offsets */
+	unsigned phy0_dqs;
+	unsigned phy1_dqs;
+	unsigned phy0_dq;
+	unsigned phy1_dq;
+	unsigned phy0_tFS;
+	unsigned phy1_tFS;
+	unsigned phy0_pulld_dqs;
+	unsigned phy1_pulld_dqs;
+
+	unsigned lpddr3_ctrl_phy_reset;
+	unsigned ctrl_start_point;
+	unsigned ctrl_inc;
+	unsigned ctrl_start;
+	unsigned ctrl_dll_on;
+	unsigned ctrl_ref;
+
+	unsigned ctrl_force;
+	unsigned ctrl_rdlat;
+	unsigned ctrl_bstlen;
+
+	unsigned fp_resync;
+	unsigned iv_size;
+	unsigned dfi_init_start;
+	unsigned aref_en;
+
+	unsigned rd_fetch;
+
+	unsigned zq_mode_dds;
+	unsigned zq_mode_term;
+	unsigned zq_mode_noterm;	/* 1 to allow termination disable */
+
+	unsigned memcontrol;
+	unsigned memconfig;
+
+	unsigned membaseconfig0;
+	unsigned membaseconfig1;
+	unsigned prechconfig_tp_cnt;
+	unsigned dpwrdn_cyc;
+	unsigned dsref_cyc;
+	unsigned concontrol;
+	/* Channel and Chip Selection */
+	uint8_t dmc_channels;		/* number of memory channels */
+	uint8_t chips_per_channel;	/* number of chips per channel */
+	uint8_t chips_to_configure;	/* number of chips to configure */
+	uint8_t send_zq_init;		/* 1 to send this command */
+	unsigned impedance;		/* drive strength impedeance */
+	uint8_t gate_leveling_enable;	/* check gate leveling is enabled */
+};
+
+/**
+ * Get the correct memory timings for our selected memory type and speed.
+ *
+ * This function can be called from SPL or the main U-Boot.
+ *
+ * @return pointer to the memory timings that we should use
+ */
+struct mem_timings *clock_get_mem_timings(void);
+
+/*
+ * Initialize clock for the device
+ */
+void system_clock_init(void);
+#endif
diff --git a/board/samsung/arndale/dmc_common.c b/board/samsung/arndale/dmc_common.c
new file mode 100644
index 0000000..5a51def
--- /dev/null
+++ b/board/samsung/arndale/dmc_common.c
@@ -0,0 +1,199 @@ 
+/*
+ * Mem setup common file for different types of DDR present on Arndale boards.
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "setup.h"
+
+#define ZQ_INIT_TIMEOUT	10000
+
+int dmc_config_zq(struct mem_timings *mem,
+		  struct exynos5_phy_control *phy0_ctrl,
+		  struct exynos5_phy_control *phy1_ctrl)
+{
+	unsigned long val = 0;
+	int i;
+
+	/*
+	 * ZQ Calibration:
+	 * Select Driver Strength,
+	 * long calibration for manual calibration
+	 */
+	val = PHY_CON16_RESET_VAL;
+	val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
+	val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
+	val |= ZQ_CLK_DIV_EN;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* Disable termination */
+	if (mem->zq_mode_noterm)
+		val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* ZQ_MANUAL_START: Enable */
+	val |= ZQ_MANUAL_STR;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* ZQ_MANUAL_START: Disable */
+	val &= ~ZQ_MANUAL_STR;
+
+	/*
+	 * Since we are manaully calibrating the ZQ values,
+	 * we are looping for the ZQ_init to complete.
+	 */
+	i = ZQ_INIT_TIMEOUT;
+	while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+		sdelay(100);
+		i--;
+	}
+	if (!i)
+		return -1;
+	writel(val, &phy0_ctrl->phy_con16);
+
+	i = ZQ_INIT_TIMEOUT;
+	while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+		sdelay(100);
+		i--;
+	}
+	if (!i)
+		return -1;
+	writel(val, &phy1_ctrl->phy_con16);
+
+	return 0;
+}
+
+void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
+{
+	unsigned long val;
+
+	if (mode == DDR_MODE_DDR3) {
+		val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
+		writel(val, &dmc->phycontrol0);
+	}
+
+	/* Update DLL Information: Force DLL Resyncronization */
+	val = readl(&dmc->phycontrol0);
+	val |= FP_RSYNC;
+	writel(val, &dmc->phycontrol0);
+
+	/* Reset Force DLL Resyncronization */
+	val = readl(&dmc->phycontrol0);
+	val &= ~FP_RSYNC;
+	writel(val, &dmc->phycontrol0);
+}
+
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	int channel, chip;
+
+	for (channel = 0; channel < mem->dmc_channels; channel++) {
+		unsigned long mask;
+
+		mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+		for (chip = 0; chip < mem->chips_to_configure; chip++) {
+			int i;
+
+			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+			/* Sending NOP command */
+			writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
+
+			/*
+			 * TODO(alim.akhtar@samsung.com): Do we need these
+			 * delays? This one and the next were not there for
+			 * DDR3.
+			 */
+			sdelay(0x10000);
+
+			/* Sending EMRS/MRS commands */
+			for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+				writel(mem->direct_cmd_msr[i] | mask,
+				       &dmc->directcmd);
+				sdelay(0x10000);
+			}
+
+			if (mem->send_zq_init) {
+				/* Sending ZQINIT command */
+				writel(DIRECT_CMD_ZQINIT | mask,
+				       &dmc->directcmd);
+
+				sdelay(10000);
+			}
+		}
+	}
+}
+
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	int channel, chip;
+
+	for (channel = 0; channel < mem->dmc_channels; channel++) {
+		unsigned long mask;
+
+		mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+		for (chip = 0; chip < mem->chips_per_channel; chip++) {
+			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+			/* PALL (all banks precharge) CMD */
+			writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
+			sdelay(0x10000);
+		}
+	}
+}
+
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	writel(mem->memconfig, &dmc->memconfig0);
+	writel(mem->memconfig, &dmc->memconfig1);
+	writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
+	writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
+}
+
+void mem_ctrl_init()
+{
+	struct spl_machine_param *param = spl_get_machine_params();
+	struct mem_timings *mem;
+	int ret;
+
+	mem = clock_get_mem_timings();
+
+	/* If there are any other memory variant, add their init call below */
+	if (param->mem_type == DDR_MODE_DDR3) {
+		ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size);
+		if (ret) {
+			/* will hang if failed to init memory control */
+			while (1)
+				;
+		}
+	} else {
+		/* will hang if unknow memory type  */
+		while (1)
+			;
+	}
+}
diff --git a/board/samsung/arndale/dmc_init_ddr3.c b/board/samsung/arndale/dmc_init_ddr3.c
new file mode 100644
index 0000000..ce91451
--- /dev/null
+++ b/board/samsung/arndale/dmc_init_ddr3.c
@@ -0,0 +1,228 @@ 
+/*
+ * DDR3 mem setup file for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include "setup.h"
+#include "clock_init.h"
+
+#define RDLVL_COMPLETE_TIMEOUT	10000
+
+static void reset_phy_ctrl(void)
+{
+	struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+
+	writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
+	writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
+}
+
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
+{
+	unsigned int val;
+	struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+	struct exynos5_dmc *dmc;
+	int i;
+
+	phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
+	phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
+	dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
+
+	reset_phy_ctrl();
+
+	/* Set Impedance Output Driver */
+	val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_CS_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_ADR_DRVR_DS_OFFSET);
+	writel(val, &phy0_ctrl->phy_con39);
+	writel(val, &phy1_ctrl->phy_con39);
+
+	/* Set Read Latency and Burst Length for PHY0 and PHY1 */
+	val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
+		(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
+	writel(val, &phy0_ctrl->phy_con42);
+	writel(val, &phy1_ctrl->phy_con42);
+
+	/* ZQ Calibration */
+	if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
+		return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
+
+	/* DQ Signal */
+	writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
+	writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
+
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+		| (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
+		&dmc->concontrol);
+
+	update_reset_dll(dmc, DDR_MODE_DDR3);
+
+	/* DQS Signal */
+	writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
+	writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
+
+	writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
+	writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
+
+	writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
+	writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
+
+	val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
+		(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+		(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+		(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+	writel(val, &phy0_ctrl->phy_con12);
+	writel(val, &phy1_ctrl->phy_con12);
+
+	/* Start DLL locking */
+	writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+		&phy0_ctrl->phy_con12);
+	writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+		&phy1_ctrl->phy_con12);
+
+	update_reset_dll(dmc, DDR_MODE_DDR3);
+
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+		&dmc->concontrol);
+
+	/* Memory Channel Inteleaving Size */
+	writel(mem->iv_size, &dmc->ivcontrol);
+
+	writel(mem->memconfig, &dmc->memconfig0);
+	writel(mem->memconfig, &dmc->memconfig1);
+	writel(mem->membaseconfig0, &dmc->membaseconfig0);
+	writel(mem->membaseconfig1, &dmc->membaseconfig1);
+
+	/* Precharge Configuration */
+	writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+		&dmc->prechconfig);
+
+	/* Power Down mode Configuration */
+	writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
+		mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
+		&dmc->pwrdnconfig);
+
+	/* TimingRow, TimingData, TimingPower and Timingaref
+	 * values as per Memory AC parameters
+	 */
+	writel(mem->timing_ref, &dmc->timingref);
+	writel(mem->timing_row, &dmc->timingrow);
+	writel(mem->timing_data, &dmc->timingdata);
+	writel(mem->timing_power, &dmc->timingpower);
+
+	/* Send PALL command */
+	dmc_config_prech(mem, dmc);
+
+	/* Send NOP, MRS and ZQINIT commands */
+	dmc_config_mrs(mem, dmc);
+
+	if (mem->gate_leveling_enable) {
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = PHY_CON2_RESET_VAL;
+		val |= INIT_DESKEW_EN;
+		writel(val, &phy0_ctrl->phy_con2);
+		writel(val, &phy1_ctrl->phy_con2);
+
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		val |= BYTE_RDLVL_EN;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = (mem->ctrl_start_point <<
+				PHY_CON12_CTRL_START_POINT_SHIFT) |
+			(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+			(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+			(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+			(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+		writel(val, &phy0_ctrl->phy_con12);
+		writel(val, &phy1_ctrl->phy_con12);
+
+		val = PHY_CON2_RESET_VAL;
+		val |= INIT_DESKEW_EN;
+		val |= RDLVL_GATE_EN;
+		writel(val, &phy0_ctrl->phy_con2);
+		writel(val, &phy1_ctrl->phy_con2);
+
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		val |= BYTE_RDLVL_EN;
+		val |= CTRL_SHGATE;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = PHY_CON1_RESET_VAL;
+		val &= ~(CTRL_GATEDURADJ_MASK);
+		writel(val, &phy0_ctrl->phy_con1);
+		writel(val, &phy1_ctrl->phy_con1);
+
+		writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
+		i = RDLVL_COMPLETE_TIMEOUT;
+		while ((readl(&dmc->phystatus) &
+			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
+			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
+			/*
+			 * TODO(waihong): Comment on how long this take to
+			 * timeout
+			 */
+			sdelay(100);
+			i--;
+		}
+		if (!i)
+			return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+		writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
+
+		writel(0, &phy0_ctrl->phy_con14);
+		writel(0, &phy1_ctrl->phy_con14);
+
+		val = (mem->ctrl_start_point <<
+				PHY_CON12_CTRL_START_POINT_SHIFT) |
+			(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+			(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+			(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+			(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+			(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+		writel(val, &phy0_ctrl->phy_con12);
+		writel(val, &phy1_ctrl->phy_con12);
+
+		update_reset_dll(dmc, DDR_MODE_DDR3);
+	}
+
+	/* Send PALL command */
+	dmc_config_prech(mem, dmc);
+
+	writel(mem->memcontrol, &dmc->memcontrol);
+
+	/* Set DMC Concontrol and enable auto-refresh counter */
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+		| (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
+	return 0;
+}
diff --git a/board/samsung/arndale/lowlevel_init.S b/board/samsung/arndale/lowlevel_init.S
new file mode 100644
index 0000000..4fa73a7
--- /dev/null
+++ b/board/samsung/arndale/lowlevel_init.S
@@ -0,0 +1,92 @@ 
+/*
+ * Lowlevel setup for Arndale board based on Exynos5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+_TEXT_BASE:
+	.word	CONFIG_SYS_TEXT_BASE
+
+	.globl lowlevel_init
+lowlevel_init:
+
+	/* use iRAM stack in bl2 */
+	ldr	sp, =CONFIG_IRAM_STACK
+	stmdb	r13!, {ip,lr}
+
+	/* check reset status */
+	ldr	r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET)
+	ldr	r1, [r0]
+
+	/* AFTR wakeup reset */
+	ldr	r2, =S5P_CHECK_DIDLE
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* Sleep wakeup reset */
+	ldr	r2, =S5P_CHECK_SLEEP
+	cmp	r1, r2
+	beq	wakeup_reset
+
+	/*
+	 * If U-boot is already running in RAM, no need to relocate U-Boot.
+	 * Memory controller must be configured before relocating U-Boot
+	 * in ram.
+	 */
+	ldr	r0, =0x0ffffff		/* r0 <- Mask Bits*/
+	bic	r1, pc, r0		/* pc <- current addr of code */
+					/* r1 <- unmasked bits of pc */
+	ldr	r2, _TEXT_BASE		/* r2 <- original base addr in ram */
+	bic	r2, r2, r0		/* r2 <- unmasked bits of r2*/
+	cmp	r1, r2			/* compare r1, r2 */
+	beq	1f			/* r0 == r1 then skip sdram init */
+
+	/* init system clock */
+	bl	system_clock_init
+
+	/* Memory initialize */
+	bl	mem_ctrl_init
+1:
+	bl	arch_cpu_init
+	bl	tzpc_init
+	ldmia	r13!, {ip,pc}
+
+wakeup_reset:
+	bl	system_clock_init
+	bl	mem_ctrl_init
+	bl	arch_cpu_init
+	bl	tzpc_init
+
+exit_wakeup:
+	/* Load return address and jump to kernel */
+	ldr	r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET)
+
+	/* r1 = physical address of exynos5_cpu_resume function*/
+	ldr	r1, [r0]
+
+	/* Jump to kernel */
+	mov	pc, r1
+	nop
+	nop
diff --git a/board/samsung/arndale/setup.h b/board/samsung/arndale/setup.h
new file mode 100644
index 0000000..f68dd75
--- /dev/null
+++ b/board/samsung/arndale/setup.h
@@ -0,0 +1,569 @@ 
+/*
+ * Machine Specific Values for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ARNDALE_SETUP_H
+#define _ARNDALE_SETUP_H
+
+#include <config.h>
+#include <asm/arch/dmc.h>
+
+/* APLL_CON1	*/
+#define APLL_CON1_VAL	(0x00203800)
+
+/* MPLL_CON1	*/
+#define MPLL_CON1_VAL   (0x00203800)
+
+/* CPLL_CON1	*/
+#define CPLL_CON1_VAL	(0x00203800)
+
+/* GPLL_CON1	*/
+#define GPLL_CON1_VAL	(0x00203800)
+
+/* EPLL_CON1, CON2	*/
+#define EPLL_CON1_VAL	0x00000000
+#define EPLL_CON2_VAL	0x00000080
+
+/* VPLL_CON1, CON2	*/
+#define VPLL_CON1_VAL	0x00000000
+#define VPLL_CON2_VAL	0x00000080
+
+/* BPLL_CON1	*/
+#define BPLL_CON1_VAL	0x00203800
+
+/* Set PLL */
+#define set_pll(mdiv, pdiv, sdiv)	(1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
+
+/* CLK_SRC_CPU	*/
+/* 0 = MOUTAPLL,  1 = SCLKMPLL	*/
+#define MUX_HPM_SEL             0
+#define MUX_CPU_SEL             0
+#define MUX_APLL_SEL            1
+
+#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20)    \
+				| (MUX_CPU_SEL << 16)  \
+				| (MUX_APLL_SEL))
+
+/* MEMCONTROL register bit fields */
+#define DMC_MEMCONTROL_CLK_STOP_DISABLE	(0 << 0)
+#define DMC_MEMCONTROL_DPWRDN_DISABLE	(0 << 1)
+#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE	(0 << 2)
+#define DMC_MEMCONTROL_TP_DISABLE	(0 << 4)
+#define DMC_MEMCONTROL_DSREF_DISABLE	(0 << 5)
+#define DMC_MEMCONTROL_DSREF_ENABLE	(1 << 5)
+#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x)    (x << 6)
+
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3  (7 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_DDR3    (6 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2  (5 << 8)
+
+#define DMC_MEMCONTROL_MEM_WIDTH_32BIT  (2 << 12)
+
+#define DMC_MEMCONTROL_NUM_CHIP_1       (0 << 16)
+#define DMC_MEMCONTROL_NUM_CHIP_2       (1 << 16)
+
+#define DMC_MEMCONTROL_BL_8             (3 << 20)
+#define DMC_MEMCONTROL_BL_4             (2 << 20)
+
+#define DMC_MEMCONTROL_PZQ_DISABLE      (0 << 24)
+
+#define DMC_MEMCONTROL_MRR_BYTE_7_0     (0 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_15_8    (1 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_23_16   (2 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_31_24   (3 << 25)
+
+/* MEMCONFIG0 register bit fields */
+#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED     (1 << 12)
+#define DMC_MEMCONFIGx_CHIP_COL_10              (3 << 8)
+#define DMC_MEMCONFIGx_CHIP_ROW_14              (2 << 4)
+#define DMC_MEMCONFIGx_CHIP_ROW_15              (3 << 4)
+#define DMC_MEMCONFIGx_CHIP_BANK_8              (3 << 0)
+
+#define DMC_MEMBASECONFIGx_CHIP_BASE(x)         (x << 16)
+#define DMC_MEMBASECONFIGx_CHIP_MASK(x)         (x << 0)
+#define DMC_MEMBASECONFIG_VAL(x)        (       \
+	DMC_MEMBASECONFIGx_CHIP_BASE(x) |       \
+	DMC_MEMBASECONFIGx_CHIP_MASK(0x780)     \
+)
+
+#define DMC_MEMBASECONFIG0_VAL  DMC_MEMBASECONFIG_VAL(0x40)
+#define DMC_MEMBASECONFIG1_VAL  DMC_MEMBASECONFIG_VAL(0x80)
+
+#define DMC_PRECHCONFIG_VAL             0xFF000000
+#define DMC_PWRDNCONFIG_VAL             0xFFFF00FF
+
+#define DMC_CONCONTROL_RESET_VAL	0x0FFF0000
+#define DFI_INIT_START		(1 << 28)
+#define EMPTY			(1 << 8)
+#define AREF_EN			(1 << 5)
+
+#define DFI_INIT_COMPLETE_CHO	(1 << 2)
+#define DFI_INIT_COMPLETE_CH1	(1 << 3)
+
+#define RDLVL_COMPLETE_CHO	(1 << 14)
+#define RDLVL_COMPLETE_CH1	(1 << 15)
+
+#define CLK_STOP_EN	(1 << 0)
+#define DPWRDN_EN	(1 << 1)
+#define DSREF_EN	(1 << 5)
+
+/* COJCONTROL register bit fields */
+#define DMC_CONCONTROL_IO_PD_CON_DISABLE	(0 << 3)
+#define DMC_CONCONTROL_AREF_EN_DISABLE		(0 << 5)
+#define DMC_CONCONTROL_EMPTY_DISABLE		(0 << 8)
+#define DMC_CONCONTROL_EMPTY_ENABLE		(1 << 8)
+#define DMC_CONCONTROL_RD_FETCH_DISABLE		(0x0 << 12)
+#define DMC_CONCONTROL_TIMEOUT_LEVEL0		(0xFFF << 16)
+#define DMC_CONCONTROL_DFI_INIT_START_DISABLE	(0 << 28)
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL	((ARM2_RATIO << 28)             \
+				| (APLL_RATIO << 24)            \
+				| (PCLK_DBG_RATIO << 20)        \
+				| (ATB_RATIO << 16)             \
+				| (PERIPH_RATIO << 12)          \
+				| (ACP_RATIO << 8)              \
+				| (CPUD_RATIO << 4)             \
+				| (ARM_RATIO))
+
+
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL              0x66666
+#define CLK_DIV_FSYS0_VAL	       0x0BB00000
+
+/* CLK_DIV_CPU1	*/
+#define HPM_RATIO               0x2
+#define COPY_RATIO              0x0
+
+/* CLK_DIV_CPU1 = 0x00000003 */
+#define CLK_DIV_CPU1_VAL        ((HPM_RATIO << 4)		\
+				| (COPY_RATIO))
+
+/* CLK_SRC_CORE0 */
+#define CLK_SRC_CORE0_VAL       0x00000000
+
+/* CLK_SRC_CORE1 */
+#define CLK_SRC_CORE1_VAL       0x100
+
+/* CLK_DIV_CORE0 */
+#define CLK_DIV_CORE0_VAL       0x00120000
+
+/* CLK_DIV_CORE1 */
+#define CLK_DIV_CORE1_VAL       0x07070700
+
+/* CLK_DIV_SYSRGT */
+#define CLK_DIV_SYSRGT_VAL      0x00000111
+
+/* CLK_DIV_ACP */
+#define CLK_DIV_ACP_VAL         0x12
+
+/* CLK_DIV_SYSLFT */
+#define CLK_DIV_SYSLFT_VAL      0x00000311
+
+/* CLK_SRC_CDREX */
+#define CLK_SRC_CDREX_VAL       0x1
+
+/* CLK_DIV_CDREX */
+#define MCLK_CDREX2_RATIO       0x0
+#define ACLK_EFCON_RATIO        0x1
+#define MCLK_DPHY_RATIO		0x1
+#define MCLK_CDREX_RATIO	0x1
+#define ACLK_C2C_200_RATIO	0x1
+#define C2C_CLK_400_RATIO	0x1
+#define PCLK_CDREX_RATIO	0x1
+#define ACLK_CDREX_RATIO	0x1
+
+#define CLK_DIV_CDREX_VAL	((MCLK_DPHY_RATIO << 24)        \
+				| (C2C_CLK_400_RATIO << 6)	\
+				| (PCLK_CDREX_RATIO << 4)	\
+				| (ACLK_CDREX_RATIO))
+
+/* CLK_SRC_TOP0	*/
+#define MUX_ACLK_300_GSCL_SEL           0x0
+#define MUX_ACLK_300_GSCL_MID_SEL       0x0
+#define MUX_ACLK_400_G3D_MID_SEL        0x0
+#define MUX_ACLK_333_SEL	        0x0
+#define MUX_ACLK_300_DISP1_SEL	        0x0
+#define MUX_ACLK_300_DISP1_MID_SEL      0x0
+#define MUX_ACLK_200_SEL	        0x0
+#define MUX_ACLK_166_SEL	        0x0
+#define CLK_SRC_TOP0_VAL	((MUX_ACLK_300_GSCL_SEL  << 25)		\
+				| (MUX_ACLK_300_GSCL_MID_SEL << 24)	\
+				| (MUX_ACLK_400_G3D_MID_SEL << 20)	\
+				| (MUX_ACLK_333_SEL << 16)		\
+				| (MUX_ACLK_300_DISP1_SEL << 15)	\
+				| (MUX_ACLK_300_DISP1_MID_SEL << 14)	\
+				| (MUX_ACLK_200_SEL << 12)		\
+				| (MUX_ACLK_166_SEL << 8))
+
+/* CLK_SRC_TOP1	*/
+#define MUX_ACLK_400_G3D_SEL            0x1
+#define MUX_ACLK_400_ISP_SEL            0x0
+#define MUX_ACLK_400_IOP_SEL            0x0
+#define MUX_ACLK_MIPI_HSI_TXBASE_SEL    0x0
+#define MUX_ACLK_300_GSCL_MID1_SEL      0x0
+#define MUX_ACLK_300_DISP1_MID1_SEL     0x0
+#define CLK_SRC_TOP1_VAL	((MUX_ACLK_400_G3D_SEL << 28)           \
+				|(MUX_ACLK_400_ISP_SEL << 24)           \
+				|(MUX_ACLK_400_IOP_SEL << 20)           \
+				|(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16)   \
+				|(MUX_ACLK_300_GSCL_MID1_SEL << 12)     \
+				|(MUX_ACLK_300_DISP1_MID1_SEL << 8))
+
+/* CLK_SRC_TOP2 */
+#define MUX_GPLL_SEL                    0x1
+#define MUX_BPLL_USER_SEL               0x0
+#define MUX_MPLL_USER_SEL               0x0
+#define MUX_VPLL_SEL                    0x1
+#define MUX_EPLL_SEL                    0x1
+#define MUX_CPLL_SEL                    0x1
+#define VPLLSRC_SEL                     0x0
+#define CLK_SRC_TOP2_VAL	((MUX_GPLL_SEL << 28)		\
+				| (MUX_BPLL_USER_SEL << 24)	\
+				| (MUX_MPLL_USER_SEL << 20)	\
+				| (MUX_VPLL_SEL << 16)	        \
+				| (MUX_EPLL_SEL << 12)	        \
+				| (MUX_CPLL_SEL << 8)           \
+				| (VPLLSRC_SEL))
+/* CLK_SRC_TOP3 */
+#define MUX_ACLK_333_SUB_SEL            0x1
+#define MUX_ACLK_400_SUB_SEL            0x1
+#define MUX_ACLK_266_ISP_SUB_SEL        0x1
+#define MUX_ACLK_266_GPS_SUB_SEL        0x0
+#define MUX_ACLK_300_GSCL_SUB_SEL       0x1
+#define MUX_ACLK_266_GSCL_SUB_SEL       0x1
+#define MUX_ACLK_300_DISP1_SUB_SEL      0x1
+#define MUX_ACLK_200_DISP1_SUB_SEL      0x1
+#define CLK_SRC_TOP3_VAL	((MUX_ACLK_333_SUB_SEL << 24)	        \
+				| (MUX_ACLK_400_SUB_SEL << 20)	        \
+				| (MUX_ACLK_266_ISP_SUB_SEL << 16)	\
+				| (MUX_ACLK_266_GPS_SUB_SEL << 12)      \
+				| (MUX_ACLK_300_GSCL_SUB_SEL << 10)     \
+				| (MUX_ACLK_266_GSCL_SUB_SEL << 8)      \
+				| (MUX_ACLK_300_DISP1_SUB_SEL << 6)     \
+				| (MUX_ACLK_200_DISP1_SUB_SEL << 4))
+
+/* CLK_DIV_TOP0	*/
+#define ACLK_300_DISP1_RATIO	0x2
+#define ACLK_400_G3D_RATIO	0x0
+#define ACLK_333_RATIO		0x0
+#define ACLK_266_RATIO		0x2
+#define ACLK_200_RATIO		0x3
+#define ACLK_166_RATIO		0x1
+#define ACLK_133_RATIO		0x1
+#define ACLK_66_RATIO		0x5
+
+#define CLK_DIV_TOP0_VAL	((ACLK_300_DISP1_RATIO << 28)	\
+				| (ACLK_400_G3D_RATIO << 24)	\
+				| (ACLK_333_RATIO  << 20)	\
+				| (ACLK_266_RATIO << 16)	\
+				| (ACLK_200_RATIO << 12)	\
+				| (ACLK_166_RATIO << 8)		\
+				| (ACLK_133_RATIO << 4)		\
+				| (ACLK_66_RATIO))
+
+/* CLK_DIV_TOP1	*/
+#define ACLK_MIPI_HSI_TX_BASE_RATIO     0x3
+#define ACLK_66_PRE_RATIO               0x1
+#define ACLK_400_ISP_RATIO              0x1
+#define ACLK_400_IOP_RATIO              0x1
+#define ACLK_300_GSCL_RATIO             0x2
+
+#define CLK_DIV_TOP1_VAL	((ACLK_MIPI_HSI_TX_BASE_RATIO << 28)	\
+				| (ACLK_66_PRE_RATIO << 24)		\
+				| (ACLK_400_ISP_RATIO  << 20)		\
+				| (ACLK_400_IOP_RATIO << 16)		\
+				| (ACLK_300_GSCL_RATIO << 12))
+
+/* APLL_LOCK	*/
+#define APLL_LOCK_VAL	(0x546)
+/* MPLL_LOCK	*/
+#define MPLL_LOCK_VAL	(0x546)
+/* CPLL_LOCK	*/
+#define CPLL_LOCK_VAL	(0x546)
+/* GPLL_LOCK	*/
+#define GPLL_LOCK_VAL	(0x546)
+/* EPLL_LOCK	*/
+#define EPLL_LOCK_VAL	(0x3A98)
+/* VPLL_LOCK	*/
+#define VPLL_LOCK_VAL	(0x3A98)
+/* BPLL_LOCK	*/
+#define BPLL_LOCK_VAL	(0x546)
+
+#define MUX_APLL_SEL_MASK	(1 << 0)
+#define MUX_MPLL_SEL_MASK	(1 << 8)
+#define MPLL_SEL_MOUT_MPLLFOUT	(2 << 8)
+#define MUX_CPLL_SEL_MASK	(1 << 8)
+#define MUX_EPLL_SEL_MASK	(1 << 12)
+#define MUX_VPLL_SEL_MASK	(1 << 16)
+#define MUX_GPLL_SEL_MASK	(1 << 28)
+#define MUX_BPLL_SEL_MASK	(1 << 0)
+#define MUX_HPM_SEL_MASK	(1 << 20)
+#define HPM_SEL_SCLK_MPLL	(1 << 21)
+#define APLL_CON0_LOCKED	(1 << 29)
+#define MPLL_CON0_LOCKED	(1 << 29)
+#define BPLL_CON0_LOCKED	(1 << 29)
+#define CPLL_CON0_LOCKED	(1 << 29)
+#define EPLL_CON0_LOCKED	(1 << 29)
+#define GPLL_CON0_LOCKED	(1 << 29)
+#define VPLL_CON0_LOCKED	(1 << 29)
+#define CLK_REG_DISABLE		0x0
+#define TOP2_VAL		0x0110000
+
+/* CLK_SRC_PERIC0 */
+#define PWM_SEL		0
+#define UART3_SEL	6
+#define UART2_SEL	6
+#define UART1_SEL	6
+#define UART0_SEL	6
+/* SRC_CLOCK = SCLK_MPLL */
+#define CLK_SRC_PERIC0_VAL	((PWM_SEL << 24)        \
+				| (UART3_SEL << 12)     \
+				| (UART2_SEL << 8)       \
+				| (UART1_SEL << 4)      \
+				| (UART0_SEL))
+
+/* CLK_SRC_PERIC1 */
+/* SRC_CLOCK = SCLK_MPLL */
+#define SPI0_SEL		6
+#define SPI1_SEL		6
+#define SPI2_SEL		6
+#define CLK_SRC_PERIC1_VAL	((SPI2_SEL << 24) \
+				| (SPI1_SEL << 20) \
+				| (SPI0_SEL << 16))
+
+/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
+#define SPI0_ISP_SEL		6
+#define SPI1_ISP_SEL		6
+#define SCLK_SRC_ISP_VAL	(SPI1_ISP_SEL << 4) \
+				| (SPI0_ISP_SEL << 0)
+
+/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
+#define SPI0_ISP_RATIO		0xf
+#define SPI1_ISP_RATIO		0xf
+#define SCLK_DIV_ISP_VAL	(SPI1_ISP_RATIO << 12) \
+				| (SPI0_ISP_RATIO << 0)
+
+/* CLK_DIV_PERIL0	*/
+#define UART5_RATIO	7
+#define UART4_RATIO	7
+#define UART3_RATIO	7
+#define UART2_RATIO	7
+#define UART1_RATIO	7
+#define UART0_RATIO	7
+
+#define CLK_DIV_PERIC0_VAL	((UART3_RATIO << 12)    \
+				| (UART2_RATIO << 8)    \
+				| (UART1_RATIO << 4)    \
+				| (UART0_RATIO))
+/* CLK_DIV_PERIC1 */
+#define SPI1_RATIO		0x7
+#define SPI0_RATIO		0xf
+#define SPI1_SUB_RATIO		0x0
+#define SPI0_SUB_RATIO		0x0
+#define CLK_DIV_PERIC1_VAL	((SPI1_SUB_RATIO << 24) \
+				| ((SPI1_RATIO << 16) \
+				| (SPI0_SUB_RATIO << 8) \
+				| (SPI0_RATIO << 0)))
+
+/* CLK_DIV_PERIC2 */
+#define SPI2_RATIO		0xf
+#define SPI2_SUB_RATIO		0x0
+#define CLK_DIV_PERIC2_VAL	((SPI2_SUB_RATIO << 8) \
+				| (SPI2_RATIO << 0))
+
+/* CLK_DIV_PERIC3 */
+#define PWM_RATIO		8
+#define CLK_DIV_PERIC3_VAL	(PWM_RATIO << 0)
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO_MASK		0xf
+#define MMC2_RATIO_VAL		0x3
+#define MMC2_RATIO_OFFSET	0
+
+#define MMC2_PRE_RATIO_MASK	0xff
+#define MMC2_PRE_RATIO_VAL	0x9
+#define MMC2_PRE_RATIO_OFFSET	8
+
+#define MMC3_RATIO_MASK		0xf
+#define MMC3_RATIO_VAL		0x1
+#define MMC3_RATIO_OFFSET	16
+
+#define MMC3_PRE_RATIO_MASK	0xff
+#define MMC3_PRE_RATIO_VAL	0x0
+#define MMC3_PRE_RATIO_OFFSET	24
+
+/* CLK_SRC_LEX */
+#define CLK_SRC_LEX_VAL         0x0
+
+/* CLK_DIV_LEX */
+#define CLK_DIV_LEX_VAL         0x10
+
+/* CLK_DIV_R0X */
+#define CLK_DIV_R0X_VAL         0x10
+
+/* CLK_DIV_L0X */
+#define CLK_DIV_R1X_VAL         0x10
+
+/* CLK_DIV_ISP0 */
+#define CLK_DIV_ISP0_VAL        0x31
+
+/* CLK_DIV_ISP1 */
+#define CLK_DIV_ISP1_VAL        0x0
+
+/* CLK_DIV_ISP2 */
+#define CLK_DIV_ISP2_VAL        0x1
+
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL	0x6
+
+/*
+ * DIV_DISP1_0
+ * For DP, divisor should be 2
+ */
+#define CLK_DIV_DISP1_0_FIMD1	(2 << 0)
+
+/* CLK_GATE_IP_DISP1 */
+#define CLK_GATE_DP1_ALLOW	(1 << 4)
+
+#define DDR3PHY_CTRL_PHY_RESET	(1 << 0)
+#define DDR3PHY_CTRL_PHY_RESET_OFF	(0 << 0)
+
+#define PHY_CON0_RESET_VAL	0x17020a40
+#define P0_CMD_EN		(1 << 14)
+#define BYTE_RDLVL_EN		(1 << 13)
+#define CTRL_SHGATE		(1 << 8)
+
+#define PHY_CON1_RESET_VAL	0x09210100
+#define CTRL_GATEDURADJ_MASK	(0xf << 20)
+
+#define PHY_CON2_RESET_VAL	0x00010004
+#define INIT_DESKEW_EN		(1 << 6)
+#define RDLVL_GATE_EN		(1 << 24)
+
+/*ZQ Configurations */
+#define PHY_CON16_RESET_VAL	0x08000304
+
+#define ZQ_CLK_DIV_EN		(1 << 18)
+#define ZQ_MANUAL_STR		(1 << 1)
+#define ZQ_DONE			(1 << 0)
+
+#define CTRL_RDLVL_GATE_ENABLE	1
+#define CTRL_RDLVL_GATE_DISABLE	1
+
+/* Direct Command */
+#define DIRECT_CMD_NOP			0x07000000
+#define DIRECT_CMD_PALL			0x01000000
+#define DIRECT_CMD_ZQINIT		0x0a000000
+#define DIRECT_CMD_CHANNEL_SHIFT	28
+#define DIRECT_CMD_CHIP_SHIFT		20
+
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL	0x0
+#define MEM_TERM_EN	(1 << 31)	/* Termination enable for memory */
+#define PHY_TERM_EN	(1 << 30)	/* Termination enable for PHY */
+#define DMC_CTRL_SHGATE	(1 << 29)	/* Duration of DQS gating signal */
+#define FP_RSYNC	(1 << 3)	/* Force DLL resyncronization */
+
+/* Driver strength for CK, CKE, CS & CA */
+#define IMP_OUTPUT_DRV_40_OHM	0x5
+#define IMP_OUTPUT_DRV_30_OHM	0x7
+#define CA_CK_DRVR_DS_OFFSET	9
+#define CA_CKE_DRVR_DS_OFFSET	6
+#define CA_CS_DRVR_DS_OFFSET	3
+#define CA_ADR_DRVR_DS_OFFSET	0
+
+#define PHY_CON42_CTRL_BSTLEN_SHIFT	8
+#define PHY_CON42_CTRL_RDLAT_SHIFT	0
+
+struct mem_timings;
+
+/* Errors that we can encourter in low-level setup */
+enum {
+	SETUP_ERR_OK,
+	SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
+	SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
+};
+
+/*
+ * Memory variant specific initialization code
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param mem_iv_size	Memory interleaving size is a configurable parameter
+ *			which the DMC uses to decide how to split a memory
+ *			chunk into smaller chunks to support concurrent
+ *			accesses; may vary across boards.
+ * @return 0 if ok, SETUP_ERR_... if there is a problem
+ */
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
+
+/*
+ * Configure ZQ I/O interface
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param phy0_ctrl	Pointer to struct containing PHY0 control reg
+ * @param phy1_ctrl	Pointer to struct containing PHY1 control reg
+ * @return 0 if ok, -1 on error
+ */
+int dmc_config_zq(struct mem_timings *mem,
+		  struct exynos5_phy_control *phy0_ctrl,
+		  struct exynos5_phy_control *phy1_ctrl);
+
+/*
+ * Send NOP and MRS/EMRS Direct commands
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param dmc		Pointer to struct of DMC registers
+ */
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Send PALL Direct commands
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param dmc		Pointer to struct of DMC registers
+ */
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Configure the memconfig and membaseconfig registers
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param exynos5_dmc	Pointer to struct of DMC registers
+ */
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Reset the DLL. This function is common between DDR3 and LPDDR2.
+ * However, the reset value is different. So we are passing a flag
+ * ddr_mode to distinguish between LPDDR2 and DDR3.
+ *
+ * @param exynos5_dmc	Pointer to struct of DMC registers
+ * @param ddr_mode	Type of DDR memory
+ */
+void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
+
+void sdelay(unsigned long);
+void mem_ctrl_init(void);
+void system_clock_init(void);
+#endif
diff --git a/board/samsung/dts/exynos5250-arndale.dts b/board/samsung/dts/exynos5250-arndale.dts
new file mode 100644
index 0000000..9b4d6b2
--- /dev/null
+++ b/board/samsung/dts/exynos5250-arndale.dts
@@ -0,0 +1,36 @@ 
+/*
+ * SAMSUNG Arndale board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ ARCH_CPU_DTS
+
+/ {
+	model = "SAMSUNG Arndale board based on EXYNOS5250";
+	compatible = "samsung,arndale", "samsung,exynos5250";
+
+	mmc@12200000 {
+		samsung,bus-width = <8>;
+		samsung,timing = <1 3 3>;
+	};
+
+	mmc@12210000 {
+		status = "disabled";
+	};
+
+	mmc@12220000 {
+		samsung,bus-width = <4>;
+		samsung,timing = <1 2 3>;
+	};
+
+	mmc@12230000 {
+		status = "disabled";
+	};
+};
diff --git a/boards.cfg b/boards.cfg
index 54357eb..572b242 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -288,6 +288,7 @@  origen			     arm	 armv7	     origen		 samsung	exynos
 s5pc210_universal            arm         armv7       universal_c210      samsung        exynos
 snow			     arm	 armv7	     smdk5250		 samsung	exynos
 smdk5250		     arm	 armv7	     smdk5250		 samsung	exynos
+arndale		     	     arm	 armv7	     arndale		 samsung	exynos
 smdkv310		     arm	 armv7	     smdkv310		 samsung	exynos
 trats                        arm         armv7       trats               samsung        exynos
 harmony                      arm         armv7:arm720t harmony           nvidia         tegra20
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
new file mode 100644
index 0000000..caa83b8
--- /dev/null
+++ b/include/configs/arndale.h
@@ -0,0 +1,39 @@ 
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG Arndale board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_ARNDALE_H
+#define __CONFIG_ARNDALE_H
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE	exynos5250-arndale
+
+#define CONFIG_ARNDALE
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SERIAL2
+#define CONFIG_IDENT_STRING		" for Arndale"
+
+#include <configs/exynos5250-dt.h>
+
+#endif	/* __CONFIG_ARNDALE_H */
diff --git a/tools/Makefile b/tools/Makefile
index c5952fc..ab7d339 100644
--- a/tools/Makefile
+++ b/tools/Makefile
@@ -69,6 +69,7 @@  BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
 BIN_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl$(SFX)
+BIN_FILES-$(CONFIG_ARNDALE) += mkarndalespl$(SFX)
 BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -99,6 +100,7 @@  NOPED_OBJ_FILES-y += omapimage.o
 NOPED_OBJ_FILES-y += mkenvimage.o
 NOPED_OBJ_FILES-y += mkimage.o
 OBJ_FILES-$(CONFIG_SMDK5250) += mkexynosspl.o
+OBJ_FILES-$(CONFIG_ARNDALE) += mkexynosspl.o
 OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
 OBJ_FILES-$(CONFIG_MX28) += mxsboot.o
 OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o