| Message ID | 20220316131000.9874-14-gabriel.fernandez@foss.st.com |
|---|---|
| State | New |
| Headers | show |
| Series | Introduction of STM32MP13 RCC driver (Reset Clock Controller) | expand |
On 3/16/22 14:10, gabriel.fernandez@foss.st.com wrote: > From: Gabriel Fernandez <gabriel.fernandez@foss.st.com> > > Enables Reset and Clocks Controller on STM32MP13 > > Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com> > --- > arch/arm/boot/dts/stm32mp131.dtsi | 107 +++++++++++------------------ > arch/arm/boot/dts/stm32mp133.dtsi | 4 +- > arch/arm/boot/dts/stm32mp13xf.dtsi | 3 +- > 3 files changed, 46 insertions(+), 68 deletions(-) > > diff --git a/arch/arm/boot/dts/stm32mp131.dtsi b/arch/arm/boot/dts/stm32mp131.dtsi > index 78eac53224d4..d7300b00ec19 100644 > --- a/arch/arm/boot/dts/stm32mp131.dtsi > +++ b/arch/arm/boot/dts/stm32mp131.dtsi > @@ -4,6 +4,8 @@ > * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics. > */ > #include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/clock/stm32mp13-clks.h> > +#include <dt-bindings/reset/stm32mp13-resets.h> > > / { > #address-cells = <1>; > @@ -64,54 +66,8 @@ scmi_reset: protocol@16 { > }; > }; > }; > - clocks { > - clk_axi: clk-axi { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <266500000>; > - }; > - > - clk_hse: clk-hse { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <24000000>; > - }; > - > - clk_hsi: clk-hsi { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <64000000>; > - }; > - > - clk_lsi: clk-lsi { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <32000>; > - }; > - > - clk_pclk3: clk-pclk3 { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <104438965>; > - }; > > - clk_pclk4: clk-pclk4 { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <133250000>; > - }; > - > - clk_pll4_p: clk-pll4_p { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <50000000>; > - }; > - > - clk_pll4_r: clk-pll4_r { > - #clock-cells = <0>; > - compatible = "fixed-clock"; > - clock-frequency = <99000000>; > - }; > + clocks { > }; > > intc: interrupt-controller@a0021000 { > @@ -148,7 +104,8 @@ uart4: serial@40010000 { > compatible = "st,stm32h7-uart"; > reg = <0x40010000 0x400>; > interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clk_hsi>; > + clocks = <&rcc UART4_K>; > + resets = <&rcc UART4_R>; > status = "disabled"; > }; > > @@ -163,7 +120,8 @@ dma1: dma-controller@48000000 { > <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc DMA1>; > + resets = <&rcc DMA1_R>; > #dma-cells = <4>; > st,mem2mem; > dma-requests = <8>; > @@ -180,7 +138,8 @@ dma2: dma-controller@48001000 { > <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc DMA2>; > + resets = <&rcc DMA2_R>; > #dma-cells = <4>; > st,mem2mem; > dma-requests = <8>; > @@ -189,13 +148,29 @@ dma2: dma-controller@48001000 { > dmamux1: dma-router@48002000 { > compatible = "st,stm32h7-dmamux"; > reg = <0x48002000 0x40>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc DMAMUX1>; > + resets = <&rcc DMAMUX1_R>; > #dma-cells = <3>; > dma-masters = <&dma1 &dma2>; > dma-requests = <128>; > dma-channels = <16>; > }; > > + rcc: rcc@50000000 { > + compatible = "st,stm32mp13-rcc", "syscon"; > + reg = <0x50000000 0x1000>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + > + clock-names = "hse", "hsi", "csi", "lse", "lsi"; > + It doesn't match with current yaml description. I'm preparing a patch to update rcc yaml file. You will have to check that it matches with this node. > + clocks = <&scmi_clk CK_SCMI_HSE>, > + <&scmi_clk CK_SCMI_HSI>, > + <&scmi_clk CK_SCMI_CSI>, > + <&scmi_clk CK_SCMI_LSE>, > + <&scmi_clk CK_SCMI_LSI>; > + }; > + > exti: interrupt-controller@5000d000 { > compatible = "st,stm32mp13-exti", "syscon"; > interrupt-controller; > @@ -206,14 +181,14 @@ exti: interrupt-controller@5000d000 { > syscfg: syscon@50020000 { > compatible = "st,stm32mp157-syscfg", "syscon"; > reg = <0x50020000 0x400>; > - clocks = <&clk_pclk3>; > + clocks = <&rcc SYSCFG>; > }; > > mdma: dma-controller@58000000 { > compatible = "st,stm32h7-mdma"; > reg = <0x58000000 0x1000>; > interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc MDMA>; > #dma-cells = <5>; > dma-channels = <32>; > dma-requests = <48>; > @@ -225,8 +200,9 @@ sdmmc1: mmc@58005000 { > reg = <0x58005000 0x1000>, <0x58006000 0x1000>; > interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; > interrupt-names = "cmd_irq"; > - clocks = <&clk_pll4_p>; > + clocks = <&rcc SDMMC1_K>; > clock-names = "apb_pclk"; > + resets = <&rcc SDMMC1_R>; > cap-sd-highspeed; > cap-mmc-highspeed; > max-frequency = <130000000>; > @@ -239,8 +215,9 @@ sdmmc2: mmc@58007000 { > reg = <0x58007000 0x1000>, <0x58008000 0x1000>; > interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; > interrupt-names = "cmd_irq"; > - clocks = <&clk_pll4_p>; > + clocks = <&rcc SDMMC2_K>; > clock-names = "apb_pclk"; > + resets = <&rcc SDMMC2_R>; > cap-sd-highspeed; > cap-mmc-highspeed; > max-frequency = <130000000>; > @@ -250,7 +227,7 @@ sdmmc2: mmc@58007000 { > iwdg2: watchdog@5a002000 { > compatible = "st,stm32mp1-iwdg"; > reg = <0x5a002000 0x400>; > - clocks = <&clk_pclk4>, <&clk_lsi>; > + clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>; > clock-names = "pclk", "lsi"; > status = "disabled"; > }; > @@ -289,7 +266,7 @@ gpioa: gpio@50002000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x0 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOA>; > st,bank-name = "GPIOA"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 0 16>; > @@ -301,7 +278,7 @@ gpiob: gpio@50003000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x1000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOB>; > st,bank-name = "GPIOB"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 16 16>; > @@ -313,7 +290,7 @@ gpioc: gpio@50004000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x2000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOC>; > st,bank-name = "GPIOC"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 32 16>; > @@ -325,7 +302,7 @@ gpiod: gpio@50005000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x3000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOD>; > st,bank-name = "GPIOD"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 48 16>; > @@ -337,7 +314,7 @@ gpioe: gpio@50006000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x4000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOE>; > st,bank-name = "GPIOE"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 64 16>; > @@ -349,7 +326,7 @@ gpiof: gpio@50007000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x5000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOF>; > st,bank-name = "GPIOF"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 80 16>; > @@ -361,7 +338,7 @@ gpiog: gpio@50008000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x6000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOG>; > st,bank-name = "GPIOG"; > ngpios = <16>; > gpio-ranges = <&pinctrl 0 96 16>; > @@ -373,7 +350,7 @@ gpioh: gpio@50009000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x7000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOH>; > st,bank-name = "GPIOH"; > ngpios = <15>; > gpio-ranges = <&pinctrl 0 112 15>; > @@ -385,7 +362,7 @@ gpioi: gpio@5000a000 { > interrupt-controller; > #interrupt-cells = <2>; > reg = <0x8000 0x400>; > - clocks = <&clk_pclk4>; > + clocks = <&rcc GPIOI>; > st,bank-name = "GPIOI"; > ngpios = <8>; > gpio-ranges = <&pinctrl 0 128 8>; > diff --git a/arch/arm/boot/dts/stm32mp133.dtsi b/arch/arm/boot/dts/stm32mp133.dtsi > index 0fb1386257cf..531c263c9f46 100644 > --- a/arch/arm/boot/dts/stm32mp133.dtsi > +++ b/arch/arm/boot/dts/stm32mp133.dtsi > @@ -15,7 +15,7 @@ m_can1: can@4400e000 { > interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; > interrupt-names = "int0", "int1"; > - clocks = <&clk_hse>, <&clk_pll4_r>; > + clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>; > clock-names = "hclk", "cclk"; > bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; > status = "disabled"; > @@ -28,7 +28,7 @@ m_can2: can@4400f000 { > interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; > interrupt-names = "int0", "int1"; > - clocks = <&clk_hse>, <&clk_pll4_r>; > + clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>; > clock-names = "hclk", "cclk"; > bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; > status = "disabled"; > diff --git a/arch/arm/boot/dts/stm32mp13xf.dtsi b/arch/arm/boot/dts/stm32mp13xf.dtsi > index fa6889e30591..4d00e7592882 100644 > --- a/arch/arm/boot/dts/stm32mp13xf.dtsi > +++ b/arch/arm/boot/dts/stm32mp13xf.dtsi > @@ -10,7 +10,8 @@ cryp: crypto@54002000 { > compatible = "st,stm32mp1-cryp"; > reg = <0x54002000 0x400>; > interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; > - clocks = <&clk_axi>; > + clocks = <&rcc CRYP1>; > + resets = <&rcc CRYP1_R>; > status = "disabled"; > }; > };
diff --git a/arch/arm/boot/dts/stm32mp131.dtsi b/arch/arm/boot/dts/stm32mp131.dtsi index 78eac53224d4..d7300b00ec19 100644 --- a/arch/arm/boot/dts/stm32mp131.dtsi +++ b/arch/arm/boot/dts/stm32mp131.dtsi @@ -4,6 +4,8 @@ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics. */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/stm32mp13-clks.h> +#include <dt-bindings/reset/stm32mp13-resets.h> / { #address-cells = <1>; @@ -64,54 +66,8 @@ scmi_reset: protocol@16 { }; }; }; - clocks { - clk_axi: clk-axi { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <266500000>; - }; - - clk_hse: clk-hse { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <24000000>; - }; - - clk_hsi: clk-hsi { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <64000000>; - }; - - clk_lsi: clk-lsi { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32000>; - }; - - clk_pclk3: clk-pclk3 { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <104438965>; - }; - clk_pclk4: clk-pclk4 { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <133250000>; - }; - - clk_pll4_p: clk-pll4_p { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <50000000>; - }; - - clk_pll4_r: clk-pll4_r { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <99000000>; - }; + clocks { }; intc: interrupt-controller@a0021000 { @@ -148,7 +104,8 @@ uart4: serial@40010000 { compatible = "st,stm32h7-uart"; reg = <0x40010000 0x400>; interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_hsi>; + clocks = <&rcc UART4_K>; + resets = <&rcc UART4_R>; status = "disabled"; }; @@ -163,7 +120,8 @@ dma1: dma-controller@48000000 { <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_pclk4>; + clocks = <&rcc DMA1>; + resets = <&rcc DMA1_R>; #dma-cells = <4>; st,mem2mem; dma-requests = <8>; @@ -180,7 +138,8 @@ dma2: dma-controller@48001000 { <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_pclk4>; + clocks = <&rcc DMA2>; + resets = <&rcc DMA2_R>; #dma-cells = <4>; st,mem2mem; dma-requests = <8>; @@ -189,13 +148,29 @@ dma2: dma-controller@48001000 { dmamux1: dma-router@48002000 { compatible = "st,stm32h7-dmamux"; reg = <0x48002000 0x40>; - clocks = <&clk_pclk4>; + clocks = <&rcc DMAMUX1>; + resets = <&rcc DMAMUX1_R>; #dma-cells = <3>; dma-masters = <&dma1 &dma2>; dma-requests = <128>; dma-channels = <16>; }; + rcc: rcc@50000000 { + compatible = "st,stm32mp13-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + + clock-names = "hse", "hsi", "csi", "lse", "lsi"; + + clocks = <&scmi_clk CK_SCMI_HSE>, + <&scmi_clk CK_SCMI_HSI>, + <&scmi_clk CK_SCMI_CSI>, + <&scmi_clk CK_SCMI_LSE>, + <&scmi_clk CK_SCMI_LSI>; + }; + exti: interrupt-controller@5000d000 { compatible = "st,stm32mp13-exti", "syscon"; interrupt-controller; @@ -206,14 +181,14 @@ exti: interrupt-controller@5000d000 { syscfg: syscon@50020000 { compatible = "st,stm32mp157-syscfg", "syscon"; reg = <0x50020000 0x400>; - clocks = <&clk_pclk3>; + clocks = <&rcc SYSCFG>; }; mdma: dma-controller@58000000 { compatible = "st,stm32h7-mdma"; reg = <0x58000000 0x1000>; interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_pclk4>; + clocks = <&rcc MDMA>; #dma-cells = <5>; dma-channels = <32>; dma-requests = <48>; @@ -225,8 +200,9 @@ sdmmc1: mmc@58005000 { reg = <0x58005000 0x1000>, <0x58006000 0x1000>; interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "cmd_irq"; - clocks = <&clk_pll4_p>; + clocks = <&rcc SDMMC1_K>; clock-names = "apb_pclk"; + resets = <&rcc SDMMC1_R>; cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <130000000>; @@ -239,8 +215,9 @@ sdmmc2: mmc@58007000 { reg = <0x58007000 0x1000>, <0x58008000 0x1000>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "cmd_irq"; - clocks = <&clk_pll4_p>; + clocks = <&rcc SDMMC2_K>; clock-names = "apb_pclk"; + resets = <&rcc SDMMC2_R>; cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <130000000>; @@ -250,7 +227,7 @@ sdmmc2: mmc@58007000 { iwdg2: watchdog@5a002000 { compatible = "st,stm32mp1-iwdg"; reg = <0x5a002000 0x400>; - clocks = <&clk_pclk4>, <&clk_lsi>; + clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>; clock-names = "pclk", "lsi"; status = "disabled"; }; @@ -289,7 +266,7 @@ gpioa: gpio@50002000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x0 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOA>; st,bank-name = "GPIOA"; ngpios = <16>; gpio-ranges = <&pinctrl 0 0 16>; @@ -301,7 +278,7 @@ gpiob: gpio@50003000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x1000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOB>; st,bank-name = "GPIOB"; ngpios = <16>; gpio-ranges = <&pinctrl 0 16 16>; @@ -313,7 +290,7 @@ gpioc: gpio@50004000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x2000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOC>; st,bank-name = "GPIOC"; ngpios = <16>; gpio-ranges = <&pinctrl 0 32 16>; @@ -325,7 +302,7 @@ gpiod: gpio@50005000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x3000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOD>; st,bank-name = "GPIOD"; ngpios = <16>; gpio-ranges = <&pinctrl 0 48 16>; @@ -337,7 +314,7 @@ gpioe: gpio@50006000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x4000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOE>; st,bank-name = "GPIOE"; ngpios = <16>; gpio-ranges = <&pinctrl 0 64 16>; @@ -349,7 +326,7 @@ gpiof: gpio@50007000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x5000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOF>; st,bank-name = "GPIOF"; ngpios = <16>; gpio-ranges = <&pinctrl 0 80 16>; @@ -361,7 +338,7 @@ gpiog: gpio@50008000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x6000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOG>; st,bank-name = "GPIOG"; ngpios = <16>; gpio-ranges = <&pinctrl 0 96 16>; @@ -373,7 +350,7 @@ gpioh: gpio@50009000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x7000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOH>; st,bank-name = "GPIOH"; ngpios = <15>; gpio-ranges = <&pinctrl 0 112 15>; @@ -385,7 +362,7 @@ gpioi: gpio@5000a000 { interrupt-controller; #interrupt-cells = <2>; reg = <0x8000 0x400>; - clocks = <&clk_pclk4>; + clocks = <&rcc GPIOI>; st,bank-name = "GPIOI"; ngpios = <8>; gpio-ranges = <&pinctrl 0 128 8>; diff --git a/arch/arm/boot/dts/stm32mp133.dtsi b/arch/arm/boot/dts/stm32mp133.dtsi index 0fb1386257cf..531c263c9f46 100644 --- a/arch/arm/boot/dts/stm32mp133.dtsi +++ b/arch/arm/boot/dts/stm32mp133.dtsi @@ -15,7 +15,7 @@ m_can1: can@4400e000 { interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "int0", "int1"; - clocks = <&clk_hse>, <&clk_pll4_r>; + clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>; clock-names = "hclk", "cclk"; bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; status = "disabled"; @@ -28,7 +28,7 @@ m_can2: can@4400f000 { interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "int0", "int1"; - clocks = <&clk_hse>, <&clk_pll4_r>; + clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>; clock-names = "hclk", "cclk"; bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; status = "disabled"; diff --git a/arch/arm/boot/dts/stm32mp13xf.dtsi b/arch/arm/boot/dts/stm32mp13xf.dtsi index fa6889e30591..4d00e7592882 100644 --- a/arch/arm/boot/dts/stm32mp13xf.dtsi +++ b/arch/arm/boot/dts/stm32mp13xf.dtsi @@ -10,7 +10,8 @@ cryp: crypto@54002000 { compatible = "st,stm32mp1-cryp"; reg = <0x54002000 0x400>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk_axi>; + clocks = <&rcc CRYP1>; + resets = <&rcc CRYP1_R>; status = "disabled"; }; };