| Message ID | 20210615074543.26700-10-bhupesh.sharma@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2,01/10] dt-bindings: qcom: rpmh-regulator: Add compatible for SA8155p-adp board pmic | expand |
On Tue 15 Jun 02:45 CDT 2021, Bhupesh Sharma wrote: > Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc > nodes. > > Cc: Linus Walleij <linus.walleij@linaro.org> > Cc: Liam Girdwood <lgirdwood@gmail.com> > Cc: Mark Brown <broonie@kernel.org> > Cc: Bjorn Andersson <bjorn.andersson@linaro.org> > Cc: Vinod Koul <vkoul@kernel.org> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: Andy Gross <agross@kernel.org> > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Regards, Bjorn > --- > arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++ > 1 file changed, 107 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi > new file mode 100644 > index 000000000000..0c7d7a66c0b5 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi > @@ -0,0 +1,107 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2021, Linaro Limited > + */ > + > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pmm8155au-2-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pmm8155au_2_temp>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + > + trip2 { > + temperature = <145000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > + }; > +}; > + > +&spmi_bus { > + pmic@4 { > + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; > + reg = <0x4 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + power-on@800 { > + compatible = "qcom,pm8916-pon"; > + reg = <0x0800>; > + > + status = "disabled"; > + }; > + > + pmm8155au_2_temp: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; > + io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>; > + io-channel-names = "thermal"; > + #thermal-sensor-cells = <0>; > + }; > + > + pmm8155au_2_adc: adc@3100 { > + compatible = "qcom,spmi-adc5"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + die-temp@6 { > + reg = <ADC5_DIE_TEMP>; > + qcom,pre-scaling = <1 1>; > + label = "die_temp"; > + }; > + }; > + > + pmm8155au_2_gpios: gpio@c000 { > + compatible = "qcom,pmm8155au-gpio"; > + reg = <0xc000>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmic@5 { > + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; > + reg = <0x5 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > +}; > -- > 2.31.1 >
diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi new file mode 100644 index 000000000000..0c7d7a66c0b5 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi @@ -0,0 +1,107 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pmm8155au-2-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmm8155au_2_temp>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + pmic@4 { + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + pmm8155au_2_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pmm8155au_2_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + pmm8155au_2_gpios: gpio@c000 { + compatible = "qcom,pmm8155au-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@5 { + compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +};
Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc nodes. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Vinod Koul <vkoul@kernel.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Andy Gross <agross@kernel.org> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org> --- arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++ 1 file changed, 107 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi -- 2.31.1