new file mode 100644
@@ -0,0 +1,171 @@
+CS35L35 Boosted Speaker Amplifier
+
+Required properties:
+
+ - compatible : "cirrus,cs35l35"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply : power supplies for the device,
+ as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+ - interrupt-parent : Specifies the phandle of the interrupt controller to
+ which the IRQs from CS35L35 are delivered to.
+ - interrupts : IRQ line info CS35L35.
+ (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+ for further information relating to interrupt properties)
+
+Optional properties:
+ - reset-gpios : gpio used to reset the amplifier
+
+ - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
+ Stereo configuration
+
+ - cirrus,audio-channel : Set Location of Audio Signal on Serial Port
+ 0 = Data Packet received on Left I2S Channel
+ 1 = Data Packet received on Right I2S Channel
+
+ - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port
+ 0 = Data Packet received on Left I2S Channel
+ 1 = Data Packet received on Right I2S Channel
+
+ - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
+ if 2 Devices share Boost BST_CTL
+
+ - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength
+ Table 3-10 of the datasheet lists drive-strength specifications
+ 0 = 1x (Default)
+ 1 = .5x
+
+ - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
+ powers down with a rectification FET On or Off. If VSPK is supplied
+ externally then FET is off.
+
+ - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
+ converter's output voltage in mV. The range is from 2600mV to 9000mV with
+ increments of 100mV.
+ (Default) VP
+
+ - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
+ Configures the peak current by monitoring the current through the boost FET.
+ Range starts at 1680mA and goes to a maximum of 4480mA with increments of
+ 110mA.
+ (Default) 2.46 Amps
+
+ - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change
+ zero-cross
+
+Optional H/G Algorithm sub-node:
+
+ The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node
+ that will disable automatic control of the internal H/G Algorithm.
+
+ It is strongly recommended that the Datasheet be referenced when adjusting
+ or using these Class H Algorithm controls over the internal Algorithm.
+ Serious damage can occur to the Device and surrounding components.
+
+ - cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm
+ See Section 4.3 Internal Class H Algorithm in the Datasheet.
+ If not used, the device manages the ClassH Algorithm internally.
+
+Optional properties for the "cirrus,classh-internal-algo" Sub-node
+
+ Section 7.29 Class H Control
+ - cirrus,classh-bst-overide : Boolean
+ - cirrus,classh-bst-max-limit
+ - cirrus,classh-mem-depth
+
+ Section 7.30 Class H Headroom Control
+ - cirrus,classh-headroom
+
+ Section 7.31 Class H Release Rate
+ - cirrus,classh-release-rate
+
+ Section 7.32 Class H Weak FET Drive Control
+ - cirrus,classh-wk-fet-disable
+ - cirrus,classh-wk-fet-delay
+ - cirrus,classh-wk-fet-thld
+
+ Section 7.34 Class H VP Control
+ - cirrus,classh-vpch-auto
+ - cirrus,classh-vpch-rate
+ - cirrus,classh-vpch-man
+
+Optional Monitor Signal Format sub-node:
+
+ The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node
+ for adjusting the Depth, Location and Frame of the Monitoring Signals
+ for Algorithms.
+
+ See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet
+
+ -cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formating
+ on the I2S Port. Each of the 3 8 bit values in the array contain the settings
+ for depth, location, and frame.
+
+ If not used, the defaults for the 6 monitor signals is used.
+
+ Sections 7.44 - 7.53 lists values for the depth, location, and frame
+ for each monitoring signal.
+
+ - cirrus,imon : 3 8 bit values to set the depth, location, and frame
+ of the IMON monitor signal.
+
+ - cirrus,vmon : 3 8 bit values to set the depth, location, and frame
+ of the VMON monitor signal.
+
+ - cirrus,vpmon : 3 8 bit values to set the depth, location, and frame
+ of the VPMON monitor signal.
+
+ - cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame
+ of the VBSTMON monitor signal
+
+ - cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame
+ of the VPBRSTAT monitor signal
+
+ - cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\
+ of the ZEROFILL packet in the monitor signal
+
+Example:
+
+cs35l35: cs35l35@20 {
+ compatible = "cirrus,cs35l35";
+ reg = <0x20>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ reset-gpios = <&axi_gpio 54 0>;
+ interrupt-parent = <&gpio8>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ cirrus,boost-ctl-millivolt = <9000>;
+
+ cirrus,stereo-config;
+ cirrus,audio-channel = <0x00>;
+ cirrus,advisory-channel = <0x01>;
+ cirrus,shared-boost;
+
+ cirrus,classh-internal-algo {
+ cirrus,classh-bst-overide;
+ cirrus,classh-bst-max-limit = <0x01>;
+ cirrus,classh-mem-depth = <0x01>;
+ cirrus,classh-release-rate = <0x08>;
+ cirrus,classh-headroom-millivolt = <0x0B>;
+ cirrus,classh-wk-fet-disable = <0x01>;
+ cirrus,classh-wk-fet-delay = <0x04>;
+ cirrus,classh-wk-fet-thld = <0x01>;
+ cirrus,classh-vpch-auto = <0x01>;
+ cirrus,classh-vpch-rate = <0x02>;
+ cirrus,classh-vpch-man = <0x05>;
+ };
+
+ /* Depth, Location, Frame */
+ cirrus,monitor-signal-format {
+ cirrus,imon = /bits/ 8 <0x03 0x00 0x01>;
+ cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>;
+ cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>;
+ cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>;
+ cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>;
+ cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>;
+ };
+
+};