@@ -1992,7 +1992,6 @@ static int i40iw_addr_resolve_neigh(struct i40iw_device *iwdev,
/**
* i40iw_get_dst_ipv6
*/
-#if IS_ENABLED(CONFIG_IPV6)
static struct dst_entry *i40iw_get_dst_ipv6(struct sockaddr_in6 *src_addr,
struct sockaddr_in6 *dst_addr)
{
@@ -2008,7 +2007,6 @@ static struct dst_entry *i40iw_get_dst_ipv6(struct sockaddr_in6 *src_addr,
dst = ip6_route_output(&init_net, NULL, &fl6);
return dst;
}
-#endif
/**
* i40iw_addr_resolve_neigh_ipv6 - resolve neighbor ipv6 address
@@ -2016,7 +2014,6 @@ static struct dst_entry *i40iw_get_dst_ipv6(struct sockaddr_in6 *src_addr,
* @dst_ip: remote ip address
* @arpindex: if there is an arp entry
*/
-#if IS_ENABLED(CONFIG_IPV6)
static int i40iw_addr_resolve_neigh_ipv6(struct i40iw_device *iwdev,
u32 *src,
u32 *dest,
@@ -2089,7 +2086,6 @@ static int i40iw_addr_resolve_neigh_ipv6(struct i40iw_device *iwdev,
dst_release(dst);
return rc;
}
-#endif
/**
* i40iw_ipv4_is_loopback - check if loopback
@@ -2190,13 +2186,13 @@ static struct i40iw_cm_node *i40iw_make_cm_node(
cm_info->loc_addr[0],
cm_info->rem_addr[0],
oldarpindex);
-#if IS_ENABLED(CONFIG_IPV6)
- else
+ else if (IS_ENABLED(CONFIG_IPV6))
arpindex = i40iw_addr_resolve_neigh_ipv6(iwdev,
cm_info->loc_addr,
cm_info->rem_addr,
oldarpindex);
-#endif
+ else
+ arpindex = -EINVAL;
}
if (arpindex < 0) {
i40iw_pr_err("cm_node arpindex\n");
gcc finds that the i40iw_make_cm_node() function in the recently added i40iw driver uses an uninitilized variable as an index into an array if CONFIG_IPV6 is disabled and the driver uses IPv6 mode: drivers/infiniband/hw/i40iw/i40iw_cm.c: In function 'i40iw_make_cm_node': drivers/infiniband/hw/i40iw/i40iw_cm.c:2206:52: error: 'arpindex' may be used uninitialized in this function [-Werror=maybe-uninitialized] ether_addr_copy(cm_node->rem_mac, iwdev->arp_table[arpindex].mac_addr); As far as I can tell, this code path can not be used because the ipv4 variable is always set with CONFIG_IPV6 is disabled, but it's better to be sure and prevent the undefined behavior, as well as shut up that warning in a proper way. This adds an 'else' clause for the case we get the warning about, causing the function to return an error in a controlled way. To avoid adding extra mess with combined io()/#ifdef clauses, I'm also converting the existing #ifdef into a more readable if(IS_ENABLED()) check. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: f27b4746f378 ("i40iw: add connection management code") --- drivers/infiniband/hw/i40iw/i40iw_cm.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-) -- 2.7.0