| Message ID | 20180419110056.10342-2-rui.silva@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | media: Introduce Omnivision OV2680 driver | expand |
Hi Rui, On Thu, Apr 19, 2018 at 8:00 AM, Rui Miguel Silva <rui.silva@linaro.org> wrote: > +Optional Properties: > +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, > + if any. This is an active high signal to the OV2680. I looked at the OV2680 datasheet and I see a pin called XSHUTDN, which has the following description: XSHUTDN: reset and power down (active low with internal pull down resistor) So it should be active low, not active high.
Hi Fabio, On Tue 24 Apr 2018 at 15:53, Fabio Estevam wrote: > Hi Rui, > > On Thu, Apr 19, 2018 at 8:00 AM, Rui Miguel Silva > <rui.silva@linaro.org> wrote: >> Add device tree binding documentation for the OV2680 camera >> sensor. >> >> Reviewed-by: Rob Herring <robh@kernel.org> >> CC: devicetree@vger.kernel.org >> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> >> --- >> .../devicetree/bindings/media/i2c/ov2680.txt | 40 >> +++++++++++++++++++ >> 1 file changed, 40 insertions(+) >> create mode 100644 >> Documentation/devicetree/bindings/media/i2c/ov2680.txt >> >> diff --git >> a/Documentation/devicetree/bindings/media/i2c/ov2680.txt >> b/Documentation/devicetree/bindings/media/i2c/ov2680.txt >> new file mode 100644 >> index 000000000000..0e29f1a113c0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt >> @@ -0,0 +1,40 @@ >> +* Omnivision OV2680 MIPI CSI-2 sensor >> + >> +Required Properties: >> +- compatible: should be "ovti,ov2680". >> +- clocks: reference to the xvclk input clock. >> +- clock-names: should be "xvclk". > > You missed to pass the camera power supplies as required > properties: Urgh, yes, you are right, I will add this. --- Cheers, Rui > > DOVDD-supply > AVDD-supply > DVDD-supply
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt new file mode 100644 index 000000000000..0e29f1a113c0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt @@ -0,0 +1,40 @@ +* Omnivision OV2680 MIPI CSI-2 sensor + +Required Properties: +- compatible: should be "ovti,ov2680". +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- powerdown-gpios: reference to the GPIO connected to the powerdown pin, + if any. This is an active high signal to the OV2680. + +The device node must contain one 'port' child node for its digital output +video port, and this port must have a single endpoint in accordance with + the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0). +- data-lanes: should be set to <1> (one CSI-2 lane supported). + +Example: + +&i2c2 { + ov2680: camera-sensor@36 { + compatible = "ovti,ov2680"; + reg = <0x36>; + clocks = <&osc>; + clock-names = "xvclk"; + powerdown-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + + port { + ov2680_mipi_ep: endpoint { + remote-endpoint = <&mipi_sensor_ep>; + clock-lanes = <0>; + data-lanes = <1>; + }; + }; + }; +};