| Message ID | 20210719071821.31583-3-qiangqing.zhang@nxp.com |
|---|---|
| State | New |
| Headers | show |
| Series | dt-bindings: net: dwmac-imx: convert | expand |
On Mon, Jul 19, 2021 at 03:18:20PM +0800, Joakim Zhang wrote: > In order to automate the verification of DT nodes covert imx-dwmac to > nxp,dwmac-imx.yaml, and pass below checking. > > $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> > --- > .../devicetree/bindings/net/imx-dwmac.txt | 56 ----------- > .../bindings/net/nxp,dwmac-imx.yaml | 93 +++++++++++++++++++ > 2 files changed, 93 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/net/imx-dwmac.txt > create mode 100644 Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt b/Documentation/devicetree/bindings/net/imx-dwmac.txt > deleted file mode 100644 > index 921d522fe8d7..000000000000 > --- a/Documentation/devicetree/bindings/net/imx-dwmac.txt > +++ /dev/null > @@ -1,56 +0,0 @@ > -IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a IP. > - > -This file documents platform glue layer for IMX. > -Please see stmmac.txt for the other unchanged properties. > - > -The device node has following properties. > - > -Required properties: > -- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer > - and "snps,dwmac-5.10a" to select IP version. > -- clocks: Must contain a phandle for each entry in clock-names. > -- clock-names: Should be "stmmaceth" for the host clock. > - Should be "pclk" for the MAC apb clock. > - Should be "ptp_ref" for the MAC timer clock. > - Should be "tx" for the MAC RGMII TX clock: > - Should be "mem" for EQOS MEM clock. > - - "mem" clock is required for imx8dxl platform. > - - "mem" clock is not required for imx8mp platform. > -- interrupt-names: Should contain a list of interrupt names corresponding to > - the interrupts in the interrupts property, if available. > - Should be "macirq" for the main MAC IRQ > - Should be "eth_wake_irq" for the IT which wake up system > -- intf_mode: Should be phandle/offset pair. The phandle to the syscon node which > - encompases the GPR register, and the offset of the GPR register. > - - required for imx8mp platform. > - - is optional for imx8dxl platform. > - > -Optional properties: > -- intf_mode: is optional for imx8dxl platform. > -- snps,rmii_refclk_ext: to select RMII reference clock from external. > - > -Example: > - eqos: ethernet@30bf0000 { > - compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; > - reg = <0x30bf0000 0x10000>; > - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, > - <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; > - interrupt-names = "eth_wake_irq", "macirq"; > - clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, > - <&clk IMX8MP_CLK_QOS_ENET_ROOT>, > - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > - <&clk IMX8MP_CLK_ENET_QOS>; > - clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; > - assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, > - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > - <&clk IMX8MP_CLK_ENET_QOS>; > - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, > - <&clk IMX8MP_SYS_PLL2_100M>, > - <&clk IMX8MP_SYS_PLL2_125M>; > - assigned-clock-rates = <0>, <100000000>, <125000000>; > - nvmem-cells = <ð_mac0>; > - nvmem-cell-names = "mac-address"; > - nvmem_macaddr_swap; > - intf_mode = <&gpr 0x4>; > - status = "disabled"; > - }; > diff --git a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > new file mode 100644 > index 000000000000..5629b2e4ccf8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > @@ -0,0 +1,93 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: NXP i.MX8 DWMAC glue layer Device Tree Bindings > + > +maintainers: > + - Joakim Zhang <qiangqing.zhang@nxp.com> > + > +# We need a select here so we don't match all nodes with 'snps,dwmac' > +select: > + properties: > + compatible: > + contains: > + enum: > + - nxp,imx8mp-dwmac-eqos > + - nxp,imx8dxl-dwmac-eqos > + required: > + - compatible > + > +allOf: > + - $ref: "snps,dwmac.yaml#" > + > +properties: > + compatible: > + oneOf: > + - items: Don't need 'oneOf' as there is only one entry. > + - enum: > + - nxp,imx8mp-dwmac-eqos > + - nxp,imx8dxl-dwmac-eqos > + - const: snps,dwmac-5.10a > + > + clocks: > + minItems: 3 > + maxItems: 5 > + items: > + - description: MAC host clock > + - description: MAC apb clock > + - description: MAC timer clock > + - description: MAC RGMII TX clock > + - description: EQOS MEM clock > + > + clock-names: > + minItems: 3 > + maxItems: 5 > + contains: s/contains/items/ But really, like the other one, can't you define the order? > + enum: > + - stmmaceth > + - pclk > + - ptp_ref > + - tx > + - mem > + > + intf_mode: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + description: > + Should be phandle/offset pair. The phandle to the syscon node which > + encompases the GPR register, and the offset of the GPR register. Sounds like 2 cells: maxItems: 2 > + > + snps,rmii_refclk_ext: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + To select RMII reference clock from external. > + > +required: > + - compatible > + - clocks > + - clock-names > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/clock/imx8mp-clock.h> > + > + eqos: ethernet@30bf0000 { > + compatible = "nxp,imx8mp-dwmac-eqos","snps,dwmac-5.10a"; > + reg = <0x30bf0000 0x10000>; > + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "macirq", "eth_wake_irq"; > + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, > + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, > + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > + <&clk IMX8MP_CLK_ENET_QOS>; > + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; > + phy-mode = "rgmii"; > + status = "disabled"; Why are you disabling your example? Drop. > + }; > -- > 2.17.1 > >
> -----Original Message----- > From: Rob Herring <robh@kernel.org> > Sent: 2021年7月22日 0:53 > To: Joakim Zhang <qiangqing.zhang@nxp.com> > Cc: davem@davemloft.net; kuba@kernel.org; shawnguo@kernel.org; > s.hauer@pengutronix.de; festevam@gmail.com; kernel@pengutronix.de; > dl-linux-imx <linux-imx@nxp.com>; peppe.cavallaro@st.com; > joabreu@synopsys.com; netdev@vger.kernel.org; devicetree@vger.kernel.org; > linux-arm-kernel@lists.infradead.org; linux-kernel@vger.kernel.org > Subject: Re: [PATCH net-next V1 2/3] dt-bindings: net: imx-dwmac: convert > imx-dwmac bindings to yaml > > On Mon, Jul 19, 2021 at 03:18:20PM +0800, Joakim Zhang wrote: > > In order to automate the verification of DT nodes covert imx-dwmac to > > nxp,dwmac-imx.yaml, and pass below checking. > > > > $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check > > > DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.y > a > > ml $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check > > > DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.y > a > > ml > > > > Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> > > --- > > .../devicetree/bindings/net/imx-dwmac.txt | 56 ----------- > > .../bindings/net/nxp,dwmac-imx.yaml | 93 > +++++++++++++++++++ > > 2 files changed, 93 insertions(+), 56 deletions(-) delete mode > > 100644 Documentation/devicetree/bindings/net/imx-dwmac.txt > > create mode 100644 > > Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > > > diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt > > b/Documentation/devicetree/bindings/net/imx-dwmac.txt > > deleted file mode 100644 > > index 921d522fe8d7..000000000000 > > --- a/Documentation/devicetree/bindings/net/imx-dwmac.txt > > +++ /dev/null > > @@ -1,56 +0,0 @@ > > -IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a > IP. > > - > > -This file documents platform glue layer for IMX. > > -Please see stmmac.txt for the other unchanged properties. > > - > > -The device node has following properties. > > - > > -Required properties: > > -- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer > > - and "snps,dwmac-5.10a" to select IP version. > > -- clocks: Must contain a phandle for each entry in clock-names. > > -- clock-names: Should be "stmmaceth" for the host clock. > > - Should be "pclk" for the MAC apb clock. > > - Should be "ptp_ref" for the MAC timer clock. > > - Should be "tx" for the MAC RGMII TX clock: > > - Should be "mem" for EQOS MEM clock. > > - - "mem" clock is required for imx8dxl platform. > > - - "mem" clock is not required for imx8mp platform. > > -- interrupt-names: Should contain a list of interrupt names corresponding to > > - the interrupts in the interrupts property, if available. > > - Should be "macirq" for the main MAC IRQ > > - Should be "eth_wake_irq" for the IT which wake up system > > -- intf_mode: Should be phandle/offset pair. The phandle to the syscon node > which > > - encompases the GPR register, and the offset of the GPR register. > > - - required for imx8mp platform. > > - - is optional for imx8dxl platform. > > - > > -Optional properties: > > -- intf_mode: is optional for imx8dxl platform. > > -- snps,rmii_refclk_ext: to select RMII reference clock from external. > > - > > -Example: > > - eqos: ethernet@30bf0000 { > > - compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; > > - reg = <0x30bf0000 0x10000>; > > - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, > > - <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; > > - interrupt-names = "eth_wake_irq", "macirq"; > > - clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, > > - <&clk IMX8MP_CLK_QOS_ENET_ROOT>, > > - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > > - <&clk IMX8MP_CLK_ENET_QOS>; > > - clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; > > - assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, > > - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > > - <&clk IMX8MP_CLK_ENET_QOS>; > > - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, > > - <&clk IMX8MP_SYS_PLL2_100M>, > > - <&clk IMX8MP_SYS_PLL2_125M>; > > - assigned-clock-rates = <0>, <100000000>, <125000000>; > > - nvmem-cells = <ð_mac0>; > > - nvmem-cell-names = "mac-address"; > > - nvmem_macaddr_swap; > > - intf_mode = <&gpr 0x4>; > > - status = "disabled"; > > - }; > > diff --git a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > new file mode 100644 > > index 000000000000..5629b2e4ccf8 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml > > @@ -0,0 +1,93 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 > > +--- > > +$id: > > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi > > > +cetree.org%2Fschemas%2Fnet%2Fnxp%2Cdwmac-imx.yaml%23&data=0 > 4%7C01 > > > +%7Cqiangqing.zhang%40nxp.com%7Ce67c2543a57a49a20fa708d94c6802bc > %7C686 > > > +ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637624831874124189%7C > Unknown% > > > +7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haW > wiLCJ > > > +XVCI6Mn0%3D%7C1000&sdata=c0oEjThQAMvIOJYp4epHkPJr2rYMJQUb > D1mccQvs > > +mCo%3D&reserved=0 > > +$schema: > > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi > > > +cetree.org%2Fmeta-schemas%2Fcore.yaml%23&data=04%7C01%7Cqia > ngqing > > > +.zhang%40nxp.com%7Ce67c2543a57a49a20fa708d94c6802bc%7C686ea1d3b > c2b4c6 > > > +fa92cd99c5c301635%7C0%7C0%7C637624831874134148%7CUnknown%7CT > WFpbGZsb3 > > > +d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0 > %3D% > > > +7C1000&sdata=1%2BNhcSiOujYzvNsGnYLwo6PGFHGb3gacVOntovlmGes > %3D& > > +;reserved=0 > > + > > +title: NXP i.MX8 DWMAC glue layer Device Tree Bindings > > + > > +maintainers: > > + - Joakim Zhang <qiangqing.zhang@nxp.com> > > + > > +# We need a select here so we don't match all nodes with 'snps,dwmac' > > +select: > > + properties: > > + compatible: > > + contains: > > + enum: > > + - nxp,imx8mp-dwmac-eqos > > + - nxp,imx8dxl-dwmac-eqos > > + required: > > + - compatible > > + > > +allOf: > > + - $ref: "snps,dwmac.yaml#" > > + > > +properties: > > + compatible: > > + oneOf: > > + - items: > > Don't need 'oneOf' as there is only one entry. OK > > + - enum: > > + - nxp,imx8mp-dwmac-eqos > > + - nxp,imx8dxl-dwmac-eqos > > + - const: snps,dwmac-5.10a > > + > > + clocks: > > + minItems: 3 > > + maxItems: 5 > > + items: > > + - description: MAC host clock > > + - description: MAC apb clock > > + - description: MAC timer clock > > + - description: MAC RGMII TX clock > > + - description: EQOS MEM clock > > + > > + clock-names: > > + minItems: 3 > > + maxItems: 5 > > + contains: > > s/contains/items/ > > But really, like the other one, can't you define the order? OK > > + enum: > > + - stmmaceth > > + - pclk > > + - ptp_ref > > + - tx > > + - mem > > + > > + intf_mode: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: > > + Should be phandle/offset pair. The phandle to the syscon node which > > + encompases the GPR register, and the offset of the GPR register. > > Sounds like 2 cells: > > maxItems: 2 Why? I think it's only one item like below: intf_mode = <&gpr 0x4>; > > + > > + snps,rmii_refclk_ext: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + To select RMII reference clock from external. > > + > > +required: > > + - compatible > > + - clocks > > + - clock-names > > + > > +unevaluatedProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/interrupt-controller/irq.h> > > + #include <dt-bindings/clock/imx8mp-clock.h> > > + > > + eqos: ethernet@30bf0000 { > > + compatible = > "nxp,imx8mp-dwmac-eqos","snps,dwmac-5.10a"; > > + reg = <0x30bf0000 0x10000>; > > + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "macirq", "eth_wake_irq"; > > + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, > > + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, > > + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, > > + <&clk IMX8MP_CLK_ENET_QOS>; > > + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; > > + phy-mode = "rgmii"; > > + status = "disabled"; > > Why are you disabling your example? Drop. OK Will send a follow-up patch to improve this dt-binding later. Best Regards, Joakim Zhang > > > + }; > > -- > > 2.17.1 > > > >
diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt b/Documentation/devicetree/bindings/net/imx-dwmac.txt deleted file mode 100644 index 921d522fe8d7..000000000000 --- a/Documentation/devicetree/bindings/net/imx-dwmac.txt +++ /dev/null @@ -1,56 +0,0 @@ -IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a IP. - -This file documents platform glue layer for IMX. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer - and "snps,dwmac-5.10a" to select IP version. -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: Should be "stmmaceth" for the host clock. - Should be "pclk" for the MAC apb clock. - Should be "ptp_ref" for the MAC timer clock. - Should be "tx" for the MAC RGMII TX clock: - Should be "mem" for EQOS MEM clock. - - "mem" clock is required for imx8dxl platform. - - "mem" clock is not required for imx8mp platform. -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ - Should be "eth_wake_irq" for the IT which wake up system -- intf_mode: Should be phandle/offset pair. The phandle to the syscon node which - encompases the GPR register, and the offset of the GPR register. - - required for imx8mp platform. - - is optional for imx8dxl platform. - -Optional properties: -- intf_mode: is optional for imx8dxl platform. -- snps,rmii_refclk_ext: to select RMII reference clock from external. - -Example: - eqos: ethernet@30bf0000 { - compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; - reg = <0x30bf0000 0x10000>; - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "eth_wake_irq", "macirq"; - clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, - <&clk IMX8MP_CLK_QOS_ENET_ROOT>, - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, - <&clk IMX8MP_CLK_ENET_QOS>; - clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; - assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, - <&clk IMX8MP_CLK_ENET_QOS>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, - <&clk IMX8MP_SYS_PLL2_100M>, - <&clk IMX8MP_SYS_PLL2_125M>; - assigned-clock-rates = <0>, <100000000>, <125000000>; - nvmem-cells = <ð_mac0>; - nvmem-cell-names = "mac-address"; - nvmem_macaddr_swap; - intf_mode = <&gpr 0x4>; - status = "disabled"; - }; diff --git a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml new file mode 100644 index 000000000000..5629b2e4ccf8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8 DWMAC glue layer Device Tree Bindings + +maintainers: + - Joakim Zhang <qiangqing.zhang@nxp.com> + +# We need a select here so we don't match all nodes with 'snps,dwmac' +select: + properties: + compatible: + contains: + enum: + - nxp,imx8mp-dwmac-eqos + - nxp,imx8dxl-dwmac-eqos + required: + - compatible + +allOf: + - $ref: "snps,dwmac.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - nxp,imx8mp-dwmac-eqos + - nxp,imx8dxl-dwmac-eqos + - const: snps,dwmac-5.10a + + clocks: + minItems: 3 + maxItems: 5 + items: + - description: MAC host clock + - description: MAC apb clock + - description: MAC timer clock + - description: MAC RGMII TX clock + - description: EQOS MEM clock + + clock-names: + minItems: 3 + maxItems: 5 + contains: + enum: + - stmmaceth + - pclk + - ptp_ref + - tx + - mem + + intf_mode: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should be phandle/offset pair. The phandle to the syscon node which + encompases the GPR register, and the offset of the GPR register. + + snps,rmii_refclk_ext: + $ref: /schemas/types.yaml#/definitions/flag + description: + To select RMII reference clock from external. + +required: + - compatible + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/imx8mp-clock.h> + + eqos: ethernet@30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos","snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + phy-mode = "rgmii"; + status = "disabled"; + };
In order to automate the verification of DT nodes covert imx-dwmac to nxp,dwmac-imx.yaml, and pass below checking. $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> --- .../devicetree/bindings/net/imx-dwmac.txt | 56 ----------- .../bindings/net/nxp,dwmac-imx.yaml | 93 +++++++++++++++++++ 2 files changed, 93 insertions(+), 56 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/imx-dwmac.txt create mode 100644 Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml