diff mbox series

[v2,3/8] arm64: dts: qcom: pm8150b: Add Base DTS file

Message ID 20190820064216.8629-4-vkoul@kernel.org
State Superseded
Headers show
Series None | expand

Commit Message

Vinod Koul Aug. 20, 2019, 6:42 a.m. UTC
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with pon, adc, and gpio nodes

Signed-off-by: Vinod Koul <vkoul@kernel.org>

---
 arch/arm64/boot/dts/qcom/pm8150b.dtsi | 84 +++++++++++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm8150b.dtsi

-- 
2.20.1
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
new file mode 100644
index 000000000000..dfb71fb8c90a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -0,0 +1,84 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+// Copyright (c) 2019, Linaro Limited
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@2 {
+		compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			status = "disabled";
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+
+			chg-temp@9 {
+				reg = <ADC5_CHG_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "chg_temp";
+			};
+		};
+
+		pm8150b_gpios: gpio@c000 {
+			compatible = "qcom,pm8150b-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc1 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc2 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc3 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc4 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc5 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc6 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc7 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc8 0 IRQ_TYPE_NONE>,
+				     <0x2 0xc9 0 IRQ_TYPE_NONE>,
+				     <0x2 0xca 0 IRQ_TYPE_NONE>,
+				     <0x2 0xcb 0 IRQ_TYPE_NONE>;
+		};
+	};
+
+	pmic@3 {
+		compatible = "qcom,pm8150b", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};