[V2,09/13] thermal/drivers/hisi: Remove costly sensor inspection

Message ID 1504554972-2624-9-git-send-email-daniel.lezcano@linaro.org
State Superseded
Headers show
Series
  • Untitled series #3764
Related show

Commit Message

Daniel Lezcano Sept. 4, 2017, 7:56 p.m.
The sensor is all setup, bind, resetted, acked, etc... every single second.

That was the way to workaround a problem with the interrupt bouncing again and
again.

With the following changes, we fix all in one:

 - Do the setup, one time, at probe time

 - Add the IRQF_ONESHOT, ack the interrupt in the threaded handler

 - Remove the interrupt handler

 - Set the correct value for the LAG register

 - Remove all the irq_enabled stuff in the code as the interruption
   handling is fixed

 - Remove the 3ms delay

 - Reorder the initialization routine to be in the right order

It ends up to a nicer code and more efficient, the 3-5ms delay is removed from
the get_temp() path.

Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

Reviewed-by: Leo Yan <leo.yan@linaro.org>

Tested-by: Leo Yan <leo.yan@linaro.org>

---
 drivers/thermal/hisi_thermal.c | 203 +++++++++++++++++++----------------------
 1 file changed, 93 insertions(+), 110 deletions(-)

-- 
2.7.4

Patch

diff --git a/drivers/thermal/hisi_thermal.c b/drivers/thermal/hisi_thermal.c
index 10ef6bc..3ce9a4f 100644
--- a/drivers/thermal/hisi_thermal.c
+++ b/drivers/thermal/hisi_thermal.c
@@ -41,6 +41,7 @@ 
 #define HISI_TEMP_BASE			(-60000)
 #define HISI_TEMP_RESET			(100000)
 #define HISI_TEMP_STEP			(784)
+#define HISI_TEMP_LAG			(3500)
 
 #define HISI_MAX_SENSORS		4
 #define HISI_DEFAULT_SENSOR		2
@@ -60,8 +61,6 @@  struct hisi_thermal_data {
 	struct clk *clk;
 	struct hisi_thermal_sensor sensors;
 	int irq;
-	bool irq_enabled;
-
 	void __iomem *regs;
 };
 
@@ -99,9 +98,40 @@  static inline long hisi_thermal_round_temp(int temp)
 		hisi_thermal_temp_to_step(temp));
 }
 
+/*
+ * The lag register contains 5 bits encoding the temperature in steps.
+ *
+ * Each time the temperature crosses the threshold boundary, an
+ * interrupt is raised. It could be when the temperature is going
+ * above the threshold or below. However, if the temperature is
+ * fluctuating around this value due to the load, we can receive
+ * several interrupts which may not desired.
+ *
+ * We can setup a temperature representing the delta between the
+ * threshold and the current temperature when the temperature is
+ * decreasing.
+ *
+ * For instance: the lag register is 5°C, the threshold is 65°C, when
+ * the temperature reaches 65°C an interrupt is raised and when the
+ * temperature decrease to 65°C - 5°C another interrupt is raised.
+ *
+ * A very short lag can lead to an interrupt storm, a long lag
+ * increase the latency to react to the temperature changes.  In our
+ * case, that is not really a problem as we are polling the
+ * temperature.
+ *
+ * [0:4] : lag register
+ *
+ * The temperature is coded in steps, cf. HISI_TEMP_STEP.
+ *
+ * Min : 0x00 :  0.0 °C
+ * Max : 0x1F : 24.3 °C
+ *
+ * The 'value' parameter is in milliCelsius.
+ */
 static inline void hisi_thermal_set_lag(void __iomem *addr, int value)
 {
-	writel(value, addr + TEMP0_LAG);
+	writel((value / HISI_TEMP_STEP) & 0x1F, addr + TEMP0_LAG);
 }
 
 static inline void hisi_thermal_alarm_clear(void __iomem *addr, int value)
@@ -171,71 +201,6 @@  static inline void hisi_thermal_hdak_set(void __iomem *addr, int value)
 	       (value << 4), addr + TEMP0_CFG);
 }
 
-static long hisi_thermal_get_sensor_temp(struct hisi_thermal_data *data,
-					 struct hisi_thermal_sensor *sensor)
-{
-	long val;
-
-	mutex_lock(&data->thermal_lock);
-
-	/* disable interrupt */
-	hisi_thermal_alarm_enable(data->regs, 0);
-	hisi_thermal_alarm_clear(data->regs, 1);
-
-	/* disable module firstly */
-	hisi_thermal_enable(data->regs, 0);
-
-	/* select sensor id */
-	hisi_thermal_sensor_select(data->regs, sensor->id);
-
-	/* enable module */
-	hisi_thermal_enable(data->regs, 1);
-
-	usleep_range(3000, 5000);
-
-	val = hisi_thermal_get_temperature(data->regs);
-
-	mutex_unlock(&data->thermal_lock);
-
-	return val;
-}
-
-static void hisi_thermal_enable_bind_irq_sensor
-			(struct hisi_thermal_data *data)
-{
-	struct hisi_thermal_sensor *sensor;
-
-	mutex_lock(&data->thermal_lock);
-
-	sensor = &data->sensors;
-
-	/* setting the hdak time */
-	hisi_thermal_hdak_set(data->regs, 0);
-
-	/* disable module firstly */
-	hisi_thermal_reset_enable(data->regs, 0);
-	hisi_thermal_enable(data->regs, 0);
-
-	/* select sensor id */
-	hisi_thermal_sensor_select(data->regs, sensor->id);
-
-	/* enable for interrupt */
-	hisi_thermal_alarm_set(data->regs, sensor->thres_temp);
-
-	hisi_thermal_reset_set(data->regs, HISI_TEMP_RESET);
-
-	/* enable module */
-	hisi_thermal_reset_enable(data->regs, 1);
-	hisi_thermal_enable(data->regs, 1);
-
-	hisi_thermal_alarm_clear(data->regs, 0);
-	hisi_thermal_alarm_enable(data->regs, 1);
-
-	usleep_range(3000, 5000);
-
-	mutex_unlock(&data->thermal_lock);
-}
-
 static void hisi_thermal_disable_sensor(struct hisi_thermal_data *data)
 {
 	mutex_lock(&data->thermal_lock);
@@ -253,25 +218,10 @@  static int hisi_thermal_get_temp(void *_sensor, int *temp)
 	struct hisi_thermal_sensor *sensor = _sensor;
 	struct hisi_thermal_data *data = sensor->thermal;
 
-	*temp = hisi_thermal_get_sensor_temp(data, sensor);
-
-	dev_dbg(&data->pdev->dev, "id=%d, irq=%d, temp=%d, thres=%d\n",
-		sensor->id, data->irq_enabled, *temp, sensor->thres_temp);
-	/*
-	 * Bind irq to sensor for two cases:
-	 *   Reenable alarm IRQ if temperature below threshold;
-	 *   if irq has been enabled, always set it;
-	 */
-	if (data->irq_enabled) {
-		hisi_thermal_enable_bind_irq_sensor(data);
-		return 0;
-	}
+	*temp = hisi_thermal_get_temperature(data->regs);
 
-	if (*temp < sensor->thres_temp) {
-		data->irq_enabled = true;
-		hisi_thermal_enable_bind_irq_sensor(data);
-		enable_irq(data->irq);
-	}
+	dev_dbg(&data->pdev->dev, "id=%d, temp=%d, thres=%d\n",
+		sensor->id, *temp, sensor->thres_temp);
 
 	return 0;
 }
@@ -280,26 +230,27 @@  static const struct thermal_zone_of_device_ops hisi_of_thermal_ops = {
 	.get_temp = hisi_thermal_get_temp,
 };
 
-static irqreturn_t hisi_thermal_alarm_irq(int irq, void *dev)
+static irqreturn_t hisi_thermal_alarm_irq_thread(int irq, void *dev)
 {
 	struct hisi_thermal_data *data = dev;
+	struct hisi_thermal_sensor *sensor = &data->sensors;
+	int temp;
 
-	disable_irq_nosync(irq);
-	data->irq_enabled = false;
+	hisi_thermal_alarm_clear(data->regs, 1);
 
-	return IRQ_WAKE_THREAD;
-}
+	temp = hisi_thermal_get_temperature(data->regs);
 
-static irqreturn_t hisi_thermal_alarm_irq_thread(int irq, void *dev)
-{
-	struct hisi_thermal_data *data = dev;
-	struct hisi_thermal_sensor *sensor = &data->sensors;
+	if (temp >= sensor->thres_temp) {
+		dev_crit(&data->pdev->dev, "THERMAL ALARM: %d > %d\n",
+			 temp, sensor->thres_temp);
 
-	dev_crit(&data->pdev->dev, "THERMAL ALARM: T > %d\n",
-		 sensor->thres_temp);
+		thermal_zone_device_update(data->sensors.tzd,
+					   THERMAL_EVENT_UNSPECIFIED);
 
-	thermal_zone_device_update(data->sensors.tzd,
-				   THERMAL_EVENT_UNSPECIFIED);
+	} else if (temp < sensor->thres_temp) {
+		dev_crit(&data->pdev->dev, "THERMAL ALARM stopped: %d < %d\n",
+			 temp, sensor->thres_temp);
+	}
 
 	return IRQ_HANDLED;
 }
@@ -352,6 +303,40 @@  static void hisi_thermal_toggle_sensor(struct hisi_thermal_sensor *sensor,
 		on ? THERMAL_DEVICE_ENABLED : THERMAL_DEVICE_DISABLED);
 }
 
+static int hisi_thermal_setup(struct hisi_thermal_data *data)
+{
+	struct hisi_thermal_sensor *sensor;
+
+	sensor = &data->sensors;
+
+	/* disable module firstly */
+	hisi_thermal_reset_enable(data->regs, 0);
+	hisi_thermal_enable(data->regs, 0);
+
+	/* select sensor id */
+	hisi_thermal_sensor_select(data->regs, sensor->id);
+
+	/* setting the hdak time */
+	hisi_thermal_hdak_set(data->regs, 0);
+
+	/* setting lag value between current temp and the threshold */
+	hisi_thermal_set_lag(data->regs, HISI_TEMP_LAG);
+
+	/* enable for interrupt */
+	hisi_thermal_alarm_set(data->regs, sensor->thres_temp);
+
+	hisi_thermal_reset_set(data->regs, HISI_TEMP_RESET);
+
+	/* enable module */
+	hisi_thermal_reset_enable(data->regs, 1);
+	hisi_thermal_enable(data->regs, 1);
+
+	hisi_thermal_alarm_clear(data->regs, 0);
+	hisi_thermal_alarm_enable(data->regs, 1);
+
+	return 0;
+}
+
 static int hisi_thermal_probe(struct platform_device *pdev)
 {
 	struct hisi_thermal_data *data;
@@ -394,9 +379,6 @@  static int hisi_thermal_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	hisi_thermal_enable_bind_irq_sensor(data);
-	data->irq_enabled = true;
-
 	ret = hisi_thermal_register_sensor(pdev, data,
 					   &data->sensors,
 					   HISI_DEFAULT_SENSOR);
@@ -406,18 +388,21 @@  static int hisi_thermal_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	hisi_thermal_toggle_sensor(&data->sensors, true);
+	ret = hisi_thermal_setup(data);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to setup the sensor: %d\n", ret);
+		return ret;
+	}
 
-	ret = devm_request_threaded_irq(&pdev->dev, data->irq,
-					hisi_thermal_alarm_irq,
+	ret = devm_request_threaded_irq(&pdev->dev, data->irq, NULL,
 					hisi_thermal_alarm_irq_thread,
-					0, "hisi_thermal", data);
+					IRQF_ONESHOT, "hisi_thermal", data);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
 		return ret;
 	}
 
-	enable_irq(data->irq);
+	hisi_thermal_toggle_sensor(&data->sensors, true);
 
 	return 0;
 }
@@ -440,7 +425,6 @@  static int hisi_thermal_suspend(struct device *dev)
 	struct hisi_thermal_data *data = dev_get_drvdata(dev);
 
 	hisi_thermal_disable_sensor(data);
-	data->irq_enabled = false;
 
 	clk_disable_unprepare(data->clk);
 
@@ -456,8 +440,7 @@  static int hisi_thermal_resume(struct device *dev)
 	if (ret)
 		return ret;
 
-	data->irq_enabled = true;
-	hisi_thermal_enable_bind_irq_sensor(data);
+	hisi_thermal_setup(data);
 
 	return 0;
 }