@@ -27,6 +27,7 @@ LIB := $(obj)libsound.o
COBJS-$(CONFIG_SOUND) += sound.o
COBJS-$(CONFIG_I2S) += i2s.o
+COBJS-$(CONFIG_SOUND_WM8994) += wm8994.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
new file mode 100644
@@ -0,0 +1,781 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ * R. Chandrasekar <rcsekar@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#define DEBUG
+#include <asm/arch/clk.h>
+#include <asm/arch/cpu.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <common.h>
+#include <div64.h>
+#include <i2c.h>
+#include <i2s.h>
+#include <sound.h>
+#include "wm8994.h"
+#include "wm8994_registers.h"
+
+/* defines for wm8994 system clock selection */
+#define SEL_MCLK1 0x00
+#define SEL_MCLK2 0x08
+#define SEL_FLL1 0x10
+#define SEL_FLL2 0x18
+
+/* fll config to configure fll */
+struct wm8994_fll_config {
+ int src; /* Source */
+ int in; /* Input frequency in Hz */
+ int out; /* output frequency in Hz */
+};
+
+/* codec private data */
+struct wm8994_priv {
+ enum wm8994_type type; /* codec type of wolfson */
+ int revision; /* Revision */
+ int sysclk[WM8994_MAX_AIF]; /* System clock freqency in Hz */
+ int mclk[WM8994_MAX_AIF]; /* master clock frequency in Hz */
+ int aifclk[WM8994_MAX_AIF]; /* audio interfce clock in Hz */
+ struct wm8994_fll_config fll[2]; /* fll config to configure fll */
+};
+
+/* wm 8994 supported sampling rate vlaues */
+static unsigned int src_rate[] = {
+ 8000, 11025, 12000, 16000, 22050, 24000,
+ 32000, 44100, 48000, 88200, 96000
+};
+
+/* op clock divisions */
+static int opclk_divs[] = { 10, 20, 30, 40, 55, 60, 80, 120, 160 };
+
+/* lr clock framsize ratio */
+static int fs_ratios[] = {
+ 64, 128, 192, 256, 348, 512, 768, 1024, 1408, 1536
+};
+
+/* bit clock divisions */
+static int bclk_divs[] = {
+ 10, 15, 20, 30, 40, 50, 60, 80, 110, 120, 160, 220, 240, 320, 440, 480,
+ 640, 880, 960, 1280, 1760, 1920
+};
+
+/* Global */
+struct wm8994_priv g_wm8994_info;
+unsigned int g_wm8994_i2c_dev_addr;
+
+/*
+ * Initialise I2C for wm 8994
+ *
+ * @param bus no i2c bus number in which wm8994 is connected
+ */
+static void wm8994_i2c_init(int bus_no)
+{
+ i2c_set_bus_num(bus_no);
+}
+
+/*
+ * Writes value to a device register through i2c
+ *
+ * @param reg reg number to be write
+ * @param data data to be writen to the above registor
+ *
+ * @return int value 1 for change, 0 for no change or negative error code.
+ */
+static int wm8994_i2c_write(unsigned int reg, unsigned short data)
+{
+ unsigned char val[2];
+
+ val[0] = (unsigned char)((data >> 8) & 0xff);
+ val[1] = (unsigned char)(data & 0xff);
+ debug("Write Addr : 0x%04X, Data : 0x%04X\n", reg, data);
+
+ return i2c_write(g_wm8994_i2c_dev_addr, reg, 2, val, 2);
+}
+
+/*
+ * Read a value from a device register through i2c
+ *
+ * @param reg reg number to be read
+ * @param data address of read data to be stored
+ *
+ * @return int value 0 for success, -1 in case of error.
+ */
+static unsigned int wm8994_i2c_read(unsigned int reg , unsigned short *data)
+{
+ unsigned char val[2];
+ int ret;
+
+ ret = i2c_read(g_wm8994_i2c_dev_addr, reg, 2, val, 2);
+ if (ret != 0) {
+ debug("%s: Error while reading register %#04x\n",
+ __func__, reg);
+ return -1;
+ }
+ *data = val[0];
+ *data <<= 8;
+ *data |= val[1];
+
+ return 0;
+}
+
+/*
+ * update device register bits through i2c
+ *
+ * @param reg codec register
+ * @param mask register mask
+ * @param value new value
+ *
+ * @return int value 1 for change, 0 for no change or negative error code.
+ */
+static int wm8994_update_bits(unsigned int reg, unsigned short mask,
+ unsigned short value)
+{
+ int change , ret = 0;
+ unsigned short old, new;
+
+ if (wm8994_i2c_read(reg, &old) != 0)
+ return -1;
+ new = (old & ~mask) | (value & mask);
+ change = (old != new) ? 1 : 0;
+ if (change)
+ ret = wm8994_i2c_write(reg, new);
+ if (ret < 0)
+ return ret;
+
+ return change;
+}
+
+/*
+ * Sets i2s set format
+ *
+ * @param aif_id Interface ID
+ * @param fmt i2S format
+ *
+ * @return -1 for error and 0 Success.
+ */
+int wm8994_set_fmt(int aif_id, unsigned int fmt)
+{
+ int ms_reg;
+ int aif_reg;
+ int ms = 0;
+ int aif = 0;
+ int aif_clk = 0;
+ int error = 0;
+
+ switch (aif_id) {
+ case 1:
+ ms_reg = WM8994_AIF1_MASTER_SLAVE;
+ aif_reg = WM8994_AIF1_CONTROL_1;
+ aif_clk = WM8994_AIF1_CLOCKING_1;
+ break;
+ case 2:
+ ms_reg = WM8994_AIF2_MASTER_SLAVE;
+ aif_reg = WM8994_AIF2_CONTROL_1;
+ aif_clk = WM8994_AIF2_CLOCKING_1;
+ break;
+ default:
+ debug("%s: Invalid audio interface selection\n", __func__);
+ return -1;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBS_CFS:
+ break;
+ case SND_SOC_DAIFMT_CBM_CFM:
+ ms = WM8994_AIF1_MSTR;
+ break;
+ default:
+ debug("%s: Invalid i2s master selection\n", __func__);
+ return -1;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_DSP_B:
+ aif |= WM8994_AIF1_LRCLK_INV;
+ case SND_SOC_DAIFMT_DSP_A:
+ aif |= 0x18;
+ break;
+ case SND_SOC_DAIFMT_I2S:
+ aif |= 0x10;
+ break;
+ case SND_SOC_DAIFMT_RIGHT_J:
+ break;
+ case SND_SOC_DAIFMT_LEFT_J:
+ aif |= 0x8;
+ break;
+ default:
+ debug("%s: Invalid i2s format selection\n", __func__);
+ return -1;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_DSP_A:
+ case SND_SOC_DAIFMT_DSP_B:
+ /* frame inversion not valid for DSP modes */
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ aif |= WM8994_AIF1_BCLK_INV;
+ break;
+ default:
+ debug("%s: Invalid i2s frame inverse selection\n",
+ __func__);
+ return -1;
+ }
+ break;
+
+ case SND_SOC_DAIFMT_I2S:
+ case SND_SOC_DAIFMT_RIGHT_J:
+ case SND_SOC_DAIFMT_LEFT_J:
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_IF:
+ aif |= WM8994_AIF1_BCLK_INV | WM8994_AIF1_LRCLK_INV;
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ aif |= WM8994_AIF1_BCLK_INV;
+ break;
+ case SND_SOC_DAIFMT_NB_IF:
+ aif |= WM8994_AIF1_LRCLK_INV;
+ break;
+ default:
+ debug("%s: Invalid i2s clock polarity selection\n",
+ __func__);
+ return -1;
+ }
+ break;
+ default:
+ debug("%s: Invalid i2s format selection\n", __func__);
+ return -1;
+ }
+
+ error = wm8994_update_bits(aif_reg, WM8994_AIF1_BCLK_INV |
+ WM8994_AIF1_LRCLK_INV_MASK | WM8994_AIF1_FMT_MASK, aif);
+
+ error |= wm8994_update_bits(ms_reg, WM8994_AIF1_MSTR_MASK, ms);
+ error |= wm8994_update_bits(aif_clk, WM8994_AIF1CLK_ENA_MASK,
+ WM8994_AIF1CLK_ENA);
+ if (error < 0) {
+ debug("%s: codec register access error\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Sets hw params FOR WM8994
+ *
+ * @param sampling_rate Sampling rate
+ * @param bits_per_sample Bits per sample
+ * @param Channels Channels in the given audio input
+ *
+ * @return -1 for error and 0 Success.
+ */
+static int wm8994_hw_params(struct wm8994_priv *wm8994, int aif_id,
+ unsigned int sampling_rate, unsigned int bits_per_sample,
+ unsigned int channels)
+{
+ int aif1_reg;
+ int aif2_reg;
+ int bclk_reg;
+ int bclk = 0;
+ int rate_reg;
+ int aif1 = 0;
+ int aif2 = 0;
+ int rate_val = 0;
+ int id = aif_id - 1;
+ int i, cur_val, best_val, bclk_rate, best;
+ unsigned short reg_data;
+ int ret = 0;
+
+ switch (aif_id) {
+ case 1:
+ aif1_reg = WM8994_AIF1_CONTROL_1;
+ aif2_reg = WM8994_AIF1_CONTROL_2;
+ bclk_reg = WM8994_AIF1_BCLK;
+ rate_reg = WM8994_AIF1_RATE;
+ break;
+ case 2:
+ aif1_reg = WM8994_AIF2_CONTROL_1;
+ aif2_reg = WM8994_AIF2_CONTROL_2;
+ bclk_reg = WM8994_AIF2_BCLK;
+ rate_reg = WM8994_AIF2_RATE;
+ break;
+ default:
+ return -1;
+ }
+
+ bclk_rate = sampling_rate * 32;
+ switch (bits_per_sample) {
+ case 16:
+ bclk_rate *= 16;
+ break;
+ case 20:
+ bclk_rate *= 20;
+ aif1 |= 0x20;
+ break;
+ case 24:
+ bclk_rate *= 24;
+ aif1 |= 0x40;
+ break;
+ case 32:
+ bclk_rate *= 32;
+ aif1 |= 0x60;
+ break;
+ default:
+ return -1;
+ }
+
+ /* Try to find an appropriate sample rate; look for an exact match. */
+ for (i = 0; i < ARRAY_SIZE(src_rate); i++)
+ if (src_rate[i] == sampling_rate)
+ break;
+
+ if (i == ARRAY_SIZE(src_rate)) {
+ debug("%s: Could not get the best matching samplingrate\n",
+ __func__);
+ return -1;
+ }
+
+ rate_val |= i << WM8994_AIF1_SR_SHIFT;
+
+ /* AIFCLK/fs ratio; look for a close match in either direction */
+ best = 0;
+ best_val = abs((fs_ratios[0] * sampling_rate)
+ - wm8994->aifclk[id]);
+
+ for (i = 1; i < ARRAY_SIZE(fs_ratios); i++) {
+ cur_val = abs((fs_ratios[i] * sampling_rate)
+ - wm8994->aifclk[id]);
+ if (cur_val >= best_val)
+ continue;
+ best = i;
+ best_val = cur_val;
+ }
+
+ rate_val |= best;
+
+ /*
+ * We may not get quite the right frequency if using
+ * approximate clocks so look for the closest match that is
+ * higher than the target (we need to ensure that there enough
+ * BCLKs to clock out the samples).
+ */
+ best = 0;
+ for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
+ cur_val = (wm8994->aifclk[id] * 10 / bclk_divs[i]) - bclk_rate;
+ if (cur_val < 0) /* BCLK table is sorted */
+ break;
+ best = i;
+ }
+
+ if (i == ARRAY_SIZE(bclk_divs)) {
+ debug("%s: Could not get the best matching bclk division\n",
+ __func__);
+ return -1;
+ }
+
+ bclk_rate = wm8994->aifclk[id] * 10 / bclk_divs[best];
+ bclk |= best << WM8994_AIF1_BCLK_DIV_SHIFT;
+
+ if (wm8994_i2c_read(aif1_reg, ®_data) != 0)
+ return -1;
+
+ if ((channels == 1) && ((reg_data & 0x18) == 0x18))
+ aif2 |= WM8994_AIF1_MONO;
+
+ if (wm8994->aifclk[id] == 0)
+ return -1;
+
+ ret = wm8994_update_bits(aif1_reg, WM8994_AIF1_WL_MASK, aif1);
+ ret |= wm8994_update_bits(aif2_reg, WM8994_AIF1_MONO, aif2);
+ ret |= wm8994_update_bits(bclk_reg, WM8994_AIF1_BCLK_DIV_MASK, bclk);
+ ret |= wm8994_update_bits(rate_reg, WM8994_AIF1_SR_MASK |
+ WM8994_AIF1CLK_RATE_MASK, rate_val);
+
+ debug("rate vale = %x , bclk val= %x\n", rate_val, bclk);
+
+ if (ret < 0) {
+ debug("%s: codec register access error\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Configures Audio interface Clock
+ *
+ * @param wm8994 wm8994 information pointer
+ * @param aif Audio Interface ID
+ *
+ * @return -1 for error and 0 Success.
+ */
+static int configure_aif_clock(struct wm8994_priv *wm8994, int aif)
+{
+ int rate;
+ int reg1 = 0;
+ int offset;
+ int ret;
+
+ if (aif)
+ offset = 4;
+ else
+ offset = 0;
+
+ switch (wm8994->sysclk[aif]) {
+ case WM8994_SYSCLK_MCLK1:
+ reg1 |= SEL_MCLK1;
+ rate = wm8994->mclk[0];
+ break;
+
+ case WM8994_SYSCLK_MCLK2:
+ reg1 |= SEL_MCLK2;
+ rate = wm8994->mclk[1];
+ break;
+
+ case WM8994_SYSCLK_FLL1:
+ reg1 |= SEL_FLL1;
+ rate = wm8994->fll[0].out;
+ break;
+
+ case WM8994_SYSCLK_FLL2:
+ reg1 |= SEL_FLL2;
+ rate = wm8994->fll[1].out;
+ break;
+
+ default:
+ debug("%s: Invalid input clock selection [%d]\n",
+ __func__, wm8994->sysclk[aif]);
+ return -1;
+ }
+
+ /* if input clock frequenct is more than 135Mhz then divide */
+ if (rate >= WM8994_MAX_INPUT_CLK_FREQ) {
+ rate /= 2;
+ reg1 |= WM8994_AIF1CLK_DIV;
+ }
+
+ wm8994->aifclk[aif] = rate;
+
+ ret = wm8994_update_bits(WM8994_AIF1_CLOCKING_1 + offset,
+ WM8994_AIF1CLK_SRC_MASK | WM8994_AIF1CLK_DIV,
+ reg1);
+
+ ret |= wm8994_update_bits(WM8994_CLOCKING_1,
+ WM8994_SYSCLK_SRC | WM8994_AIF2DSPCLK_ENA_MASK |
+ WM8994_SYSDSPCLK_ENA_MASK, WM8994_SYSCLK_SRC |
+ WM8994_AIF2DSPCLK_ENA | WM8994_SYSDSPCLK_ENA);
+
+ if (ret < 0) {
+ debug("%s: codec register access error\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Configures Audio interface for the given frequency
+ *
+ * @param wm8994 wm8994 information
+ * @param aif_id Audio Interface
+ * @param clk_id Input Clock ID
+ * @param freq Sampling frequency in Hz
+ *
+ * @return -1 for error and 0 success.
+ */
+static int wm8994_set_sysclk(struct wm8994_priv *wm8994, int aif_id,
+ int clk_id, unsigned int freq)
+{
+ int i;
+ int ret = 0;
+
+ wm8994->sysclk[aif_id - 1] = clk_id;
+
+ switch (clk_id) {
+ case WM8994_SYSCLK_MCLK1:
+ wm8994->mclk[0] = freq;
+ if (aif_id == 2) {
+ ret = wm8994_update_bits(WM8994_AIF1_CLOCKING_2 ,
+ WM8994_AIF2DAC_DIV_MASK , 0);
+ }
+ break;
+
+ case WM8994_SYSCLK_MCLK2:
+ /* TODO: Set GPIO AF */
+ wm8994->mclk[1] = freq;
+ break;
+
+ case WM8994_SYSCLK_FLL1:
+ case WM8994_SYSCLK_FLL2:
+ break;
+
+ case WM8994_SYSCLK_OPCLK:
+ /* Special case - a division (times 10) is given and
+ * no effect on main clocking.
+ */
+ if (freq) {
+ for (i = 0; i < ARRAY_SIZE(opclk_divs); i++)
+ if (opclk_divs[i] == freq)
+ break;
+ if (i == ARRAY_SIZE(opclk_divs))
+ return -1;
+ ret = wm8994_update_bits(WM8994_CLOCKING_2,
+ WM8994_OPCLK_DIV_MASK, i);
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_2,
+ WM8994_OPCLK_ENA, WM8994_OPCLK_ENA);
+ } else {
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_2,
+ WM8994_OPCLK_ENA, 0);
+ }
+
+ default:
+ debug("%s Invalid input clock selection [%d]\n",
+ __func__, clk_id);
+ return -1;
+ }
+
+ ret |= configure_aif_clock(wm8994, aif_id - 1);
+
+ if (ret < 0) {
+ debug("%s: codec register access error\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Initializes Volume for AIF2 to HP path
+ *
+ * @returns -1 for error and 0 Success.
+ *
+ */
+static int wm8994_init_volume_aif2_dac1(void)
+{
+ int ret;
+
+ /* Unmute AIF2DAC */
+ ret = wm8994_update_bits(WM8994_AIF2_DAC_FILTERS_1,
+ WM8994_AIF2DAC_MUTE_MASK, 0);
+
+
+ ret |= wm8994_update_bits(WM8994_AIF2_DAC_LEFT_VOLUME,
+ WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACL_VOL_MASK,
+ WM8994_AIF2DAC_VU | 0xff);
+
+ ret |= wm8994_update_bits(WM8994_AIF2_DAC_RIGHT_VOLUME,
+ WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACR_VOL_MASK,
+ WM8994_AIF2DAC_VU | 0xff);
+
+
+ ret |= wm8994_update_bits(WM8994_DAC1_LEFT_VOLUME,
+ WM8994_DAC1_VU_MASK | WM8994_DAC1L_VOL_MASK |
+ WM8994_DAC1L_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
+
+ ret |= wm8994_update_bits(WM8994_DAC1_RIGHT_VOLUME,
+ WM8994_DAC1_VU_MASK | WM8994_DAC1R_VOL_MASK |
+ WM8994_DAC1R_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
+ /* Head Phone Volume */
+ ret |= wm8994_i2c_write(WM8994_LEFT_OUTPUT_VOLUME, 0x12D);
+ ret |= wm8994_i2c_write(WM8994_RIGHT_OUTPUT_VOLUME, 0x12D);
+
+ if (ret < 0) {
+ debug("%s: codec register access error\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Intialise wm8994 codec device
+ *
+ * @param wm8994 wm8994 information
+ *
+ * @returns -1 for error and 0 Success.
+ */
+static int wm8994_device_init(struct wm8994_priv *wm8994)
+{
+ const char *devname;
+ unsigned short reg_data;
+ int ret;
+
+ wm8994_i2c_write(WM8994_SOFTWARE_RESET, WM8994_SW_RESET);/* Reset */
+
+ ret = wm8994_i2c_read(WM8994_SOFTWARE_RESET, ®_data);
+ if (ret < 0) {
+ debug("Failed to read ID register\n");
+ goto err;
+ }
+
+ if (reg_data == WM8994_ID) {
+ devname = "WM8994";
+ debug("Device registered as type %d\n", wm8994->type);
+ wm8994->type = WM8994;
+ } else {
+ debug("Device is not a WM8994, ID is %x\n", ret);
+ ret = -1;
+ goto err;
+ }
+
+ ret = wm8994_i2c_read(WM8994_CHIP_REVISION, ®_data);
+ if (ret < 0) {
+ debug("Failed to read revision register: %d\n", ret);
+ goto err;
+ }
+ wm8994->revision = reg_data;
+ debug("%s revision %c\n", devname, 'A' + wm8994->revision);
+
+ /* VMID Selection */
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
+ WM8994_VMID_SEL_MASK | WM8994_BIAS_ENA_MASK, 0x3);
+
+ /* Charge Pump Enable */
+ ret |= wm8994_update_bits(WM8994_CHARGE_PUMP_1, WM8994_CP_ENA_MASK,
+ WM8994_CP_ENA);
+
+ /* Head Phone Power Enable */
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
+ WM8994_HPOUT1L_ENA_MASK, WM8994_HPOUT1L_ENA);
+
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
+ WM8994_HPOUT1R_ENA_MASK, WM8994_HPOUT1R_ENA);
+
+ /* Power enable for AIF2 and DAC1 */
+ ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_5,
+ WM8994_AIF2DACL_ENA_MASK | WM8994_AIF2DACR_ENA_MASK |
+ WM8994_DAC1L_ENA_MASK | WM8994_DAC1R_ENA_MASK,
+ WM8994_AIF2DACL_ENA | WM8994_AIF2DACR_ENA | WM8994_DAC1L_ENA |
+ WM8994_DAC1R_ENA);
+
+ /* Head Phone Initialisation */
+ ret |= wm8994_update_bits(WM8994_ANALOGUE_HP_1,
+ WM8994_HPOUT1L_DLY_MASK | WM8994_HPOUT1R_DLY_MASK,
+ WM8994_HPOUT1L_DLY | WM8994_HPOUT1R_DLY);
+
+ ret |= wm8994_update_bits(WM8994_DC_SERVO_1,
+ WM8994_DCS_ENA_CHAN_0_MASK |
+ WM8994_DCS_ENA_CHAN_1_MASK , WM8994_DCS_ENA_CHAN_0 |
+ WM8994_DCS_ENA_CHAN_1);
+
+ ret |= wm8994_update_bits(WM8994_ANALOGUE_HP_1,
+ WM8994_HPOUT1L_DLY_MASK |
+ WM8994_HPOUT1R_DLY_MASK | WM8994_HPOUT1L_OUTP_MASK |
+ WM8994_HPOUT1R_OUTP_MASK |
+ WM8994_HPOUT1L_RMV_SHORT_MASK |
+ WM8994_HPOUT1R_RMV_SHORT_MASK, WM8994_HPOUT1L_DLY |
+ WM8994_HPOUT1R_DLY | WM8994_HPOUT1L_OUTP |
+ WM8994_HPOUT1R_OUTP | WM8994_HPOUT1L_RMV_SHORT |
+ WM8994_HPOUT1R_RMV_SHORT);
+
+ /* MIXER Config DAC1 to HP */
+ ret |= wm8994_update_bits(WM8994_OUTPUT_MIXER_1,
+ WM8994_DAC1L_TO_HPOUT1L_MASK, WM8994_DAC1L_TO_HPOUT1L);
+
+ ret |= wm8994_update_bits(WM8994_OUTPUT_MIXER_2,
+ WM8994_DAC1R_TO_HPOUT1R_MASK, WM8994_DAC1R_TO_HPOUT1R);
+
+ /* Routing AIF2 to DAC1 */
+ ret |= wm8994_update_bits(WM8994_DAC1_LEFT_MIXER_ROUTING,
+ WM8994_AIF2DACL_TO_DAC1L_MASK,
+ WM8994_AIF2DACL_TO_DAC1L);
+
+ ret |= wm8994_update_bits(WM8994_DAC1_RIGHT_MIXER_ROUTING,
+ WM8994_AIF2DACR_TO_DAC1R_MASK,
+ WM8994_AIF2DACR_TO_DAC1R);
+
+ /* GPIO Settings for AIF2 */
+ /* B CLK */
+ ret |= wm8994_update_bits(WM8994_GPIO_3, WM8994_GPIO_DIR_MASK |
+ WM8994_GPIO_FUNCTION_MASK ,
+ WM8994_GPIO_DIR_OUTPUT |
+ WM8994_GPIO_FUNCTION_I2S_CLK);
+
+ /* LR CLK */
+ ret |= wm8994_update_bits(WM8994_GPIO_4, WM8994_GPIO_DIR_MASK |
+ WM8994_GPIO_FUNCTION_MASK,
+ WM8994_GPIO_DIR_OUTPUT |
+ WM8994_GPIO_FUNCTION_I2S_CLK);
+
+ /* DATA */
+ ret |= wm8994_update_bits(WM8994_GPIO_5, WM8994_GPIO_DIR_MASK |
+ WM8994_GPIO_FUNCTION_MASK,
+ WM8994_GPIO_DIR_OUTPUT |
+ WM8994_GPIO_FUNCTION_I2S_CLK);
+
+ ret |= wm8994_init_volume_aif2_dac1();
+ if (ret < 0)
+ goto err;
+
+ debug("%s: Codec chip init ok\n", __func__);
+ return 0;
+err:
+ debug("%s: Codec chip init error\n", __func__);
+ return -1;
+}
+
+/*wm8994 Device Initialisation */
+int wm8994_init(struct sound_codec_info *pcodec_info,
+ enum en_audio_interface aif_id,
+ int sampling_rate, int mclk_freq,
+ int bits_per_sample, unsigned int channels)
+{
+ int ret = 0;
+
+ /* shift the device address by 1 for 7 bit addressing */
+ g_wm8994_i2c_dev_addr = pcodec_info->i2c_dev_addr >> 1;
+ wm8994_i2c_init(pcodec_info->i2c_bus);
+
+ if (pcodec_info->codec_type == CODEC_WM_8994)
+ g_wm8994_info.type = WM8994;
+ else {
+ debug("%s: Codec id [%d] not defined\n", __func__,
+ pcodec_info->codec_type);
+ return -1;
+ }
+
+ ret = wm8994_device_init(&g_wm8994_info);
+ if (ret < 0) {
+ debug("%s: wm8994 codec chip init failed\n", __func__);
+ return ret;
+ }
+
+ ret = wm8994_set_sysclk(&g_wm8994_info, aif_id, WM8994_SYSCLK_MCLK1,
+ mclk_freq);
+ if (ret < 0) {
+ debug("%s: wm8994 codec set sys clock failed\n", __func__);
+ return ret;
+ }
+
+ ret = wm8994_hw_params(&g_wm8994_info, aif_id, sampling_rate,
+ bits_per_sample, channels);
+
+ if (ret == 0) {
+ ret = wm8994_set_fmt(aif_id, SND_SOC_DAIFMT_I2S |
+ SND_SOC_DAIFMT_NB_NF |
+ SND_SOC_DAIFMT_CBS_CFS);
+ }
+ return ret;
+}
new file mode 100644
@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ * R. Chadrasekar <rcsekar@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __WM8994_H__
+#define __WM8994_H__
+
+/* Sources for AIF1/2 SYSCLK - use with set_dai_sysclk() */
+#define WM8994_SYSCLK_MCLK1 1
+#define WM8994_SYSCLK_MCLK2 2
+#define WM8994_SYSCLK_FLL1 3
+#define WM8994_SYSCLK_FLL2 4
+
+/* Avilable audi interface ports in wm8994 codec */
+enum en_audio_interface {
+ WM8994_AIF1 = 1,
+ WM8994_AIF2,
+ WM8994_AIF3
+};
+
+/* OPCLK is also configured with set_dai_sysclk, specify division*10 as rate. */
+#define WM8994_SYSCLK_OPCLK 5
+
+#define WM8994_FLL1 1
+#define WM8994_FLL2 2
+
+#define WM8994_FLL_SRC_MCLK1 1
+#define WM8994_FLL_SRC_MCLK2 2
+#define WM8994_FLL_SRC_LRCLK 3
+#define WM8994_FLL_SRC_BCLK 4
+
+/* maximum available digital interfac in the dac to configure */
+#define WM8994_MAX_AIF 2
+
+#define WM8994_MAX_INPUT_CLK_FREQ 13500000
+#define WM8994_ID 0x8994
+
+enum wm8994_vmid_mode {
+ WM8994_VMID_NORMAL,
+ WM8994_VMID_FORCE,
+};
+
+/* wm 8994 family devices */
+enum wm8994_type {
+ WM8994 = 0,
+ WM8958 = 1,
+ WM1811 = 2,
+};
+
+/*
+ * intialise wm8994 sound codec device for the given configuration
+ *
+ * @param pcodec_info pointer value of the sound codec info structure
+ * parsed from device tree
+ * @param aif_id enum value of codec interface port in which
+ * soc i2s is connected
+ * @param sampling_rate Sampling rate
+ * @param mclk_freq MCLK Frequency
+ * @param bits_per_sample bits per Sample
+ * @param channels Number of channnels
+ *
+ * @returns -1 for error and 0 Success.
+ */
+int wm8994_init(struct sound_codec_info *pcodec_info,
+ enum en_audio_interface aif_id,
+ int sampling_rate, int mclk_freq,
+ int bits_per_sample, unsigned int channels);
+#endif /*__WM8994_H__ */
new file mode 100644
@@ -0,0 +1,299 @@
+/*
+ * (C) Copyright 2012 Samsung Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MFD_WM8994_REGISTERS_H__
+#define __MFD_WM8994_REGISTERS_H__
+
+/*
+ * Register values.
+ */
+#define WM8994_SOFTWARE_RESET 0x00
+#define WM8994_POWER_MANAGEMENT_1 0x01
+#define WM8994_POWER_MANAGEMENT_2 0x02
+#define WM8994_POWER_MANAGEMENT_5 0x05
+#define WM8994_LEFT_OUTPUT_VOLUME 0x1C
+#define WM8994_RIGHT_OUTPUT_VOLUME 0x1D
+#define WM8994_OUTPUT_MIXER_1 0x2D
+#define WM8994_OUTPUT_MIXER_2 0x2E
+#define WM8994_CHARGE_PUMP_1 0x4C
+#define WM8994_DC_SERVO_1 0x54
+#define WM8994_ANALOGUE_HP_1 0x60
+#define WM8994_CHIP_REVISION 0x100
+#define WM8994_AIF1_CLOCKING_1 0x200
+#define WM8994_AIF1_CLOCKING_2 0x201
+#define WM8994_AIF2_CLOCKING_1 0x204
+#define WM8994_CLOCKING_1 0x208
+#define WM8994_CLOCKING_2 0x209
+#define WM8994_AIF1_RATE 0x210
+#define WM8994_AIF2_RATE 0x211
+#define WM8994_RATE_STATUS 0x212
+#define WM8994_AIF1_CONTROL_1 0x300
+#define WM8994_AIF1_CONTROL_2 0x301
+#define WM8994_AIF1_MASTER_SLAVE 0x302
+#define WM8994_AIF1_BCLK 0x303
+#define WM8994_AIF2_CONTROL_1 0x310
+#define WM8994_AIF2_CONTROL_2 0x311
+#define WM8994_AIF2_MASTER_SLAVE 0x312
+#define WM8994_AIF2_BCLK 0x313
+#define WM8994_AIF2_DAC_LEFT_VOLUME 0x502
+#define WM8994_AIF2_DAC_RIGHT_VOLUME 0x503
+#define WM8994_AIF2_DAC_FILTERS_1 0x520
+#define WM8994_DAC1_LEFT_MIXER_ROUTING 0x601
+#define WM8994_DAC1_RIGHT_MIXER_ROUTING 0x602
+#define WM8994_DAC1_LEFT_VOLUME 0x610
+#define WM8994_DAC1_RIGHT_VOLUME 0x611
+#define WM8994_GPIO_3 0x702
+#define WM8994_GPIO_4 0x703
+#define WM8994_GPIO_5 0x704
+
+/*
+ * Field Definitions.
+ */
+
+/*
+ * R0 (0x00) - Software Reset
+ */
+/* SW_RESET */
+#define WM8994_SW_RESET 1
+/*
+ * R1 (0x01) - Power Management (1)
+ */
+/* HPOUT1L_ENA */
+#define WM8994_HPOUT1L_ENA 0x0200
+/* HPOUT1L_ENA */
+#define WM8994_HPOUT1L_ENA_MASK 0x0200
+/* HPOUT1R_ENA */
+#define WM8994_HPOUT1R_ENA 0x0100
+/* HPOUT1R_ENA */
+#define WM8994_HPOUT1R_ENA_MASK 0x0100
+/* VMID_SEL - [2:1] */
+#define WM8994_VMID_SEL_MASK 0x0006
+/* BIAS_ENA */
+#define WM8994_BIAS_ENA 0x0001
+/* BIAS_ENA */
+#define WM8994_BIAS_ENA_MASK 0x0001
+
+/*
+ * R2 (0x02) - Power Management (2)
+ */
+/* OPCLK_ENA */
+#define WM8994_OPCLK_ENA 0x0800
+
+/*
+ * R5 (0x05) - Power Management (5)
+ */
+/* AIF2DACL_ENA */
+#define WM8994_AIF2DACL_ENA 0x2000
+#define WM8994_AIF2DACL_ENA_MASK 0x2000
+/* AIF2DACR_ENA */
+#define WM8994_AIF2DACR_ENA 0x1000
+#define WM8994_AIF2DACR_ENA_MASK 0x1000
+/* DAC1L_ENA */
+#define WM8994_DAC1L_ENA 0x0002
+#define WM8994_DAC1L_ENA_MASK 0x0002
+/* DAC1R_ENA */
+#define WM8994_DAC1R_ENA 0x0001
+#define WM8994_DAC1R_ENA_MASK 0x0001
+
+/*
+ * R45 (0x2D) - Output Mixer (1)
+ */
+/* DAC1L_TO_HPOUT1L */
+#define WM8994_DAC1L_TO_HPOUT1L 0x0100
+#define WM8994_DAC1L_TO_HPOUT1L_MASK 0x0100
+
+/*
+ * R46 (0x2E) - Output Mixer (2)
+ */
+/* DAC1R_TO_HPOUT1R */
+#define WM8994_DAC1R_TO_HPOUT1R 0x0100
+#define WM8994_DAC1R_TO_HPOUT1R_MASK 0x0100
+
+/*
+ * R76 (0x4C) - Charge Pump (1)
+ */
+/* CP_ENA */
+#define WM8994_CP_ENA 0x8000
+#define WM8994_CP_ENA_MASK 0x8000
+/*
+ * R84 (0x54) - DC Servo (1)
+ */
+/* DCS_ENA_CHAN_1 */
+#define WM8994_DCS_ENA_CHAN_1 0x0002
+#define WM8994_DCS_ENA_CHAN_1_MASK 0x0002
+/* DCS_ENA_CHAN_0 */
+#define WM8994_DCS_ENA_CHAN_0 0x0001
+#define WM8994_DCS_ENA_CHAN_0_MASK 0x0001
+
+/*
+ * R96 (0x60) - Analogue HP (1)
+ */
+/* HPOUT1L_RMV_SHORT */
+#define WM8994_HPOUT1L_RMV_SHORT 0x0080
+#define WM8994_HPOUT1L_RMV_SHORT_MASK 0x0080
+/* HPOUT1L_OUTP */
+#define WM8994_HPOUT1L_OUTP 0x0040
+#define WM8994_HPOUT1L_OUTP_MASK 0x0040
+/* HPOUT1L_DLY */
+#define WM8994_HPOUT1L_DLY 0x0020
+#define WM8994_HPOUT1L_DLY_MASK 0x0020
+/* HPOUT1R_RMV_SHORT */
+#define WM8994_HPOUT1R_RMV_SHORT 0x0008
+#define WM8994_HPOUT1R_RMV_SHORT_MASK 0x0008
+/* HPOUT1R_OUTP */
+#define WM8994_HPOUT1R_OUTP 0x0004
+#define WM8994_HPOUT1R_OUTP_MASK 0x0004
+/* HPOUT1R_DLY */
+#define WM8994_HPOUT1R_DLY 0x0002
+#define WM8994_HPOUT1R_DLY_MASK 0x0002
+
+/*
+ * R512 (0x200) - AIF1 Clocking (1)
+ */
+/* AIF1CLK_SRC - [4:3] */
+#define WM8994_AIF1CLK_SRC_MASK 0x0018
+/* AIF1CLK_DIV */
+#define WM8994_AIF1CLK_DIV 0x0002
+/* AIF1CLK_ENA */
+#define WM8994_AIF1CLK_ENA 0x0001
+#define WM8994_AIF1CLK_ENA_MASK 0x0001
+
+/*
+ * R517 (0x205) - AIF2 Clocking (2)
+ */
+/* AIF2DAC_DIV - [5:3] */
+#define WM8994_AIF2DAC_DIV_MASK 0x0038
+
+/*
+ * R520 (0x208) - Clocking (1)
+ */
+/* AIF2DSPCLK_ENA */
+#define WM8994_AIF2DSPCLK_ENA 0x0004
+#define WM8994_AIF2DSPCLK_ENA_MASK 0x0004
+/* SYSDSPCLK_ENA */
+#define WM8994_SYSDSPCLK_ENA 0x0002
+#define WM8994_SYSDSPCLK_ENA_MASK 0x0002
+/* SYSCLK_SRC */
+#define WM8994_SYSCLK_SRC 0x0001
+
+/*
+ * R521 (0x209) - Clocking (2)
+ */
+/* OPCLK_DIV - [2:0] */
+#define WM8994_OPCLK_DIV_MASK 0x0007
+
+/*
+ * R528 (0x210) - AIF1 Rate
+ */
+/* AIF1_SR - [7:4] */
+#define WM8994_AIF1_SR_MASK 0x00F0
+#define WM8994_AIF1_SR_SHIFT 4
+/* AIF1CLK_RATE - [3:0] */
+#define WM8994_AIF1CLK_RATE_MASK 0x000F
+
+/*
+ * R768 (0x300) - AIF1 Control (1)
+ */
+/* AIF1_BCLK_INV */
+#define WM8994_AIF1_BCLK_INV 0x0100
+/* AIF1_LRCLK_INV */
+#define WM8994_AIF1_LRCLK_INV 0x0080
+#define WM8994_AIF1_LRCLK_INV_MASK 0x0080
+/* AIF1_WL - [6:5] */
+#define WM8994_AIF1_WL_MASK 0x0060
+/* AIF1_FMT - [4:3] */
+#define WM8994_AIF1_FMT_MASK 0x0018
+
+/*
+ * R769 (0x301) - AIF1 Control (2)
+ */
+/* AIF1_MONO */
+#define WM8994_AIF1_MONO 0x0100
+
+/*
+ * R770 (0x302) - AIF1 Master/Slave
+ */
+/* AIF1_MSTR */
+#define WM8994_AIF1_MSTR 0x4000
+#define WM8994_AIF1_MSTR_MASK 0x4000
+
+/*
+ * R771 (0x303) - AIF1 BCLK
+ */
+/* AIF1_BCLK_DIV - [8:4] */
+#define WM8994_AIF1_BCLK_DIV_MASK 0x01F0
+#define WM8994_AIF1_BCLK_DIV_SHIFT 4
+
+/*
+ * R1282 (0x502) - AIF2 DAC Left Volume
+ */
+/* AIF2DAC_VU */
+#define WM8994_AIF2DAC_VU 0x0100
+#define WM8994_AIF2DAC_VU_MASK 0x0100
+/* AIF2DACL_VOL - [7:0] */
+#define WM8994_AIF2DACL_VOL_MASK 0x00FF
+
+/*
+ * R1283 (0x503) - AIF2 DAC Right Volume
+ */
+/* AIF2DACR_VOL - [7:0] */
+#define WM8994_AIF2DACR_VOL_MASK 0x00FF
+
+/*
+ * R1312 (0x520) - AIF2 DAC Filters (1)
+ */
+/* AIF2DAC_MUTE */
+#define WM8994_AIF2DAC_MUTE_MASK 0x0200
+
+/*
+ * R1537 (0x601) - DAC1 Left Mixer Routing
+ */
+/* AIF2DACL_TO_DAC1L */
+#define WM8994_AIF2DACL_TO_DAC1L 0x0004
+#define WM8994_AIF2DACL_TO_DAC1L_MASK 0x0004
+
+/*
+ * R1538 (0x602) - DAC1 Right Mixer Routing
+ */
+/* AIF2DACR_TO_DAC1R */
+#define WM8994_AIF2DACR_TO_DAC1R 0x0004
+#define WM8994_AIF2DACR_TO_DAC1R_MASK 0x0004
+
+/*
+ * R1552 (0x610) - DAC1 Left Volume
+ */
+/* DAC1L_MUTE */
+#define WM8994_DAC1L_MUTE_MASK 0x0200
+/* DAC1_VU */
+#define WM8994_DAC1_VU 0x0100
+#define WM8994_DAC1_VU_MASK 0x0100
+/* DAC1L_VOL - [7:0] */
+#define WM8994_DAC1L_VOL_MASK 0x00FF
+
+/*
+ * R1553 (0x611) - DAC1 Right Volume
+ */
+/* DAC1R_MUTE */
+#define WM8994_DAC1R_MUTE_MASK 0x0200
+/* DAC1R_VOL - [7:0] */
+#define WM8994_DAC1R_VOL_MASK 0x00FF
+
+/*
+ * GPIO
+ */
+/* OUTPUT PIN */
+#define WM8994_GPIO_DIR_OUTPUT 0x8000
+/* GPIO PIN MASK */
+#define WM8994_GPIO_DIR_MASK 0xFFE0
+/* I2S CLK */
+#define WM8994_GPIO_FUNCTION_I2S_CLK 0x0000
+/* GPn FN */
+#define WM8994_GPIO_FUNCTION_MASK 0x001F
+#endif