diff mbox series

[v9,1/2] dt-bindings: leds: Add Qualcomm Light Pulse Generator binding

Message ID 20210623035039.772660-1-bjorn.andersson@linaro.org
State New
Headers show
Series [v9,1/2] dt-bindings: leds: Add Qualcomm Light Pulse Generator binding | expand

Commit Message

Bjorn Andersson June 23, 2021, 3:50 a.m. UTC
This adds the binding document describing the three hardware blocks
related to the Light Pulse Generator found in a wide range of Qualcomm
PMICs.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v8:
- None

Changes since v7:
- Added qcom,pmc8180c-lpg
- Defined constraints for qcom,power-source
- Changes qcom,dtest to matrix and added constraints
- Changed example from LED_COLOR_ID_MULTI to LED_COLOR_ID_RGB

 .../bindings/leds/leds-qcom-lpg.yaml          | 164 ++++++++++++++++++
 1 file changed, 164 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml

Comments

Rob Herring June 24, 2021, 9:39 p.m. UTC | #1
On Tue, 22 Jun 2021 20:50:38 -0700, Bjorn Andersson wrote:
> This adds the binding document describing the three hardware blocks
> related to the Light Pulse Generator found in a wide range of Qualcomm
> PMICs.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> 
> Changes since v8:
> - None
> 
> Changes since v7:
> - Added qcom,pmc8180c-lpg
> - Defined constraints for qcom,power-source
> - Changes qcom,dtest to matrix and added constraints
> - Changed example from LED_COLOR_ID_MULTI to LED_COLOR_ID_RGB
> 
>  .../bindings/leds/leds-qcom-lpg.yaml          | 164 ++++++++++++++++++
>  1 file changed, 164 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>
Marek Behún June 24, 2021, 11:19 p.m. UTC | #2
On Tue, 22 Jun 2021 20:50:38 -0700
Bjorn Andersson <bjorn.andersson@linaro.org> wrote:

> +++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml


The file name should be based on one of the compatible strings, for
example the first one:
  qcom,pm8150b-lpg.yaml

> +      led@1 {

> +        reg = <1>;

> +        label = "green:user1";

> +      };


`label` is deprecated, please don't use in new bindings in examples.
Instead use color, function and function-enumerator, i.e.

  color = <LED_COLOR_ID_GREEN>;
  function = LED_FUNCTION_xxx;
  function-enumerator = <N>;
Bjorn Andersson June 24, 2021, 11:44 p.m. UTC | #3
On Thu 24 Jun 18:19 CDT 2021, Marek Behun wrote:

> On Tue, 22 Jun 2021 20:50:38 -0700
> Bjorn Andersson <bjorn.andersson@linaro.org> wrote:
> 
> > +++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
> 
> The file name should be based on one of the compatible strings, for
> example the first one:
>   qcom,pm8150b-lpg.yaml
> 

The majority of the files in leds/ are named leds-*.yaml, is this a new
scheme for LED bindings?

> > +      led@1 {
> > +        reg = <1>;
> > +        label = "green:user1";
> > +      };
> 
> `label` is deprecated,

Sorry, I missed the comment in the middle of the description about this.
Is there any particular reason why this isn't marked deprecated: true?

> please don't use in new bindings in examples.
> Instead use color, function and function-enumerator, i.e.
> 
>   color = <LED_COLOR_ID_GREEN>;
>   function = LED_FUNCTION_xxx;
>   function-enumerator = <N>;
> 

Can you point me to something helping me regarding what "function" to
use?

For this particular devboard that the example comes from I have 4 LEDs
that are named "user1", "user2", "user3" and "user4" in the board
documentation. I can make up whatever for the example, but I would like
to get the following dts additions follow the expected guidelines.

Regards,
Bjorn
Alexander Dahl June 25, 2021, 8:39 a.m. UTC | #4
Hello Bjorn,

Am Thu, Jun 24, 2021 at 06:44:54PM -0500 schrieb Bjorn Andersson:
> On Thu 24 Jun 18:19 CDT 2021, Marek Behun wrote:

> > please don't use in new bindings in examples.

> > Instead use color, function and function-enumerator, i.e.

> > 

> >   color = <LED_COLOR_ID_GREEN>;

> >   function = LED_FUNCTION_xxx;

> >   function-enumerator = <N>;

> > 

> 

> Can you point me to something helping me regarding what "function" to

> use?

> 

> For this particular devboard that the example comes from I have 4 LEDs

> that are named "user1", "user2", "user3" and "user4" in the board

> documentation. I can make up whatever for the example, but I would like

> to get the following dts additions follow the expected guidelines.


I asked myself the same question in the past.  The wohle list is in
'include/dt-bindings/leds/common.h' and I in my personal project I
opted for LED_FUNCTION_INDICATOR, but yes, the confusion is real.

Greets
Alex
Uwe Kleine-König June 25, 2021, 1:15 p.m. UTC | #5
Hello Bjorn,

On Tue, Jun 22, 2021 at 08:50:39PM -0700, Bjorn Andersson wrote:
> +static const unsigned int lpg_clk_rates[] = {1024, 32768, 19200000};
> +static const unsigned int lpg_pre_divs[] = {1, 3, 5, 6};
> +
> +static int lpg_calc_freq(struct lpg_channel *chan, uint64_t period)
> +{
> +	unsigned int clk, best_clk = 0;
> +	unsigned int div, best_div = 0;
> +	unsigned int m, best_m = 0;
> +	unsigned int error;
> +	unsigned int best_err = UINT_MAX;
> +	u64 denom;
> +	u64 best_period = 0;
> +	u64 actual;
> +	u64 ratio;
> +	u64 nom;
> +
> +	/*
> +	 * The PWM period is determined by:
> +	 *
> +	 *          resolution * pre_div * 2^M
> +	 * period = --------------------------
> +	 *                   refclk
> +	 *
> +	 * With resolution fixed at 2^9 bits, pre_div = {1, 3, 5, 6} and
> +	 * M = [0..7].
> +	 *
> +	 * This allows for periods between 27uS and 381s, as the PWM framework
> +	 * wants a period of equal or lower length than requested, reject
> +	 * anything below 27uS.
> +	 */
> +	if (period <= (u64)NSEC_PER_SEC * LPG_RESOLUTION / 19200000)
> +		return -EINVAL;
> +
> +	/* Limit period to largest possible value, to avoid overflows */
> +	if (period > 381 * (u64)NSEC_PER_SEC)
> +		period = 381 * (u64)NSEC_PER_SEC;

Where does the magic 381 come from? This would be more obviously correct
if you write out the formula as you did for the check above.

> +	/*
> +	 * Search for the pre_div, clk and M by solving the rewritten formula
> +	 * for each clk and pre_div value:
> +	 *
> +	 *                       period * clk
> +	 * M = log2 -------------------------------------
> +	 *           NSEC_PER_SEC * pre_div * resolution
> +	 */
> +	for (clk = 0; clk < ARRAY_SIZE(lpg_clk_rates); clk++) {
> +		nom = period * lpg_clk_rates[clk];

nom is only used in this block, so the declaration can be put in here,
too. Ditto for at least ratio and actual.

> +
> +		for (div = 0; div < ARRAY_SIZE(lpg_pre_divs); div++) {
> +			denom = (u64)NSEC_PER_SEC * lpg_pre_divs[div] * (1 << 9);
> +
> +			if (nom < denom)
> +				continue;
> +
> +			ratio = div64_u64(nom, denom);
> +			m = ilog2(ratio);
> +			if (m > LPG_MAX_M)
> +				m = LPG_MAX_M;
> +
> +			actual = DIV_ROUND_UP_ULL(denom * (1 << m), lpg_clk_rates[clk]);
> +
> +			error = period - actual;
> +			if (error < best_err) {
> +				best_err = error;
> +
> +				best_div = div;
> +				best_m = m;
> +				best_clk = clk;
> +				best_period = actual;
> +			}
> +		}
> +	}
> +
> +	chan->clk = best_clk;
> +	chan->pre_div = best_div;
> +	chan->pre_div_exp = best_m;
> +	chan->period = best_period;
> +
> +	return 0;
> +}
> +
> +static void lpg_calc_duty(struct lpg_channel *chan, uint64_t duty)
> +{
> +	unsigned int max = LPG_RESOLUTION - 1;
> +	unsigned int val = div_u64(duty * max, chan->period);

You're losing precision here as chan->period is a rounded value.

duty * max might overflow.

> +	chan->pwm_value = min(val, max);
> +}
> [...]
> +static void lpg_apply(struct lpg_channel *chan)
> +{
> +	lpg_disable_glitch(chan);

Why do you have to do this?

> +	lpg_apply_freq(chan);
> +	lpg_apply_pwm_value(chan);
> +	lpg_apply_control(chan);
> +	lpg_apply_sync(chan);
> +	lpg_apply_lut_control(chan);
> +	lpg_enable_glitch(chan);
> +}
> [...]
> +/*
> + * Limitations:
> + * - Updating both duty and period is not done atomically, so the output signal
> + *   will momentarily be a mix of the settings.
> + */
> +static int lpg_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> +			 const struct pwm_state *state)
> +{
> +	struct lpg *lpg = container_of(chip, struct lpg, pwm);
> +	struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> +	int ret;
> +

You have to care for state->polarity here.

> +	ret = lpg_calc_freq(chan, state->period);
> +	if (ret < 0)
> +		return ret;
> +
> +	lpg_calc_duty(chan, state->duty_cycle);
> +	chan->enabled = state->enabled;
> +
> +	lpg_apply(chan);
> +
> +	triled_set(lpg, chan->triled_mask, chan->enabled ? chan->triled_mask : 0);
> +
> +	return 0;
> +}
> [...]
> +static int lpg_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np;
> +	struct lpg *lpg;
> +	int ret;
> +	int i;
> +
> +	lpg = devm_kzalloc(&pdev->dev, sizeof(*lpg), GFP_KERNEL);
> +	if (!lpg)
> +		return -ENOMEM;
> +
> +	lpg->data = of_device_get_match_data(&pdev->dev);
> +	if (!lpg->data)
> +		return -EINVAL;
> +
> +	lpg->dev = &pdev->dev;
> +
> +	lpg->map = dev_get_regmap(pdev->dev.parent, NULL);
> +	if (!lpg->map) {
> +		dev_err(&pdev->dev, "parent regmap unavailable\n");
> +		return -ENXIO;
> +	}
> +
> +	ret = lpg_init_channels(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_parse_dtest(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_init_triled(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_init_lut(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	for_each_available_child_of_node(pdev->dev.of_node, np) {
> +		ret = lpg_add_led(lpg, np);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	for (i = 0; i < lpg->num_channels; i++)
> +		lpg_apply_dtest(&lpg->channels[i]);

I wonder what all these register initialisations do. You should not do
anything that modifies the PWM output here that the bootloader might
have setup. Is this given?

> +
> +	ret = lpg_add_pwm(lpg);

The patch would be easier to review if you split it into a led part and
a pwm part. Then the responsibilities would be more clear, too.

> +	if (ret)
> +		return ret;
> +
> +	platform_set_drvdata(pdev, lpg);
> +
> +	return 0;

If you do the platform_set_drvdata() earlier you can just

	return ret;

here.

> +}

Best regards
Uwe
Matthias Kaehlcke Sept. 9, 2021, 3:18 p.m. UTC | #6
On Tue, Jun 22, 2021 at 08:50:38PM -0700, Bjorn Andersson wrote:
> This adds the binding document describing the three hardware blocks
> related to the Light Pulse Generator found in a wide range of Qualcomm
> PMICs.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> 
> Changes since v8:
> - None
> 
> Changes since v7:
> - Added qcom,pmc8180c-lpg
> - Defined constraints for qcom,power-source
> - Changes qcom,dtest to matrix and added constraints
> - Changed example from LED_COLOR_ID_MULTI to LED_COLOR_ID_RGB
> 
>  .../bindings/leds/leds-qcom-lpg.yaml          | 164 ++++++++++++++++++
>  1 file changed, 164 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
> 
> diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
> new file mode 100644
> index 000000000000..10aee61a7ffc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
> @@ -0,0 +1,164 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/leds-qcom-lpg.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Light Pulse Generator
> +
> +maintainers:
> +  - Bjorn Andersson <bjorn.andersson@linaro.org>
> +
> +description: >
> +  The Qualcomm Light Pulse Generator consists of three different hardware blocks;
> +  a ramp generator with lookup table, the light pulse generator and a three
> +  channel current sink. These blocks are found in a wide range of Qualcomm PMICs.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,pm8150b-lpg
> +      - qcom,pm8150l-lpg
> +      - qcom,pm8916-pwm
> +      - qcom,pm8941-lpg
> +      - qcom,pm8994-lpg
> +      - qcom,pmc8180c-lpg
> +      - qcom,pmi8994-lpg
> +      - qcom,pmi8998-lpg
> +
> +  "#pwm-cells":
> +    const: 2
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +  qcom,power-source:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      power-source used to drive the output, as defined in the datasheet.
> +      Should be specified if the TRILED block is present
> +    enum: [0, 1, 3]
> +
> +  qcom,dtest:
> +    $ref: /schemas/types.yaml#/definitions/uint32-matrix
> +    description: >
> +      A list of integer pairs, where each pair represent the dtest line the
> +      particular channel should be connected to and the flags denoting how the
> +      value should be outputed, as defined in the datasheet. The number of
> +      pairs should be the same as the number of channels.
> +    items:
> +      items:
> +        - description: dtest line to attach
> +        - description: flags for the attachment
> +
> +  multi-led:
> +    type: object
> +    $ref: leds-class-multicolor.yaml#
> +    properties:
> +      "#address-cells":
> +        const: 1
> +
> +      "#size-cells":
> +        const: 0
> +
> +      "^led@[0-9a-f]$":
> +        type: object
> +        $ref: common.yaml#
> +
> +patternProperties:
> +  "^led@[0-9a-f]$":
> +    type: object
> +    $ref: common.yaml#
> +
> +    properties:
> +      reg: true
> +
> +    required:
> +      - reg
> +
> +required:
> +  - compatible
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/leds/common.h>
> +
> +    lpg {
> +      compatible = "qcom,pmi8994-lpg";
> +
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      qcom,power-source = <1>;
> +
> +      qcom,dtest = <0 0>,
> +                   <0 0>,
> +                   <0 0>,
> +                   <4 1>;
> +
> +      led@1 {
> +        reg = <1>;
> +        label = "green:user1";
> +      };
> +
> +      led@2 {
> +        reg = <2>;
> +        label = "green:user0";
> +        default-state = "on";
> +      };
> +
> +      led@3 {
> +        reg = <3>;
> +        label = "green:user2";
> +      };
> +
> +      led@4 {
> +        reg = <4>;
> +        label = "green:user3";
> +      };
> +    };
> +  - |
> +    #include <dt-bindings/leds/common.h>
> +
> +    lpg {
> +      compatible = "qcom,pmi8994-lpg";
> +
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +
> +      qcom,power-source = <1>;
> +
> +      multi-led {
> +        color = <LED_COLOR_ID_RGB>;
> +        function = LED_FUNCTION_STATUS;
> +
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        led@1 {
> +          reg = <1>;
> +          color = <LED_COLOR_ID_RED>;
> +        };
> +
> +        led@2 {
> +          reg = <2>;
> +          color = <LED_COLOR_ID_GREEN>;
> +        };
> +
> +        led@3 {
> +          reg = <3>;
> +          color = <LED_COLOR_ID_BLUE>;
> +        };
> +      };
> +    };
> +  - |
> +    lpg {

nit: should the node be named 'lpg-pwm'?

IIUC a PMIC .dtsi could have both a 'lpg' and a 'lpg-pwm' node, even though
only one of them can be enabled at any time.

> +      compatible = "qcom,pm8916-pwm";
> +      #pwm-cells = <2>;
> +    };
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
new file mode 100644
index 000000000000..10aee61a7ffc
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml
@@ -0,0 +1,164 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-qcom-lpg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Light Pulse Generator
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: >
+  The Qualcomm Light Pulse Generator consists of three different hardware blocks;
+  a ramp generator with lookup table, the light pulse generator and a three
+  channel current sink. These blocks are found in a wide range of Qualcomm PMICs.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8150b-lpg
+      - qcom,pm8150l-lpg
+      - qcom,pm8916-pwm
+      - qcom,pm8941-lpg
+      - qcom,pm8994-lpg
+      - qcom,pmc8180c-lpg
+      - qcom,pmi8994-lpg
+      - qcom,pmi8998-lpg
+
+  "#pwm-cells":
+    const: 2
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  qcom,power-source:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      power-source used to drive the output, as defined in the datasheet.
+      Should be specified if the TRILED block is present
+    enum: [0, 1, 3]
+
+  qcom,dtest:
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    description: >
+      A list of integer pairs, where each pair represent the dtest line the
+      particular channel should be connected to and the flags denoting how the
+      value should be outputed, as defined in the datasheet. The number of
+      pairs should be the same as the number of channels.
+    items:
+      items:
+        - description: dtest line to attach
+        - description: flags for the attachment
+
+  multi-led:
+    type: object
+    $ref: leds-class-multicolor.yaml#
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      "^led@[0-9a-f]$":
+        type: object
+        $ref: common.yaml#
+
+patternProperties:
+  "^led@[0-9a-f]$":
+    type: object
+    $ref: common.yaml#
+
+    properties:
+      reg: true
+
+    required:
+      - reg
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    lpg {
+      compatible = "qcom,pmi8994-lpg";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      qcom,power-source = <1>;
+
+      qcom,dtest = <0 0>,
+                   <0 0>,
+                   <0 0>,
+                   <4 1>;
+
+      led@1 {
+        reg = <1>;
+        label = "green:user1";
+      };
+
+      led@2 {
+        reg = <2>;
+        label = "green:user0";
+        default-state = "on";
+      };
+
+      led@3 {
+        reg = <3>;
+        label = "green:user2";
+      };
+
+      led@4 {
+        reg = <4>;
+        label = "green:user3";
+      };
+    };
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    lpg {
+      compatible = "qcom,pmi8994-lpg";
+
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      qcom,power-source = <1>;
+
+      multi-led {
+        color = <LED_COLOR_ID_RGB>;
+        function = LED_FUNCTION_STATUS;
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        led@1 {
+          reg = <1>;
+          color = <LED_COLOR_ID_RED>;
+        };
+
+        led@2 {
+          reg = <2>;
+          color = <LED_COLOR_ID_GREEN>;
+        };
+
+        led@3 {
+          reg = <3>;
+          color = <LED_COLOR_ID_BLUE>;
+        };
+      };
+    };
+  - |
+    lpg {
+      compatible = "qcom,pm8916-pwm";
+      #pwm-cells = <2>;
+    };
+...