@@ -23,4 +23,10 @@ config DEBUG_PINMUX
help
Say Y here to add some extra checks and diagnostics to PINMUX calls.
+config PINMUX_U300
+ bool "U300 pinmux driver"
+ depends on ARCH_U300
+ help
+ Say Y here to enable the U300 pinmux driver
+
endif
@@ -3,3 +3,4 @@
ccflags-$(CONFIG_DEBUG_PINMUX) += -DDEBUG
obj-$(CONFIG_PINMUX) += core.o
+obj-$(CONFIG_PINMUX_U300) += pinmux-u300.o
new file mode 100644
@@ -0,0 +1,361 @@
+/*
+ * Driver for the U300 pinmux
+ *
+ * Based on the original U300 padmux functions
+ * Copyright (C) 2009 ST-Ericsson AB
+ * Author: Martin Persson <martin.persson@stericsson.com>
+ *
+ * The DB3350 design and control registers are oriented around pads rather than
+ * pins, so we enumerate the pads we can mux rather than actual pins. The pads
+ * are connected to different pins in different packaging types, so it would
+ * be confusing.
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/pinmux.h>
+
+#include "pinmux-u300.h"
+
+#define DRIVER_NAME "pinmux-u300"
+
+/*
+ * The DB3350 has 467 pads, I have enumerated the pads clockwise around the
+ * edges of the silicon, finger by finger. LTCORNER upper left is pad 0.
+ * Data taken from the PadRing chart, arranged like this:
+ *
+ * 0 ..... 104
+ * 466 105
+ * . .
+ * . .
+ * 358 224
+ * 357 .... 225
+ */
+#define U300_NUM_PADS 467
+
+struct u300_pin_desc {
+ unsigned number;
+ char *name;
+};
+
+#define U300_PIN(a, b) { .number = a, .name = b }
+
+const struct u300_pin_desc u300_pins[] = {
+ U300_PIN(134, "UART0 RTS"),
+ U300_PIN(135, "UART0 CTS"),
+ U300_PIN(136, "UART0 TX"),
+ U300_PIN(137, "UART0 RX"),
+ U300_PIN(166, "MMC DATA DIR LS"),
+ U300_PIN(167, "MMC DATA 3"),
+ U300_PIN(168, "MMC DATA 2"),
+ U300_PIN(169, "MMC DATA 1"),
+ U300_PIN(170, "MMC DATA 0"),
+ U300_PIN(171, "MMC CMD DIR LS"),
+ U300_PIN(176, "MMC CMD"),
+ U300_PIN(177, "MMC CLK"),
+ U300_PIN(420, "SPI CLK"),
+ U300_PIN(421, "SPI DO"),
+ U300_PIN(422, "SPI DI"),
+ U300_PIN(423, "SPI CS0"),
+ U300_PIN(424, "SPI CS1"),
+ U300_PIN(425, "SPI CS2"),
+};
+
+/**
+ * @dev: a pointer back to containing device
+ * @virtbase: the offset to the controller in virtual memory
+ */
+struct u300_pmx {
+ struct device *dev;
+ struct pinmux_dev *pmx;
+ u32 phybase;
+ u32 physize;
+ void __iomem *virtbase;
+};
+
+/**
+ * u300_pmx_registers - the array of registers read/written for each pinmux
+ * shunt setting
+ */
+const u32 u300_pmx_registers[] = {
+ U300_SYSCON_PMC1LR,
+ U300_SYSCON_PMC1HR,
+ U300_SYSCON_PMC2R,
+ U300_SYSCON_PMC3R,
+ U300_SYSCON_PMC4R,
+};
+
+/**
+ * struct pmx_onmask - mask bits to enable/disable padmux
+ * @mask: mask bits to disable
+ * @val: mask bits to enable
+ *
+ * onmask lazy dog:
+ * onmask = {
+ * {"PMC1LR" mask, "PMC1LR" value},
+ * {"PMC1HR" mask, "PMC1HR" value},
+ * {"PMC2R" mask, "PMC2R" value},
+ * {"PMC3R" mask, "PMC3R" value},
+ * {"PMC4R" mask, "PMC4R" value}
+ * }
+ */
+struct u300_pmx_mask {
+ u16 mask;
+ u16 bits;
+};
+
+/**
+ * struct u300_pmx_func - describes an U300 pinmux function
+ * @name: the name of this specific function
+ * @pins: an array of discrete physical pins used in this mapping, taken
+ * from the global pin enumeration space
+ * @num_pins: the number of pins in this mapping array, i.e. the number of
+ * elements in .pins so we can iterate over that array
+ * @onmask: bits to set to enable this muxing
+ */
+struct u300_pmx_func {
+ char *name;
+ const unsigned int *pins;
+ const unsigned num_pins;
+ const struct u300_pmx_mask *mask;
+};
+
+static const unsigned mmc0_pins[] = { 166, 167, 168, 169, 170, 171, 176, 177 };
+static const unsigned spi0_pins[] = { 420, 421, 422, 423, 424, 425 };
+
+static const struct u300_pmx_mask mmc0_mask[] = {
+ {U300_SYSCON_PMC1LR_MMCSD_MASK,
+ U300_SYSCON_PMC1LR_MMCSD_MMCSD},
+ {0, 0},
+ {0, 0},
+ {0, 0},
+ {U300_SYSCON_PMC4R_APP_MISC_12_MASK,
+ U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO}
+};
+
+static const struct u300_pmx_mask spi0_mask[] = {
+ {0, 0},
+ {U300_SYSCON_PMC1HR_APP_SPI_2_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK,
+ U300_SYSCON_PMC1HR_APP_SPI_2_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI},
+ {0, 0},
+ {0, 0},
+ {0, 0}
+};
+
+static const struct u300_pmx_func u300_pmx_funcs[] = {
+ {
+ .name = "mmc0",
+ .pins = mmc0_pins,
+ .num_pins = ARRAY_SIZE(mmc0_pins),
+ .mask = mmc0_mask,
+ },
+ {
+ .name = "spi0",
+ .pins = spi0_pins,
+ .num_pins = ARRAY_SIZE(spi0_pins),
+ .mask = spi0_mask,
+ },
+};
+
+static void u300_pmx_endisable(struct u300_pmx *upmx, unsigned selector,
+ bool enable)
+{
+ u16 regval, val, mask;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(u300_pmx_registers); i++) {
+ if (enable)
+ val = u300_pmx_funcs[selector].mask->bits;
+ else
+ val = 0;
+
+ mask = u300_pmx_funcs[selector].mask->mask;
+ if (mask != 0) {
+ regval = readw(upmx->virtbase + u300_pmx_registers[i]);
+ regval &= ~mask;
+ regval |= val;
+ writew(regval, upmx->virtbase + u300_pmx_registers[i]);
+ }
+ }
+}
+
+static int u300_pmx_enable(struct pinmux_dev *pmxdev, unsigned selector)
+{
+ struct u300_pmx *upmx;
+
+ if (selector >= ARRAY_SIZE(u300_pmx_funcs))
+ return -EINVAL;
+ upmx = pmxdev_get_drvdata(pmxdev);
+ u300_pmx_endisable(upmx, selector, true);
+
+ return 0;
+}
+
+static void u300_pmx_disable(struct pinmux_dev *pmxdev, unsigned selector)
+{
+ struct u300_pmx *upmx;
+
+ if (selector >= ARRAY_SIZE(u300_pmx_funcs))
+ return;
+ upmx = pmxdev_get_drvdata(pmxdev);
+ u300_pmx_endisable(upmx, selector, false);
+}
+
+static int u300_pmx_list(struct pinmux_dev *pmxdev, unsigned selector)
+{
+ if (selector >= ARRAY_SIZE(u300_pmx_funcs))
+ return -EINVAL;
+ return 0;
+}
+
+static const char *u300_pmx_get_fname(struct pinmux_dev *pmxdev,
+ unsigned selector)
+{
+ if (selector >= ARRAY_SIZE(u300_pmx_funcs))
+ return NULL;
+ return u300_pmx_funcs[selector].name;
+}
+
+static int u300_pmx_get_pins(struct pinmux_dev *pmxdev, unsigned selector,
+ unsigned ** const pins, unsigned * const num_pins)
+{
+ if (selector >= ARRAY_SIZE(u300_pmx_funcs))
+ return -EINVAL;
+ *pins = (unsigned *) u300_pmx_funcs[selector].pins;
+ *num_pins = u300_pmx_funcs[selector].num_pins;
+ return 0;
+}
+
+static void u300_dbg_show(struct pinmux_dev *pmxdev, struct seq_file *s,
+ unsigned offset)
+{
+ int i;
+
+ seq_printf(s, " " DRIVER_NAME);
+ seq_printf(s, " :");
+ for (i = 0; i < ARRAY_SIZE(u300_pins); i++) {
+ if (u300_pins[i].number == offset) {
+ seq_printf(s, " %s", u300_pins[i].name);
+ break;
+ }
+ }
+ if (i == ARRAY_SIZE(u300_pins))
+ seq_printf(s, " (unknown function)");
+}
+
+static struct pinmux_ops u300_pmx_ops = {
+ .list_functions = u300_pmx_list,
+ .get_function_name = u300_pmx_get_fname,
+ .get_function_pins = u300_pmx_get_pins,
+ .enable = u300_pmx_enable,
+ .disable = u300_pmx_disable,
+ .dbg_show = u300_dbg_show,
+};
+
+static struct pinmux_desc u300_pmx_desc = {
+ .name = DRIVER_NAME,
+ .ops = &u300_pmx_ops,
+ .owner = THIS_MODULE,
+ .base = 0,
+ .npins = U300_NUM_PADS,
+};
+
+static int __init u300_pmx_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct u300_pmx *upmx;
+ struct resource *res;
+
+ upmx = kzalloc(sizeof(struct u300_pmx), GFP_KERNEL);
+ if (!upmx)
+ return -ENOMEM;
+
+ upmx->dev = &pdev->dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ ret = -ENOENT;
+ goto out_no_resource;
+ }
+ upmx->phybase = res->start;
+ upmx->physize = resource_size(res);
+
+ if (request_mem_region(upmx->phybase, upmx->physize,
+ DRIVER_NAME) == NULL) {
+ ret = -EBUSY;
+ goto out_no_memregion;
+ }
+
+ upmx->virtbase = ioremap(upmx->phybase, upmx->physize);
+ if (!upmx->virtbase) {
+ ret = -ENOMEM;
+ goto out_no_remap;
+ }
+
+ upmx->pmx = pinmux_register(&u300_pmx_desc, &pdev->dev, upmx);
+ if (IS_ERR(upmx->pmx)) {
+ ret = PTR_ERR(upmx->pmx);
+ goto out_no_pmx;
+ }
+ platform_set_drvdata(pdev, upmx);
+
+ dev_info(&pdev->dev, "initialized U300 pinmux driver\n");
+
+ return 0;
+
+out_no_pmx:
+ iounmap(upmx->virtbase);
+out_no_remap:
+ platform_set_drvdata(pdev, NULL);
+out_no_memregion:
+ release_mem_region(upmx->phybase, SZ_4K);
+out_no_resource:
+ kfree(upmx);
+ return ret;
+}
+
+static int __exit u300_pmx_remove(struct platform_device *pdev)
+{
+ struct u300_pmx *upmx = platform_get_drvdata(pdev);
+
+ if (upmx) {
+ pinmux_unregister(upmx->pmx);
+ iounmap(upmx->virtbase);
+ release_mem_region(upmx->phybase, upmx->physize);
+ platform_set_drvdata(pdev, NULL);
+ kfree(upmx);
+ }
+
+ return 0;
+}
+
+static struct platform_driver u300_pmx_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(u300_pmx_remove),
+};
+
+static int __init u300_pmx_init(void)
+{
+ return platform_driver_probe(&u300_pmx_driver, u300_pmx_probe);
+}
+arch_initcall(u300_pmx_init);
+
+static void __exit u300_pmx_exit(void)
+{
+ platform_driver_unregister(&u300_pmx_driver);
+}
+module_exit(u300_pmx_exit);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("U300 Padmux driver");
+MODULE_LICENSE("GPL v2");
new file mode 100644
@@ -0,0 +1,141 @@
+/*
+ * Register definitions for the U300 Padmux control registers in the
+ * system controller
+ */
+
+/* PAD MUX Control register 1 (LOW) 16bit (R/W) */
+#define U300_SYSCON_PMC1LR (0x007C)
+#define U300_SYSCON_PMC1LR_MASK (0xFFFF)
+#define U300_SYSCON_PMC1LR_CDI_MASK (0xC000)
+#define U300_SYSCON_PMC1LR_CDI_CDI (0x0000)
+#define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000)
+/* For BS335 */
+#define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000)
+#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000)
+/* For BS365 */
+#define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000)
+#define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000)
+/* Common defs */
+#define U300_SYSCON_PMC1LR_PDI_MASK (0x3000)
+#define U300_SYSCON_PMC1LR_PDI_PDI (0x0000)
+#define U300_SYSCON_PMC1LR_PDI_EGG (0x1000)
+#define U300_SYSCON_PMC1LR_PDI_WCDMA (0x3000)
+#define U300_SYSCON_PMC1LR_MMCSD_MASK (0x0C00)
+#define U300_SYSCON_PMC1LR_MMCSD_MMCSD (0x0000)
+#define U300_SYSCON_PMC1LR_MMCSD_MSPRO (0x0400)
+#define U300_SYSCON_PMC1LR_MMCSD_DSP (0x0800)
+#define U300_SYSCON_PMC1LR_MMCSD_WCDMA (0x0C00)
+#define U300_SYSCON_PMC1LR_ETM_MASK (0x0300)
+#define U300_SYSCON_PMC1LR_ETM_ACC (0x0000)
+#define U300_SYSCON_PMC1LR_ETM_APP (0x0100)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK (0x00C0)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC (0x0000)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF (0x0040)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM (0x0080)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB (0x00C0)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK (0x0030)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC (0x0000)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF (0x0010)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM (0x0020)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI (0x0030)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK (0x000C)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC (0x0000)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF (0x0004)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM (0x0008)
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI (0x000C)
+#define U300_SYSCON_PMC1LR_EMIF_1_MASK (0x0003)
+#define U300_SYSCON_PMC1LR_EMIF_1_STATIC (0x0000)
+#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 (0x0001)
+#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 (0x0002)
+#define U300_SYSCON_PMC1LR_EMIF_1 (0x0003)
+/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */
+#define U300_SYSCON_PMC1HR (0x007E)
+#define U300_SYSCON_PMC1HR_MASK (0xFFFF)
+#define U300_SYSCON_PMC1HR_MISC_2_MASK (0xC000)
+#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_MISC_2_MSPRO (0x4000)
+#define U300_SYSCON_PMC1HR_MISC_2_DSP (0x8000)
+#define U300_SYSCON_PMC1HR_MISC_2_AAIF (0xC000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK (0x3000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF (0x1000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP (0x2000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF (0x3000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK (0x0C00)
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC (0x0400)
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP (0x0800)
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF (0x0C00)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK (0x0300)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI (0x0100)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF (0x0300)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK (0x00C0)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI (0x0040)
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF (0x00C0)
+#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK (0x0030)
+#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI (0x0010)
+#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP (0x0020)
+#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF (0x0030)
+#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK (0x000C)
+#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 (0x0004)
+#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS (0x0008)
+#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF (0x000C)
+#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK (0x0003)
+#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 (0x0001)
+#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF (0x0003)
+/* Padmux 2 control */
+#define U300_SYSCON_PMC2R (0x100)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080)
+#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200)
+#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800)
+#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000)
+/* TODO: More SYSCON registers missing */
+#define U300_SYSCON_PMC3R (0x10c)
+#define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000)
+#define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000)
+#define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000)
+#define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000)
+/* TODO: Missing other configs */
+#define U300_SYSCON_PMC4R (0x168)
+#define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003)
+#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008)
+#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020)
+#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100)
+#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200)