diff mbox

[V8,3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues

Message ID 1364998113-13428-4-git-send-email-amarendra.xt@samsung.com
State New
Headers show

Commit Message

Amar April 3, 2013, 2:08 p.m. UTC
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.

Signed-off-by: Amar <amarendra.xt@samsung.com>
---
Changes since V1:
	1)Created the macros RX_WMARK_SHIFT and RX_WMARK_MASK in header file.

Changes since V2:
	1)Updation of commit message and resubmition of proper patch set.

Changes since V3:
	1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of
	the hard coded value (1 << 10).

Changes since V4:
	1)Updated the function dwmci_send_cmd() to use get_timer() instead
	of using mdelay(1).

Changes since V5:
	1)Updated in response to review comments.

Changes since V6:
	No change.

Changes since V7:
	1)Updated the function dwmci_setup_bus() to return 0 if (freq == 0). 
	This is to avoid the run time exception "raise:Signal # 8 caught".

 drivers/mmc/dw_mmc.c | 28 ++++++++++++++++++----------
 1 file changed, 18 insertions(+), 10 deletions(-)

Comments

Jaehoon Chung April 9, 2013, 10:49 a.m. UTC | #1
Hi Amar,

I'm not sure that need to enable the auto-stop command feature.
why do you enable this feature? Is there any benefit?
Is it related with read/write issue?

Best Regards,
Jaehoon Chung

On 04/03/2013 11:08 PM, Amar wrote:
> This patch enumerates dwmci and set auto stop command during
> dwmci initialisation.
> EMMC read/write is not happening in current implementation
> due to improper fifo size computation. Hence modified the fifo size
> computation to resolve EMMC read write issues.
> 
> Signed-off-by: Amar <amarendra.xt@samsung.com>
> ---
> Changes since V1:
> 	1)Created the macros RX_WMARK_SHIFT and RX_WMARK_MASK in header file.
> 
> Changes since V2:
> 	1)Updation of commit message and resubmition of proper patch set.
> 
> Changes since V3:
> 	1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of
> 	the hard coded value (1 << 10).
> 
> Changes since V4:
> 	1)Updated the function dwmci_send_cmd() to use get_timer() instead
> 	of using mdelay(1).
> 
> Changes since V5:
> 	1)Updated in response to review comments.
> 
> Changes since V6:
> 	No change.
> 
> Changes since V7:
> 	1)Updated the function dwmci_setup_bus() to return 0 if (freq == 0). 
> 	This is to avoid the run time exception "raise:Signal # 8 caught".
> 
>  drivers/mmc/dw_mmc.c | 28 ++++++++++++++++++----------
>  1 file changed, 18 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> index 4070d4e..963a515 100644
> --- a/drivers/mmc/dw_mmc.c
> +++ b/drivers/mmc/dw_mmc.c
> @@ -129,13 +129,13 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
>  	unsigned int timeout = 100000;
>  	u32 retry = 10000;
>  	u32 mask, ctrl;
> +	ulong start = get_timer(0);
>  
>  	while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) {
> -		if (timeout == 0) {
> +		if (get_timer(start) > timeout) {
>  			printf("Timeout on data busy\n");
>  			return TIMEOUT;
>  		}
> -		timeout--;
>  	}
>  
>  	dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_ALL);
> @@ -143,7 +143,6 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
>  	if (data)
>  		dwmci_prepare_data(host, data);
>  
> -
>  	dwmci_writel(host, DWMCI_CMDARG, cmd->cmdarg);
>  
>  	if (data)
> @@ -231,9 +230,8 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
>  	int timeout = 10000;
>  	unsigned long sclk;
>  
> -	if (freq == host->clock)
> +	if ((freq == host->clock) || (freq == 0))
>  		return 0;
> -
>  	/*
>  	 * If host->mmc_clk didn't define,
>  	 * then assume that host->bus_hz is source clock value.
> @@ -314,7 +312,7 @@ static void dwmci_set_ios(struct mmc *mmc)
>  static int dwmci_init(struct mmc *mmc)
>  {
>  	struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
> -	u32 fifo_size, fifoth_val;
> +	u32 fifo_size, fifoth_val, ier;
>  
>  	dwmci_writel(host, DWMCI_PWREN, 1);
>  
> @@ -323,6 +321,14 @@ static int dwmci_init(struct mmc *mmc)
>  		return -1;
>  	}
>  
> +	/* Enumerate at 400KHz */
> +	dwmci_setup_bus(host, mmc->f_min);
> +
> +	/* Set auto stop command */
> +	ier = dwmci_readl(host, DWMCI_CTRL);
> +	ier |= DWMCI_CTRL_SEND_AS_CCSD;
> +	dwmci_writel(host, DWMCI_CTRL, ier);
> +
>  	dwmci_writel(host, DWMCI_RINTSTS, 0xFFFFFFFF);
>  	dwmci_writel(host, DWMCI_INTMASK, 0);
>  
> @@ -332,11 +338,13 @@ static int dwmci_init(struct mmc *mmc)
>  	dwmci_writel(host, DWMCI_BMOD, 1);
>  
>  	fifo_size = dwmci_readl(host, DWMCI_FIFOTH);
> -	if (host->fifoth_val)
> +	fifo_size = ((fifo_size & RX_WMARK_MASK) >> RX_WMARK_SHIFT) + 1;
> +	if (host->fifoth_val) {
>  		fifoth_val = host->fifoth_val;
> -	else
> -		fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size/2 -1) |
> -			TX_WMARK(fifo_size/2);
> +	} else {
> +		fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size / 2 - 1) |
> +			TX_WMARK(fifo_size / 2);
> +	}
>  	dwmci_writel(host, DWMCI_FIFOTH, fifoth_val);
>  
>  	dwmci_writel(host, DWMCI_CLKENA, 0);
>
Amarendra Reddy April 9, 2013, 12:40 p.m. UTC | #2
Hi Jaehoon,

Auto-stop command is not related to read/write issue.
Today, I commented the 'auto-stop command' enable code and tested, SD/EMMC
read write and EMMC boot work fine.
Hence enabling Auto-stop command is not required.
I shall update the same in next patchset.

Thanks & Regards
Amarendra Reddy

On 9 April 2013 16:19, Jaehoon Chung <jh80.chung@samsung.com> wrote:

> Hi Amar,
>
> I'm not sure that need to enable the auto-stop command feature.
> why do you enable this feature? Is there any benefit?
> Is it related with read/write issue?
>
> Best Regards,
> Jaehoon Chung
>
> On 04/03/2013 11:08 PM, Amar wrote:
> > This patch enumerates dwmci and set auto stop command during
> > dwmci initialisation.
> > EMMC read/write is not happening in current implementation
> > due to improper fifo size computation. Hence modified the fifo size
> > computation to resolve EMMC read write issues.
> >
> > Signed-off-by: Amar <amarendra.xt@samsung.com>
> > ---
> > Changes since V1:
> >       1)Created the macros RX_WMARK_SHIFT and RX_WMARK_MASK in header
> file.
> >
> > Changes since V2:
> >       1)Updation of commit message and resubmition of proper patch set.
> >
> > Changes since V3:
> >       1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of
> >       the hard coded value (1 << 10).
> >
> > Changes since V4:
> >       1)Updated the function dwmci_send_cmd() to use get_timer() instead
> >       of using mdelay(1).
> >
> > Changes since V5:
> >       1)Updated in response to review comments.
> >
> > Changes since V6:
> >       No change.
> >
> > Changes since V7:
> >       1)Updated the function dwmci_setup_bus() to return 0 if (freq ==
> 0).
> >       This is to avoid the run time exception "raise:Signal # 8 caught".
> >
> >  drivers/mmc/dw_mmc.c | 28 ++++++++++++++++++----------
> >  1 file changed, 18 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> > index 4070d4e..963a515 100644
> > --- a/drivers/mmc/dw_mmc.c
> > +++ b/drivers/mmc/dw_mmc.c
> > @@ -129,13 +129,13 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> mmc_cmd *cmd,
> >       unsigned int timeout = 100000;
> >       u32 retry = 10000;
> >       u32 mask, ctrl;
> > +     ulong start = get_timer(0);
> >
> >       while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) {
> > -             if (timeout == 0) {
> > +             if (get_timer(start) > timeout) {
> >                       printf("Timeout on data busy\n");
> >                       return TIMEOUT;
> >               }
> > -             timeout--;
> >       }
> >
> >       dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_ALL);
> > @@ -143,7 +143,6 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> mmc_cmd *cmd,
> >       if (data)
> >               dwmci_prepare_data(host, data);
> >
> > -
> >       dwmci_writel(host, DWMCI_CMDARG, cmd->cmdarg);
> >
> >       if (data)
> > @@ -231,9 +230,8 @@ static int dwmci_setup_bus(struct dwmci_host *host,
> u32 freq)
> >       int timeout = 10000;
> >       unsigned long sclk;
> >
> > -     if (freq == host->clock)
> > +     if ((freq == host->clock) || (freq == 0))
> >               return 0;
> > -
> >       /*
> >        * If host->mmc_clk didn't define,
> >        * then assume that host->bus_hz is source clock value.
> > @@ -314,7 +312,7 @@ static void dwmci_set_ios(struct mmc *mmc)
> >  static int dwmci_init(struct mmc *mmc)
> >  {
> >       struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
> > -     u32 fifo_size, fifoth_val;
> > +     u32 fifo_size, fifoth_val, ier;
> >
> >       dwmci_writel(host, DWMCI_PWREN, 1);
> >
> > @@ -323,6 +321,14 @@ static int dwmci_init(struct mmc *mmc)
> >               return -1;
> >       }
> >
> > +     /* Enumerate at 400KHz */
> > +     dwmci_setup_bus(host, mmc->f_min);
> > +
> > +     /* Set auto stop command */
> > +     ier = dwmci_readl(host, DWMCI_CTRL);
> > +     ier |= DWMCI_CTRL_SEND_AS_CCSD;
> > +     dwmci_writel(host, DWMCI_CTRL, ier);
> > +
> >       dwmci_writel(host, DWMCI_RINTSTS, 0xFFFFFFFF);
> >       dwmci_writel(host, DWMCI_INTMASK, 0);
> >
> > @@ -332,11 +338,13 @@ static int dwmci_init(struct mmc *mmc)
> >       dwmci_writel(host, DWMCI_BMOD, 1);
> >
> >       fifo_size = dwmci_readl(host, DWMCI_FIFOTH);
> > -     if (host->fifoth_val)
> > +     fifo_size = ((fifo_size & RX_WMARK_MASK) >> RX_WMARK_SHIFT) + 1;
> > +     if (host->fifoth_val) {
> >               fifoth_val = host->fifoth_val;
> > -     else
> > -             fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size/2 -1) |
> > -                     TX_WMARK(fifo_size/2);
> > +     } else {
> > +             fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size / 2 - 1) |
> > +                     TX_WMARK(fifo_size / 2);
> > +     }
> >       dwmci_writel(host, DWMCI_FIFOTH, fifoth_val);
> >
> >       dwmci_writel(host, DWMCI_CLKENA, 0);
> >
>
> _______________________________________________
> U-Boot mailing list
> U-Boot@lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
diff mbox

Patch

diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
index 4070d4e..963a515 100644
--- a/drivers/mmc/dw_mmc.c
+++ b/drivers/mmc/dw_mmc.c
@@ -129,13 +129,13 @@  static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 	unsigned int timeout = 100000;
 	u32 retry = 10000;
 	u32 mask, ctrl;
+	ulong start = get_timer(0);
 
 	while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) {
-		if (timeout == 0) {
+		if (get_timer(start) > timeout) {
 			printf("Timeout on data busy\n");
 			return TIMEOUT;
 		}
-		timeout--;
 	}
 
 	dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_ALL);
@@ -143,7 +143,6 @@  static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 	if (data)
 		dwmci_prepare_data(host, data);
 
-
 	dwmci_writel(host, DWMCI_CMDARG, cmd->cmdarg);
 
 	if (data)
@@ -231,9 +230,8 @@  static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
 	int timeout = 10000;
 	unsigned long sclk;
 
-	if (freq == host->clock)
+	if ((freq == host->clock) || (freq == 0))
 		return 0;
-
 	/*
 	 * If host->mmc_clk didn't define,
 	 * then assume that host->bus_hz is source clock value.
@@ -314,7 +312,7 @@  static void dwmci_set_ios(struct mmc *mmc)
 static int dwmci_init(struct mmc *mmc)
 {
 	struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
-	u32 fifo_size, fifoth_val;
+	u32 fifo_size, fifoth_val, ier;
 
 	dwmci_writel(host, DWMCI_PWREN, 1);
 
@@ -323,6 +321,14 @@  static int dwmci_init(struct mmc *mmc)
 		return -1;
 	}
 
+	/* Enumerate at 400KHz */
+	dwmci_setup_bus(host, mmc->f_min);
+
+	/* Set auto stop command */
+	ier = dwmci_readl(host, DWMCI_CTRL);
+	ier |= DWMCI_CTRL_SEND_AS_CCSD;
+	dwmci_writel(host, DWMCI_CTRL, ier);
+
 	dwmci_writel(host, DWMCI_RINTSTS, 0xFFFFFFFF);
 	dwmci_writel(host, DWMCI_INTMASK, 0);
 
@@ -332,11 +338,13 @@  static int dwmci_init(struct mmc *mmc)
 	dwmci_writel(host, DWMCI_BMOD, 1);
 
 	fifo_size = dwmci_readl(host, DWMCI_FIFOTH);
-	if (host->fifoth_val)
+	fifo_size = ((fifo_size & RX_WMARK_MASK) >> RX_WMARK_SHIFT) + 1;
+	if (host->fifoth_val) {
 		fifoth_val = host->fifoth_val;
-	else
-		fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size/2 -1) |
-			TX_WMARK(fifo_size/2);
+	} else {
+		fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size / 2 - 1) |
+			TX_WMARK(fifo_size / 2);
+	}
 	dwmci_writel(host, DWMCI_FIFOTH, fifoth_val);
 
 	dwmci_writel(host, DWMCI_CLKENA, 0);