@@ -1028,24 +1028,25 @@ static int denali_setup_data_interface(struct mtd_info *mtd, int chipnr,
static void denali_reset_banks(struct denali_nand_info *denali)
{
+ u32 irq_status;
int i;
- denali_clear_irq_all(denali);
-
for (i = 0; i < denali->max_banks; i++) {
- iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
- while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
- (INTR__RST_COMP | INTR__TIME_OUT)))
- cpu_relax();
- if (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
- INTR__INT_ACT))
+ denali->flash_bank = i;
+
+ denali_reset_irq(denali);
+
+ iowrite32(DEVICE_RESET__BANK(i),
+ denali->flash_reg + DEVICE_RESET);
+
+ irq_status = denali_wait_for_irq(denali,
+ INTR__RST_COMP | INTR__INT_ACT | INTR__TIME_OUT);
+ if (!(irq_status & INTR__INT_ACT))
break;
}
dev_dbg(denali->dev, "%d chips connected\n", i);
denali->max_banks = i;
-
- denali_clear_irq_all(denali);
}
static void denali_hw_init(struct denali_nand_info *denali)
@@ -1067,7 +1068,6 @@ static void denali_hw_init(struct denali_nand_info *denali)
denali->bbtskipbytes = ioread32(denali->flash_reg +
SPARE_AREA_SKIP_BYTES);
detect_max_banks(denali);
- denali_reset_banks(denali);
iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED);
iowrite32(CHIP_EN_DONT_CARE__FLAG,
denali->flash_reg + CHIP_ENABLE_DONT_CARE);
@@ -1185,9 +1185,6 @@ static void denali_drv_init(struct denali_nand_info *denali)
* element that might be access shared data (interrupt status)
*/
spin_lock_init(&denali->irq_lock);
-
- /* indicate that MTD has not selected a valid bank yet */
- denali->flash_bank = CHIP_SELECT_INVALID;
}
static int denali_multidev_fixup(struct denali_nand_info *denali)
@@ -1262,6 +1259,9 @@ int denali_init(struct denali_nand_info *denali)
}
denali_enable_irq(denali);
+ denali_reset_banks(denali);
+
+ denali->flash_bank = CHIP_SELECT_INVALID;
nand_set_flash_node(chip, denali->dev->of_node);
/* Fallback to the default name if DT did not give "label" property */
The current bank reset implementation polls the INTR_STATUS register until interested bits are set. This is not good because: - polling simply wastes time-slice of the thread - The while() loop may continue eternally if no bit is set, for example, due to the controller problem. The denali_wait_for_irq() uses wait_for_completion_timeout(), which is safer. We can use interrupt by moving the denali_reset_bank() call below the interrupt setup. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> --- Changes in v7: None Changes in v6: None Changes in v5: None Changes in v4: None Changes in v3: None Changes in v2: - Newly added drivers/mtd/nand/denali.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-) -- 2.7.4