| Message ID | 1507854928-4357-2-git-send-email-hayashi.kunihiko@socionext.com |
|---|---|
| State | New |
| Headers | show |
| Series | [net-next,v2,1/2] dt-bindings: net: add DT bindings for Socionext UniPhier AVE | expand |
2017-10-13 9:35 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>: > DT bindings for the AVE ethernet controller found on Socionext's > UniPhier platforms. > > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> > Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> > --- > .../bindings/net/socionext,uniphier-ave4.txt | 53 ++++++++++++++++++++++ > 1 file changed, 53 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt > > diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt > new file mode 100644 > index 0000000..25f4d92 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt > @@ -0,0 +1,53 @@ > +* Socionext AVE ethernet controller > + > +This describes the devicetree bindings for AVE ethernet controller > +implemented on Socionext UniPhier SoCs. > + > +Required properties: > + - compatible: Should be > + - "socionext,uniphier-pro4-ave4" : for Pro4 SoC > + - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC > + - "socionext,uniphier-ld20-ave4" : for LD20 SoC > + - "socionext,uniphier-ld11-ave4" : for LD11 SoC > + - reg: Address where registers are mapped and size of region. > + - interrupts: Should contain the MAC interrupt. > + - phy-mode: See ethernet.txt in the same directory. Allow to choose > + "rgmii", "rmii", or "mii" according to the PHY. > + - pinctrl-names: List of assigned state names, see pinctrl > + binding documentation. > + - pinctrl-0: List of phandles to configure the GPIO pin, > + see pinctrl binding documentation. Choose this appropriately > + according to phy-mode. > + - <&pinctrl_ether_rgmii> if phy-mode is "rgmii". > + - <&pinctrl_ether_rmii> if phy-mode is "rmii". > + - <&pinctrl_ether_mii> if phy-mode is "mii". > + - phy-handle: Should point to the external phy device. > + See ethernet.txt file in the same directory. > + - mdio subnode: Should be device tree subnode with the following required > + properties: > + - #address-cells: Must be <1>. > + - #size-cells: Must be <0>. > + - reg: phy ID number, usually a small integer. > + > +Optional properties: > + - local-mac-address: See ethernet.txt in the same directory. > + > +Example: > + > + ether: ethernet@65000000 { > + compatible = "socionext,uniphier-ld20-ave4"; > + reg = <0x65000000 0x8500>; > + interrupts = <0 66 4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ether_rgmii>; > + phy-mode = "rgmii"; > + phy-handle = <ðphy>; > + local-mac-address = [00 00 00 00 00 00]; > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + ethphy: ethphy@1 { > + reg = <1>; > + }; > + }; > + }; > -- > 2.7.4 > I found the following code in 2/2. + /* get clock */ + priv->clk = clk_get(dev, NULL); + if (IS_ERR(priv->clk)) + priv->clk = NULL; + + /* get reset */ + priv->rst = reset_control_get(dev, NULL); + if (IS_ERR(priv->rst)) + priv->rst = NULL; + This doc needs to describe "clocks", "resets". -- Best Regards Masahiro Yamada
diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt new file mode 100644 index 0000000..25f4d92 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt @@ -0,0 +1,53 @@ +* Socionext AVE ethernet controller + +This describes the devicetree bindings for AVE ethernet controller +implemented on Socionext UniPhier SoCs. + +Required properties: + - compatible: Should be + - "socionext,uniphier-pro4-ave4" : for Pro4 SoC + - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC + - "socionext,uniphier-ld20-ave4" : for LD20 SoC + - "socionext,uniphier-ld11-ave4" : for LD11 SoC + - reg: Address where registers are mapped and size of region. + - interrupts: Should contain the MAC interrupt. + - phy-mode: See ethernet.txt in the same directory. Allow to choose + "rgmii", "rmii", or "mii" according to the PHY. + - pinctrl-names: List of assigned state names, see pinctrl + binding documentation. + - pinctrl-0: List of phandles to configure the GPIO pin, + see pinctrl binding documentation. Choose this appropriately + according to phy-mode. + - <&pinctrl_ether_rgmii> if phy-mode is "rgmii". + - <&pinctrl_ether_rmii> if phy-mode is "rmii". + - <&pinctrl_ether_mii> if phy-mode is "mii". + - phy-handle: Should point to the external phy device. + See ethernet.txt file in the same directory. + - mdio subnode: Should be device tree subnode with the following required + properties: + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + - reg: phy ID number, usually a small integer. + +Optional properties: + - local-mac-address: See ethernet.txt in the same directory. + +Example: + + ether: ethernet@65000000 { + compatible = "socionext,uniphier-ld20-ave4"; + reg = <0x65000000 0x8500>; + interrupts = <0 66 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ether_rgmii>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + local-mac-address = [00 00 00 00 00 00]; + mdio { + #address-cells = <1>; + #size-cells = <0>; + ethphy: ethphy@1 { + reg = <1>; + }; + }; + };