| Message ID | 20231101-th1520-mmc-v4-0-86e0216b5994@baylibre.com |
|---|---|
| Headers | show |
| Series | RISC-V: Add MMC support for TH1520 boards | expand |
On 2/11/23 04:48, Drew Fustini wrote: > Add support for the mmc controller in the T-Head TH1520 with the new > compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for > set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning. > > Signed-off-by: Drew Fustini <dfustini@baylibre.com> One question below, otherwise: Acked-by: Adrian Hunter <adrian.hunter@intel.com> > --- > drivers/mmc/host/sdhci-of-dwcmshc.c | 348 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 348 insertions(+) > > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c > index 3a3bae6948a8..1a1386b742c1 100644 > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c > @@ -8,6 +8,7 @@ > */ > > #include <linux/acpi.h> > +#include <linux/bitfield.h> > #include <linux/clk.h> > #include <linux/dma-mapping.h> > #include <linux/iopoll.h> > @@ -35,6 +36,21 @@ > #define DWCMSHC_CARD_IS_EMMC BIT(0) > #define DWCMSHC_ENHANCED_STROBE BIT(8) > #define DWCMSHC_EMMC_ATCTRL 0x40 > +/* Tuning and auto-tuning fields in AT_CTRL_R control register */ > +#define AT_CTRL_AT_EN BIT(0) /* autotuning is enabled */ > +#define AT_CTRL_CI_SEL BIT(1) /* interval to drive center phase select */ > +#define AT_CTRL_SWIN_TH_EN BIT(2) /* sampling window threshold enable */ > +#define AT_CTRL_RPT_TUNE_ERR BIT(3) /* enable reporting framing errors */ > +#define AT_CTRL_SW_TUNE_EN BIT(4) /* enable software managed tuning */ > +#define AT_CTRL_WIN_EDGE_SEL_MASK GENMASK(11, 8) /* bits [11:8] */ > +#define AT_CTRL_WIN_EDGE_SEL 0xf /* sampling window edge select */ > +#define AT_CTRL_TUNE_CLK_STOP_EN BIT(16) /* clocks stopped during phase code change */ > +#define AT_CTRL_PRE_CHANGE_DLY_MASK GENMASK(18, 17) /* bits [18:17] */ > +#define AT_CTRL_PRE_CHANGE_DLY 0x1 /* 2-cycle latency */ > +#define AT_CTRL_POST_CHANGE_DLY_MASK GENMASK(20, 19) /* bits [20:19] */ > +#define AT_CTRL_POST_CHANGE_DLY 0x3 /* 4-cycle latency */ > +#define AT_CTRL_SWIN_TH_VAL_MASK GENMASK(31, 24) /* bits [31:24] */ > +#define AT_CTRL_SWIN_TH_VAL 0x9 /* sampling window threshold */ > > /* Rockchip specific Registers */ > #define DWCMSHC_EMMC_DLL_CTRL 0x800 > @@ -72,6 +88,82 @@ > (((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0)) > #define RK35xx_MAX_CLKS 3 > > +/* PHY register area pointer */ > +#define DWC_MSHC_PTR_PHY_R 0x300 > + > +/* PHY general configuration */ > +#define PHY_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x00) > +#define PHY_CNFG_RSTN_DEASSERT 0x1 /* Deassert PHY reset */ > +#define PHY_CNFG_PAD_SP_MASK GENMASK(19, 16) /* bits [19:16] */ > +#define PHY_CNFG_PAD_SP 0x0c /* PMOS TX drive strength */ > +#define PHY_CNFG_PAD_SN_MASK GENMASK(23, 20) /* bits [23:20] */ > +#define PHY_CNFG_PAD_SN 0x0c /* NMOS TX drive strength */ > + > +/* PHY command/response pad settings */ > +#define PHY_CMDPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x04) > + > +/* PHY data pad settings */ > +#define PHY_DATAPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x06) > + > +/* PHY clock pad settings */ > +#define PHY_CLKPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x08) > + > +/* PHY strobe pad settings */ > +#define PHY_STBPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0a) > + > +/* PHY reset pad settings */ > +#define PHY_RSTNPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0c) > + > +/* Bitfields are common for all pad settings */ > +#define PHY_PAD_RXSEL_1V8 0x1 /* Receiver type select for 1.8V */ > +#define PHY_PAD_RXSEL_3V3 0x2 /* Receiver type select for 3.3V */ > + > +#define PHY_PAD_WEAKPULL_MASK GENMASK(4, 3) /* bits [4:3] */ > +#define PHY_PAD_WEAKPULL_PULLUP 0x1 /* Weak pull up enabled */ > +#define PHY_PAD_WEAKPULL_PULLDOWN 0x2 /* Weak pull down enabled */ > + > +#define PHY_PAD_TXSLEW_CTRL_P_MASK GENMASK(8, 5) /* bits [8:5] */ > +#define PHY_PAD_TXSLEW_CTRL_P 0x3 /* Slew control for P-Type pad TX */ > +#define PHY_PAD_TXSLEW_CTRL_N_MASK GENMASK(12, 9) /* bits [12:9] */ > +#define PHY_PAD_TXSLEW_CTRL_N 0x3 /* Slew control for N-Type pad TX */ > + > +/* PHY CLK delay line settings */ > +#define PHY_SDCLKDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x1d) > +#define PHY_SDCLKDL_CNFG_UPDATE BIT(4) /* set before writing to SDCLKDL_DC */ > + > +/* PHY CLK delay line delay code */ > +#define PHY_SDCLKDL_DC_R (DWC_MSHC_PTR_PHY_R + 0x1e) > +#define PHY_SDCLKDL_DC_INITIAL 0x40 /* initial delay code */ > +#define PHY_SDCLKDL_DC_DEFAULT 0x32 /* default delay code */ > +#define PHY_SDCLKDL_DC_HS400 0x18 /* delay code for HS400 mode */ > + > +/* PHY drift_cclk_rx delay line configuration setting */ > +#define PHY_ATDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x21) > +#define PHY_ATDL_CNFG_INPSEL_MASK GENMASK(3, 2) /* bits [3:2] */ > +#define PHY_ATDL_CNFG_INPSEL 0x3 /* delay line input source */ > + > +/* PHY DLL control settings */ > +#define PHY_DLL_CTRL_R (DWC_MSHC_PTR_PHY_R + 0x24) > +#define PHY_DLL_CTRL_DISABLE 0x0 /* PHY DLL is enabled */ > +#define PHY_DLL_CTRL_ENABLE 0x1 /* PHY DLL is disabled */ > + > +/* PHY DLL configuration register 1 */ > +#define PHY_DLL_CNFG1_R (DWC_MSHC_PTR_PHY_R + 0x25) > +#define PHY_DLL_CNFG1_SLVDLY_MASK GENMASK(5, 4) /* bits [5:4] */ > +#define PHY_DLL_CNFG1_SLVDLY 0x2 /* DLL slave update delay input */ > +#define PHY_DLL_CNFG1_WAITCYCLE 0x5 /* DLL wait cycle input */ > + > +/* PHY DLL configuration register 2 */ > +#define PHY_DLL_CNFG2_R (DWC_MSHC_PTR_PHY_R + 0x26) > +#define PHY_DLL_CNFG2_JUMPSTEP 0xa /* DLL jump step input */ > + > +/* PHY DLL master and slave delay line configuration settings */ > +#define PHY_DLLDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x28) > +#define PHY_DLLDL_CNFG_SLV_INPSEL_MASK GENMASK(6, 5) /* bits [6:5] */ > +#define PHY_DLLDL_CNFG_SLV_INPSEL 0x3 /* clock source select for slave DL */ > + > +#define FLAG_IO_FIXED_1V8 BIT(0) > + > #define BOUNDARY_OK(addr, len) \ > ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1))) > > @@ -92,6 +184,8 @@ struct dwcmshc_priv { > struct clk *bus_clk; > int vendor_specific_area1; /* P_VENDOR_SPECIFIC_AREA reg */ > void *priv; /* pointer to SoC private stuff */ > + u16 delay_line; > + u16 flags; > }; > > /* > @@ -157,6 +251,126 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq) > sdhci_request(mmc, mrq); > } > > +static void dwcmshc_phy_1_8v_init(struct sdhci_host *host) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + u32 val; > + > + /* deassert phy reset & set tx drive strength */ > + val = PHY_CNFG_RSTN_DEASSERT; > + val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP); > + val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN); > + sdhci_writel(host, val, PHY_CNFG_R); > + > + /* disable delay line */ > + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R); > + > + /* set delay line */ > + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R); > + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R); > + > + /* enable delay lane */ > + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R); > + val &= ~(PHY_SDCLKDL_CNFG_UPDATE); > + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R); > + > + /* configure phy pads */ > + val = PHY_PAD_RXSEL_1V8; > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R); > + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R); > + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R); > + > + val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R); > + > + val = PHY_PAD_RXSEL_1V8; > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_STBPAD_CNFG_R); > + > + /* enable data strobe mode */ > + sdhci_writeb(host, FIELD_PREP(PHY_DLLDL_CNFG_SLV_INPSEL_MASK, PHY_DLLDL_CNFG_SLV_INPSEL), > + PHY_DLLDL_CNFG_R); > + > + /* enable phy dll */ > + sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R); > +} > + > +static void dwcmshc_phy_3_3v_init(struct sdhci_host *host) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + u32 val; > + > + /* deassert phy reset & set tx drive strength */ > + val = PHY_CNFG_RSTN_DEASSERT; > + val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP); > + val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN); > + sdhci_writel(host, val, PHY_CNFG_R); > + > + /* disable delay line */ > + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R); > + > + /* set delay line */ > + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R); > + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R); > + > + /* enable delay lane */ > + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R); > + val &= ~(PHY_SDCLKDL_CNFG_UPDATE); > + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R); > + > + /* configure phy pads */ > + val = PHY_PAD_RXSEL_3V3; > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R); > + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R); > + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R); > + > + val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R); > + > + val = PHY_PAD_RXSEL_3V3; > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > + sdhci_writew(host, val, PHY_STBPAD_CNFG_R); > + > + /* enable phy dll */ > + sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R); > +} > + > +static void th1520_sdhci_set_phy(struct sdhci_host *host) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + u16 emmc_ctrl; > + > + /* Before power on, set PHY configs */ > + if (priv->flags & FLAG_IO_FIXED_1V8) > + dwcmshc_phy_1_8v_init(host); > + else > + dwcmshc_phy_3_3v_init(host); > + > + if (host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) { Perhaps you mean both MMC_CAP2_NO_SD and MMC_CAP2_NO_SDIO which would be as below? if ((host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) == (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) { or if (host->mmc->caps2 & MMC_CAP2_NO_SD && host->mmc->caps2 & MMC_CAP2_NO_SDIO) { or some such? > + emmc_ctrl = sdhci_readw(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL); > + emmc_ctrl |= DWCMSHC_CARD_IS_EMMC; > + sdhci_writew(host, emmc_ctrl, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL); > + } > + > + sdhci_writeb(host, FIELD_PREP(PHY_DLL_CNFG1_SLVDLY_MASK, PHY_DLL_CNFG1_SLVDLY) | > + PHY_DLL_CNFG1_WAITCYCLE, PHY_DLL_CNFG1_R); > +} > + > static void dwcmshc_set_uhs_signaling(struct sdhci_host *host, > unsigned int timing) > { > @@ -189,9 +403,25 @@ static void dwcmshc_set_uhs_signaling(struct sdhci_host *host, > ctrl_2 |= DWCMSHC_CTRL_HS400; > } > > + if (priv->flags & FLAG_IO_FIXED_1V8) > + ctrl_2 |= SDHCI_CTRL_VDD_180; > sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); > } > > +static void th1520_set_uhs_signaling(struct sdhci_host *host, > + unsigned int timing) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + > + dwcmshc_set_uhs_signaling(host, timing); > + if (timing == MMC_TIMING_MMC_HS400) > + priv->delay_line = PHY_SDCLKDL_DC_HS400; > + else > + sdhci_writeb(host, 0, PHY_DLLDL_CNFG_R); > + th1520_sdhci_set_phy(host); > +} > + > static void dwcmshc_hs400_enhanced_strobe(struct mmc_host *mmc, > struct mmc_ios *ios) > { > @@ -338,6 +568,79 @@ static void rk35xx_sdhci_reset(struct sdhci_host *host, u8 mask) > sdhci_reset(host, mask); > } > > +static int th1520_execute_tuning(struct sdhci_host *host, u32 opcode) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + u32 val = 0; > + > + if (host->flags & SDHCI_HS400_TUNING) > + return 0; > + > + sdhci_writeb(host, FIELD_PREP(PHY_ATDL_CNFG_INPSEL_MASK, PHY_ATDL_CNFG_INPSEL), > + PHY_ATDL_CNFG_R); > + val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL); > + > + /* > + * configure tuning settings: > + * - center phase select code driven in block gap interval > + * - disable reporting of framing errors > + * - disable software managed tuning > + * - disable user selection of sampling window edges, > + * instead tuning calculated edges are used > + */ > + val &= ~(AT_CTRL_CI_SEL | AT_CTRL_RPT_TUNE_ERR | AT_CTRL_SW_TUNE_EN | > + FIELD_PREP(AT_CTRL_WIN_EDGE_SEL_MASK, AT_CTRL_WIN_EDGE_SEL)); > + > + /* > + * configure tuning settings: > + * - enable auto-tuning > + * - enable sampling window threshold > + * - stop clocks during phase code change > + * - set max latency in cycles between tx and rx clocks > + * - set max latency in cycles to switch output phase > + * - set max sampling window threshold value > + */ > + val |= AT_CTRL_AT_EN | AT_CTRL_SWIN_TH_EN | AT_CTRL_TUNE_CLK_STOP_EN; > + val |= FIELD_PREP(AT_CTRL_PRE_CHANGE_DLY_MASK, AT_CTRL_PRE_CHANGE_DLY); > + val |= FIELD_PREP(AT_CTRL_POST_CHANGE_DLY_MASK, AT_CTRL_POST_CHANGE_DLY); > + val |= FIELD_PREP(AT_CTRL_SWIN_TH_VAL_MASK, AT_CTRL_SWIN_TH_VAL); > + > + sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL); > + val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL); > + > + /* perform tuning */ > + sdhci_start_tuning(host); > + host->tuning_err = __sdhci_execute_tuning(host, opcode); > + if (host->tuning_err) { > + /* disable auto-tuning upon tuning error */ > + val &= ~AT_CTRL_AT_EN; > + sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL); > + dev_err(mmc_dev(host->mmc), "tuning failed: %d\n", host->tuning_err); > + return -EIO; > + } > + sdhci_end_tuning(host); > + > + return 0; > +} > + > +static void th1520_sdhci_reset(struct sdhci_host *host, u8 mask) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > + u16 ctrl_2; > + > + sdhci_reset(host, mask); > + > + if (priv->flags & FLAG_IO_FIXED_1V8) { > + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); > + if (!(ctrl_2 & SDHCI_CTRL_VDD_180)) { > + ctrl_2 |= SDHCI_CTRL_VDD_180; > + sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); > + } > + } > +} > + > static const struct sdhci_ops sdhci_dwcmshc_ops = { > .set_clock = sdhci_set_clock, > .set_bus_width = sdhci_set_bus_width, > @@ -356,6 +659,17 @@ static const struct sdhci_ops sdhci_dwcmshc_rk35xx_ops = { > .adma_write_desc = dwcmshc_adma_write_desc, > }; > > +static const struct sdhci_ops sdhci_dwcmshc_th1520_ops = { > + .set_clock = sdhci_set_clock, > + .set_bus_width = sdhci_set_bus_width, > + .set_uhs_signaling = th1520_set_uhs_signaling, > + .get_max_clock = dwcmshc_get_max_clock, > + .reset = th1520_sdhci_reset, > + .adma_write_desc = dwcmshc_adma_write_desc, > + .voltage_switch = dwcmshc_phy_1_8v_init, > + .platform_execute_tuning = &th1520_execute_tuning, > +}; > + > static const struct sdhci_pltfm_data sdhci_dwcmshc_pdata = { > .ops = &sdhci_dwcmshc_ops, > .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, > @@ -379,6 +693,12 @@ static const struct sdhci_pltfm_data sdhci_dwcmshc_rk35xx_pdata = { > SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN, > }; > > +static const struct sdhci_pltfm_data sdhci_dwcmshc_th1520_pdata = { > + .ops = &sdhci_dwcmshc_th1520_ops, > + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN, > + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN, > +}; > + > static int dwcmshc_rk35xx_init(struct sdhci_host *host, struct dwcmshc_priv *dwc_priv) > { > int err; > @@ -447,6 +767,10 @@ static const struct of_device_id sdhci_dwcmshc_dt_ids[] = { > .compatible = "snps,dwcmshc-sdhci", > .data = &sdhci_dwcmshc_pdata, > }, > + { > + .compatible = "thead,th1520-dwcmshc", > + .data = &sdhci_dwcmshc_th1520_pdata, > + }, > {}, > }; > MODULE_DEVICE_TABLE(of, sdhci_dwcmshc_dt_ids); > @@ -542,6 +866,30 @@ static int dwcmshc_probe(struct platform_device *pdev) > goto err_clk; > } > > + if (pltfm_data == &sdhci_dwcmshc_th1520_pdata) { > + priv->delay_line = PHY_SDCLKDL_DC_DEFAULT; > + > + if ((device_property_read_bool(dev, "mmc-ddr-1_8v")) | > + (device_property_read_bool(dev, "mmc-hs200-1_8v")) | > + (device_property_read_bool(dev, "mmc-hs400-1_8v"))) > + priv->flags |= FLAG_IO_FIXED_1V8; > + else > + priv->flags &= ~FLAG_IO_FIXED_1V8; > + > + /* > + * start_signal_voltage_switch() will try 3.3V first > + * then 1.8V. Use SDHCI_SIGNALING_180 rather than > + * SDHCI_SIGNALING_330 to avoid setting voltage to 3.3V > + * in sdhci_start_signal_voltage_switch(). > + */ > + if (priv->flags & FLAG_IO_FIXED_1V8) { > + host->flags &= ~SDHCI_SIGNALING_330; > + host->flags |= SDHCI_SIGNALING_180; > + } > + > + sdhci_enable_v4_mode(host); > + } > + > #ifdef CONFIG_ACPI > if (pltfm_data == &sdhci_dwcmshc_bf3_pdata) > sdhci_enable_v4_mode(host); >
On Mon, Nov 06, 2023 at 08:42:38PM +0200, Adrian Hunter wrote: > On 2/11/23 04:48, Drew Fustini wrote: > > Add support for the mmc controller in the T-Head TH1520 with the new > > compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for > > set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning. > > > > Signed-off-by: Drew Fustini <dfustini@baylibre.com> > > One question below, otherwise: > > Acked-by: Adrian Hunter <adrian.hunter@intel.com> > > > --- > > drivers/mmc/host/sdhci-of-dwcmshc.c | 348 ++++++++++++++++++++++++++++++++++++ > > 1 file changed, 348 insertions(+) > > > > diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c > > index 3a3bae6948a8..1a1386b742c1 100644 > > --- a/drivers/mmc/host/sdhci-of-dwcmshc.c > > +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c > > @@ -8,6 +8,7 @@ > > */ > > > > #include <linux/acpi.h> > > +#include <linux/bitfield.h> > > #include <linux/clk.h> > > #include <linux/dma-mapping.h> > > #include <linux/iopoll.h> > > @@ -35,6 +36,21 @@ > > #define DWCMSHC_CARD_IS_EMMC BIT(0) > > #define DWCMSHC_ENHANCED_STROBE BIT(8) > > #define DWCMSHC_EMMC_ATCTRL 0x40 > > +/* Tuning and auto-tuning fields in AT_CTRL_R control register */ > > +#define AT_CTRL_AT_EN BIT(0) /* autotuning is enabled */ > > +#define AT_CTRL_CI_SEL BIT(1) /* interval to drive center phase select */ > > +#define AT_CTRL_SWIN_TH_EN BIT(2) /* sampling window threshold enable */ > > +#define AT_CTRL_RPT_TUNE_ERR BIT(3) /* enable reporting framing errors */ > > +#define AT_CTRL_SW_TUNE_EN BIT(4) /* enable software managed tuning */ > > +#define AT_CTRL_WIN_EDGE_SEL_MASK GENMASK(11, 8) /* bits [11:8] */ > > +#define AT_CTRL_WIN_EDGE_SEL 0xf /* sampling window edge select */ > > +#define AT_CTRL_TUNE_CLK_STOP_EN BIT(16) /* clocks stopped during phase code change */ > > +#define AT_CTRL_PRE_CHANGE_DLY_MASK GENMASK(18, 17) /* bits [18:17] */ > > +#define AT_CTRL_PRE_CHANGE_DLY 0x1 /* 2-cycle latency */ > > +#define AT_CTRL_POST_CHANGE_DLY_MASK GENMASK(20, 19) /* bits [20:19] */ > > +#define AT_CTRL_POST_CHANGE_DLY 0x3 /* 4-cycle latency */ > > +#define AT_CTRL_SWIN_TH_VAL_MASK GENMASK(31, 24) /* bits [31:24] */ > > +#define AT_CTRL_SWIN_TH_VAL 0x9 /* sampling window threshold */ > > > > /* Rockchip specific Registers */ > > #define DWCMSHC_EMMC_DLL_CTRL 0x800 > > @@ -72,6 +88,82 @@ > > (((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0)) > > #define RK35xx_MAX_CLKS 3 > > > > +/* PHY register area pointer */ > > +#define DWC_MSHC_PTR_PHY_R 0x300 > > + > > +/* PHY general configuration */ > > +#define PHY_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x00) > > +#define PHY_CNFG_RSTN_DEASSERT 0x1 /* Deassert PHY reset */ > > +#define PHY_CNFG_PAD_SP_MASK GENMASK(19, 16) /* bits [19:16] */ > > +#define PHY_CNFG_PAD_SP 0x0c /* PMOS TX drive strength */ > > +#define PHY_CNFG_PAD_SN_MASK GENMASK(23, 20) /* bits [23:20] */ > > +#define PHY_CNFG_PAD_SN 0x0c /* NMOS TX drive strength */ > > + > > +/* PHY command/response pad settings */ > > +#define PHY_CMDPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x04) > > + > > +/* PHY data pad settings */ > > +#define PHY_DATAPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x06) > > + > > +/* PHY clock pad settings */ > > +#define PHY_CLKPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x08) > > + > > +/* PHY strobe pad settings */ > > +#define PHY_STBPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0a) > > + > > +/* PHY reset pad settings */ > > +#define PHY_RSTNPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0c) > > + > > +/* Bitfields are common for all pad settings */ > > +#define PHY_PAD_RXSEL_1V8 0x1 /* Receiver type select for 1.8V */ > > +#define PHY_PAD_RXSEL_3V3 0x2 /* Receiver type select for 3.3V */ > > + > > +#define PHY_PAD_WEAKPULL_MASK GENMASK(4, 3) /* bits [4:3] */ > > +#define PHY_PAD_WEAKPULL_PULLUP 0x1 /* Weak pull up enabled */ > > +#define PHY_PAD_WEAKPULL_PULLDOWN 0x2 /* Weak pull down enabled */ > > + > > +#define PHY_PAD_TXSLEW_CTRL_P_MASK GENMASK(8, 5) /* bits [8:5] */ > > +#define PHY_PAD_TXSLEW_CTRL_P 0x3 /* Slew control for P-Type pad TX */ > > +#define PHY_PAD_TXSLEW_CTRL_N_MASK GENMASK(12, 9) /* bits [12:9] */ > > +#define PHY_PAD_TXSLEW_CTRL_N 0x3 /* Slew control for N-Type pad TX */ > > + > > +/* PHY CLK delay line settings */ > > +#define PHY_SDCLKDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x1d) > > +#define PHY_SDCLKDL_CNFG_UPDATE BIT(4) /* set before writing to SDCLKDL_DC */ > > + > > +/* PHY CLK delay line delay code */ > > +#define PHY_SDCLKDL_DC_R (DWC_MSHC_PTR_PHY_R + 0x1e) > > +#define PHY_SDCLKDL_DC_INITIAL 0x40 /* initial delay code */ > > +#define PHY_SDCLKDL_DC_DEFAULT 0x32 /* default delay code */ > > +#define PHY_SDCLKDL_DC_HS400 0x18 /* delay code for HS400 mode */ > > + > > +/* PHY drift_cclk_rx delay line configuration setting */ > > +#define PHY_ATDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x21) > > +#define PHY_ATDL_CNFG_INPSEL_MASK GENMASK(3, 2) /* bits [3:2] */ > > +#define PHY_ATDL_CNFG_INPSEL 0x3 /* delay line input source */ > > + > > +/* PHY DLL control settings */ > > +#define PHY_DLL_CTRL_R (DWC_MSHC_PTR_PHY_R + 0x24) > > +#define PHY_DLL_CTRL_DISABLE 0x0 /* PHY DLL is enabled */ > > +#define PHY_DLL_CTRL_ENABLE 0x1 /* PHY DLL is disabled */ > > + > > +/* PHY DLL configuration register 1 */ > > +#define PHY_DLL_CNFG1_R (DWC_MSHC_PTR_PHY_R + 0x25) > > +#define PHY_DLL_CNFG1_SLVDLY_MASK GENMASK(5, 4) /* bits [5:4] */ > > +#define PHY_DLL_CNFG1_SLVDLY 0x2 /* DLL slave update delay input */ > > +#define PHY_DLL_CNFG1_WAITCYCLE 0x5 /* DLL wait cycle input */ > > + > > +/* PHY DLL configuration register 2 */ > > +#define PHY_DLL_CNFG2_R (DWC_MSHC_PTR_PHY_R + 0x26) > > +#define PHY_DLL_CNFG2_JUMPSTEP 0xa /* DLL jump step input */ > > + > > +/* PHY DLL master and slave delay line configuration settings */ > > +#define PHY_DLLDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x28) > > +#define PHY_DLLDL_CNFG_SLV_INPSEL_MASK GENMASK(6, 5) /* bits [6:5] */ > > +#define PHY_DLLDL_CNFG_SLV_INPSEL 0x3 /* clock source select for slave DL */ > > + > > +#define FLAG_IO_FIXED_1V8 BIT(0) > > + > > #define BOUNDARY_OK(addr, len) \ > > ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1))) > > > > @@ -92,6 +184,8 @@ struct dwcmshc_priv { > > struct clk *bus_clk; > > int vendor_specific_area1; /* P_VENDOR_SPECIFIC_AREA reg */ > > void *priv; /* pointer to SoC private stuff */ > > + u16 delay_line; > > + u16 flags; > > }; > > > > /* > > @@ -157,6 +251,126 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq) > > sdhci_request(mmc, mrq); > > } > > > > +static void dwcmshc_phy_1_8v_init(struct sdhci_host *host) > > +{ > > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > > + u32 val; > > + > > + /* deassert phy reset & set tx drive strength */ > > + val = PHY_CNFG_RSTN_DEASSERT; > > + val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP); > > + val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN); > > + sdhci_writel(host, val, PHY_CNFG_R); > > + > > + /* disable delay line */ > > + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R); > > + > > + /* set delay line */ > > + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R); > > + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R); > > + > > + /* enable delay lane */ > > + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R); > > + val &= ~(PHY_SDCLKDL_CNFG_UPDATE); > > + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R); > > + > > + /* configure phy pads */ > > + val = PHY_PAD_RXSEL_1V8; > > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R); > > + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R); > > + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R); > > + > > + val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R); > > + > > + val = PHY_PAD_RXSEL_1V8; > > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_STBPAD_CNFG_R); > > + > > + /* enable data strobe mode */ > > + sdhci_writeb(host, FIELD_PREP(PHY_DLLDL_CNFG_SLV_INPSEL_MASK, PHY_DLLDL_CNFG_SLV_INPSEL), > > + PHY_DLLDL_CNFG_R); > > + > > + /* enable phy dll */ > > + sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R); > > +} > > + > > +static void dwcmshc_phy_3_3v_init(struct sdhci_host *host) > > +{ > > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > > + u32 val; > > + > > + /* deassert phy reset & set tx drive strength */ > > + val = PHY_CNFG_RSTN_DEASSERT; > > + val |= FIELD_PREP(PHY_CNFG_PAD_SP_MASK, PHY_CNFG_PAD_SP); > > + val |= FIELD_PREP(PHY_CNFG_PAD_SN_MASK, PHY_CNFG_PAD_SN); > > + sdhci_writel(host, val, PHY_CNFG_R); > > + > > + /* disable delay line */ > > + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE, PHY_SDCLKDL_CNFG_R); > > + > > + /* set delay line */ > > + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R); > > + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R); > > + > > + /* enable delay lane */ > > + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R); > > + val &= ~(PHY_SDCLKDL_CNFG_UPDATE); > > + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R); > > + > > + /* configure phy pads */ > > + val = PHY_PAD_RXSEL_3V3; > > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLUP); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R); > > + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R); > > + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R); > > + > > + val = FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R); > > + > > + val = PHY_PAD_RXSEL_3V3; > > + val |= FIELD_PREP(PHY_PAD_WEAKPULL_MASK, PHY_PAD_WEAKPULL_PULLDOWN); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_P_MASK, PHY_PAD_TXSLEW_CTRL_P); > > + val |= FIELD_PREP(PHY_PAD_TXSLEW_CTRL_N_MASK, PHY_PAD_TXSLEW_CTRL_N); > > + sdhci_writew(host, val, PHY_STBPAD_CNFG_R); > > + > > + /* enable phy dll */ > > + sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R); > > +} > > + > > +static void th1520_sdhci_set_phy(struct sdhci_host *host) > > +{ > > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > > + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host); > > + u16 emmc_ctrl; > > + > > + /* Before power on, set PHY configs */ > > + if (priv->flags & FLAG_IO_FIXED_1V8) > > + dwcmshc_phy_1_8v_init(host); > > + else > > + dwcmshc_phy_3_3v_init(host); > > + > > + if (host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) { > > Perhaps you mean both MMC_CAP2_NO_SD and MMC_CAP2_NO_SDIO which would be as below? > > if ((host->mmc->caps2 & (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) == (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO)) { > > or > > if (host->mmc->caps2 & MMC_CAP2_NO_SD && host->mmc->caps2 & MMC_CAP2_NO_SDIO) { > > or some such? Thanks for catching this. Yes, what I did is incorrect. In fact, Jisheng had suggested this code in the v2 thread: u32 tmp = MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO; if ((cap2 & tmp) == tmp) { blablabla... } This is similar to your first suggestion above. I'll fix this in v5. thanks, drew
This series adds support for the MMC controller in the T-Head TH1520 SoC, and it enables the eMMC and microSD slot on both the BeagleV Ahead and the Sipeed LicheePi 4A. I tested on top of v6.6 with riscv defconfig. I was able to boot the Ahead [1] and LPi4a [2] from eMMC. This patch series also exists as a git branch [3]. Note: I have only tested eMMC and microSD. I have not yet configured or tested the mmc controller used for SDIO WiFi yet. References: [1] https://gist.github.com/pdp7/881342620ec1509685f23a387e2fc8d7 [2] https://gist.github.com/pdp7/97017ad88d83fccac18eba69bff817b7 [3] https://github.com/pdp7/linux/tree/b4/th1520-mmc Changes in PATCH v4: - set DWCMSHC_CARD_IS_EMMC when (MMC_CAP2_NO_SD | MMC_CAP2_NO_SDIO) as checking MMC_CAP_NONREMOVABLE is not sufficient - change prefix of phy functions from th1520 to dwcmshc as they are not th1520 specific - remove unneeded check of priv in dwcmshc_phy_1_8v_init() - remove unneeded check of auto-tuning in th1520_execute_tuning() - fix order of new nodes in th1520-beaglev-ahead.dts: move sdhci_clk before uart_sclk, move mmc0 and mmc1 before uart0 - fix comment typos pointed out by Adrian - add trailers that I missed from v2 Changes in PATCH v3: https://lore.kernel.org/r/20231023-th1520-mmc-v3-0-abc5e7491166@baylibre.com - always call th1520_sdhci_set_phy() in th1520_set_uhs_signaling() and not only when timing is MMC_TIMING_MMC_HS400. This allows the microSD slot to work as th1520_phy_3_3v_init() is called from th1520_sdhci_set_phy(). - add mmc1 node for mmc controller connected to the microSD slot - add enable mmc1 and add properties for microSD on the Ahead and LPi4A Changes in PATCH v2: https://lore.kernel.org/r/20231017-th1520-mmc-v2-0-4678c8cc4048@baylibre.com - make use of BIT(), GENMASK(), FIELD_PREP(), FIELD_GET() - add EXPORT_SYMBOL_GPL(__sdhci_execute_tuning) - call th1520_phy_1_8v_init() when FLAG_IO_FIXED_1V8 is set - set DWCMSHC_CARD_IS_EMMC when mmc caps contains MMC_CAP_NONREMOVABLE - remove manipulation of AT_CTRL_AT_EN from th1520_set_uhs_signaling() - remove unneccessary cycle of enabling and disabling AT_CTRL_AT_EN in th1520_execute_tuning() - remove th1520_phy_1_8v_init_no_pull() - remove th1520_phy_3_3v_init_no_pull() - remove FLAG_PULL_UP_EN from priv->flags - remove thead,phy-pull-up device tree property Changes in PACH v1: https://lore.kernel.org/all/20230921-th1520-mmc-v1-0-49f76c274fb3@baylibre.com/ - ADMA mode now works correctly due to a patch from Jisheng on the list ("riscv: dts: thead: set dma-noncoherent to soc bus") and this commit from Icenowy that is now merged: 8eb8fe67e2c8 ("riscv: errata: fix T-Head dcache.cva encoding"). - Expose __sdhci_execute_tuning from sdhci.c so that it can be called from th1520_execute_tuning() - Refactor the define macros for all the PHY related registers to make it easier to understand the bit fields that the code is manipulating - Replace magic numbers in the PHY register writes with proper defines - Replace non_removable in dwcmshc_priv with check of mmc_host.caps - Drop dt prop "thead,io-fixed-1v8" and instead check for existing properties: "mmc-ddr-1_8v", "mmc-hs200-1_8v", or "mmc-hs400-1_8v" - Rename dt prop from "thead,pull-up" to "thead,phy-pull-up" and improve the description in the dt binding - Replace pull_up_en in dwcmshc_priv with bit field in new flags field - Create th1520_set_uhs_signaling() and call dwcmshc_set_uhs_signaling() from it instead of adding th1520 code to dwcmshc_set_uhs_signaling() - Return -EIO instead of -1 upon errors in th1520_execute_tuning() Changes in RFC v2: https://lore.kernel.org/linux-riscv/20230724-th1520-emmc-v2-0-132ed2e2171e@baylibre.com/ - Expand dwcmshc_priv based on driver in the T-Head 5.10 kernel: delay_line, non_removable, pull_up_en, io_fixed_1v8 - New boolean property "thead,pull-up" indicates phy pull-up config - New boolean property "thead,io-fixed-1v8" indicates that io voltage should be set to 1.8V during reset - Add th1520_phy_1_8v_init() as voltage_switch op - Add th1520_execute_tuning() as the platform_execute_tuning op - Added th1520_sdhci_reset() as the .reset op. This function will set io voltage to 1.8V after calling the standard sdhci_reset() function. - Modified dwcmshc_set_uhs_signaling() to enable SDHCI_CTRL_VDD_180 when io_fixed_1v8 is true - Add many defines for register offsets and settings based on the mmc support in the T-Head downstream v5.10 kernel RFC v1 series: https://lore.kernel.org/r/20230724-th1520-emmc-v1-0-cca1b2533da2@baylibre.com Signed-off-by: Drew Fustini <dfustini@baylibre.com> --- Drew Fustini (7): dt-bindings: mmc: sdhci-of-dwcmhsc: Add T-Head TH1520 support mmc: sdhci: add __sdhci_execute_tuning() to header mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520 riscv: defconfig: Enable mmc and dma drivers for T-Head TH1520 riscv: dts: thead: Add TH1520 mmc controllers and sdhci clock riscv: dts: thead: Enable BeagleV Ahead eMMC and microSD riscv: dts: thead: Enable LicheePi 4A eMMC and microSD .../bindings/mmc/snps,dwcmshc-sdhci.yaml | 1 + arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts | 20 ++ .../boot/dts/thead/th1520-lichee-module-4a.dtsi | 20 ++ arch/riscv/boot/dts/thead/th1520.dtsi | 23 ++ arch/riscv/configs/defconfig | 2 + drivers/mmc/host/sdhci-of-dwcmshc.c | 348 +++++++++++++++++++++ drivers/mmc/host/sdhci.c | 3 +- drivers/mmc/host/sdhci.h | 1 + 8 files changed, 417 insertions(+), 1 deletion(-) --- base-commit: 8cfd133bee055fb537d2338b808079a77de60052 change-id: 20231031-th1520-mmc-b4e846fe6869 Best regards,