diff mbox

[08/10] Exynos5420: Add base patch for SMDK5420

Message ID 1378124111-26145-9-git-send-email-rajeshwari.s@samsung.com
State New
Headers show

Commit Message

Rajeshwari Shinde Sept. 2, 2013, 12:15 p.m. UTC
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
---
 MAINTAINERS                           |   1 +
 Makefile                              |   2 +-
 board/samsung/common/board.c          |   2 +
 board/samsung/smdk5420/Makefile       |  50 ++++++
 board/samsung/smdk5420/smdk5420.c     | 281 ++++++++++++++++++++++++++++++++++
 board/samsung/smdk5420/smdk5420_spl.c |  68 ++++++++
 boards.cfg                            |   1 +
 tools/Makefile                        |   2 +
 8 files changed, 406 insertions(+), 1 deletion(-)
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
diff mbox

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 9700ec9..97990fb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -939,6 +939,7 @@  Bo Shen <voice.shen@atmel.com>
 Rajeshwari Shinde <rajeshwari.s@samsung.com>
 
 	snow			ARM ARMV7 (EXYNOS5250 SoC)
+	smdk5420		ARM ARMV7 (EXYNOS5420 SoC)
 
 Michal Simek <monstr@monstr.eu>
 
diff --git a/Makefile b/Makefile
index 488db8a..cf1bc1c 100644
--- a/Makefile
+++ b/Makefile
@@ -813,7 +813,7 @@  clean:
 	       $(obj)tools/gdb/{astest,gdbcont,gdbsend}			  \
 	       $(obj)tools/gen_eth_addr    $(obj)tools/img2srec		  \
 	       $(obj)tools/mk{env,}image   $(obj)tools/mpc86x_clk	  \
-	       $(obj)tools/mk{$(BOARD),}spl				  \
+	       $(obj)tools/mk{$(BOARD)}spl				  \
 	       $(obj)tools/mxsboot					  \
 	       $(obj)tools/ncb		   $(obj)tools/ubsha1		  \
 	       $(obj)tools/kernel-doc/docproc				  \
diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c
index bfcfbdf..f255d69 100644
--- a/board/samsung/common/board.c
+++ b/board/samsung/common/board.c
@@ -154,6 +154,7 @@  struct cros_ec_dev *board_get_cros_ec_dev(void)
 	return local.cros_ec_dev;
 }
 
+#ifdef CONFIG_CROS_EC
 static int board_init_cros_ec_devices(const void *blob)
 {
 	local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev);
@@ -162,6 +163,7 @@  static int board_init_cros_ec_devices(const void *blob)
 
 	return 0;
 }
+#endif
 
 #if defined(CONFIG_POWER)
 static int pmic_reg_update(struct pmic *p, int reg, uint regval)
diff --git a/board/samsung/smdk5420/Makefile b/board/samsung/smdk5420/Makefile
new file mode 100644
index 0000000..91dc416
--- /dev/null
+++ b/board/samsung/smdk5420/Makefile
@@ -0,0 +1,50 @@ 
+#
+# Copyright (C) 2012 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	+= smdk5420_spl.o
+
+ifndef CONFIG_SPL_BUILD
+COBJS	+= smdk5420.o
+endif
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL	:=	 $(obj).depend $(LIB)
+
+all:	$(ALL)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c
new file mode 100644
index 0000000..554d0ed
--- /dev/null
+++ b/board/samsung/smdk5420/smdk5420.c
@@ -0,0 +1,281 @@ 
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include <lcd.h>
+#include <netdev.h>
+#include <spi.h>
+#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/sromc.h>
+#include <asm/arch/dp_info.h>
+#include <power/pmic.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_USB_EHCI_EXYNOS
+int board_usb_vbus_init(void)
+{
+	struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+						samsung_get_base_gpio_part1();
+
+	/* Enable VBUS power switch */
+	s5p_gpio_direction_output(&gpio1->x2, 6, 1);
+
+	/* VBUS turn ON time */
+	mdelay(3);
+
+	return 0;
+}
+#endif
+
+int exynos_init(void)
+{
+#ifdef CONFIG_USB_EHCI_EXYNOS
+	board_usb_vbus_init();
+#endif
+	return 0;
+}
+
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+	int err;
+	int node;
+
+	node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+	if (node < 0) {
+		debug("Could not find SROMC node\n");
+		return node;
+	}
+
+	config->bank = fdtdec_get_int(blob, node, "bank", 0);
+	config->width = fdtdec_get_int(blob, node, "width", 2);
+
+	err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+			FDT_SROM_TIMING_COUNT);
+	if (err < 0) {
+		debug("Could not decode SROMC configuration Error: %s\n",
+		      fdt_strerror(err));
+		return -FDT_ERR_NOTFOUND;
+	}
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_SMC911X
+	u32 smc_bw_conf, smc_bc_conf;
+	struct fdt_sromc config;
+	fdt_addr_t base_addr;
+	int node;
+
+	node = decode_sromc(gd->fdt_blob, &config);
+	if (node < 0) {
+		debug("%s: Could not find sromc configuration\n", __func__);
+		return 0;
+	}
+	node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+	if (node < 0) {
+		debug("%s: Could not find lan9215 configuration\n", __func__);
+		return 0;
+	}
+
+	/* We now have a node, so any problems from now on are errors */
+	base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+	if (base_addr == FDT_ADDR_T_NONE) {
+		debug("%s: Could not find lan9215 address\n", __func__);
+		return -1;
+	}
+
+	/* Ethernet needs data bus width of 16 bits */
+	if (config.width != 2) {
+		debug("%s: Unsupported bus width %d\n", __func__,
+		      config.width);
+		return -1;
+	}
+	smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+			| SROMC_BYTE_ENABLE(config.bank);
+
+	smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS])   |
+			SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |
+			SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |
+			SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |
+			SROMC_BC_TAH(config.timing[FDT_SROM_TAH])   |
+			SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |
+			SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+	/* Select and configure the SROMC bank */
+	exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+	s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+	return smc911x_initialize(0, base_addr);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+
+	/* dwmmc initializattion for available channels */
+	ret = exynos_dwmmc_init(gd->fdt_blob);
+	if (ret)
+		debug("dwmmc init failed\n");
+
+	return ret;
+}
+#endif
+
+#if defined(CONFIG_POWER)
+int power_init_board(void)
+{
+	if (pmic_init(I2C_PMIC)) {
+		debug("Could not initialise PMIC\n");
+		return -1;
+	} else {
+		return 0;
+	}
+}
+#endif
+
+#ifdef CONFIG_LCD
+void cfg_lcd_gpio(void)
+{
+	struct exynos5_gpio_part1 *gpio1 =
+		(struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
+
+	/* For Backlight */
+	s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->b2, 0, 1);
+
+	/* LCD power on */
+	s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->x1, 5, 1);
+
+	/* Set Hotplug detect for DP */
+	s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
+}
+
+vidinfo_t panel_info = {
+	.vl_freq	= 60,
+	.vl_col		= 2560,
+	.vl_row		= 1600,
+	.vl_width	= 2560,
+	.vl_height	= 1600,
+	.vl_clkp	= CONFIG_SYS_LOW,
+	.vl_hsp		= CONFIG_SYS_LOW,
+	.vl_vsp		= CONFIG_SYS_LOW,
+	.vl_dp		= CONFIG_SYS_LOW,
+	.vl_bpix	= 4,	/* LCD_BPP = 2^4, for output conosle on LCD */
+
+	/* wDP panel timing infomation */
+	.vl_hspw	= 32,
+	.vl_hbpd	= 80,
+	.vl_hfpd	= 48,
+
+	.vl_vspw	= 6,
+	.vl_vbpd	= 37,
+	.vl_vfpd	= 3,
+	.vl_cmd_allow_len = 0xf,
+
+	.win_id		= 3,
+	.cfg_gpio	= cfg_lcd_gpio,
+	.backlight_on	= NULL,
+	.lcd_power_on	= NULL,
+	.reset_lcd	= NULL,
+	.dual_lcd_enabled = 0,
+
+	.init_delay	= 0,
+	.power_on_delay = 0,
+	.reset_delay	= 0,
+	.interface_mode = FIMD_RGB_INTERFACE,
+	.dp_enabled	= 1,
+};
+
+static struct edp_device_info edp_info = {
+	.disp_info = {
+		.h_res = 2560,
+		.h_sync_width = 32,
+		.h_back_porch = 80,
+		.h_front_porch = 48,
+		.v_res = 1600,
+		.v_sync_width  = 6,
+		.v_back_porch = 37,
+		.v_front_porch = 3,
+		.v_sync_rate = 60,
+	},
+	.lt_info = {
+		.lt_status = DP_LT_NONE,
+	},
+	.video_info = {
+		.master_mode = 0,
+		.bist_mode = DP_DISABLE,
+		.bist_pattern = NO_PATTERN,
+		.h_sync_polarity = 0,
+		.v_sync_polarity = 0,
+		.interlaced = 0,
+		.color_space = COLOR_RGB,
+		.dynamic_range = VESA,
+		.ycbcr_coeff = COLOR_YCBCR601,
+		.color_depth = COLOR_8,
+	},
+};
+
+static struct exynos_dp_platform_data dp_platform_data = {
+	.phy_enable	= set_dp_phy_ctrl,
+	.edp_dev_info	= &edp_info,
+};
+
+void init_panel_info(vidinfo_t *vid)
+{
+	vid->rgb_mode   = MODE_RGB_P,
+
+	exynos_set_dp_platform_data(&dp_platform_data);
+}
+#endif
+
+int board_get_revision(void)
+{
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	const char *board_name;
+
+	board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+	if (board_name == NULL)
+		printf("\nUnknown Board\n");
+	else
+		printf("\nBoard: %s\n", board_name);
+
+	return 0;
+}
+#endif
diff --git a/board/samsung/smdk5420/smdk5420_spl.c b/board/samsung/smdk5420/smdk5420_spl.c
new file mode 100644
index 0000000..7e8911e
--- /dev/null
+++ b/board/samsung/smdk5420/smdk5420_spl.c
@@ -0,0 +1,68 @@ 
+/*
+ * Copyright (c) 2012 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/spl.h>
+#include <asm/arch/clk.h>
+
+#define SIGNATURE	0xdeadbeef
+
+/* Parameters of early board initialization in SPL */
+static struct spl_machine_param machine_param
+		__attribute__((section(".machine_param"))) = {
+	.signature	= SIGNATURE,
+	.version	= 1,
+	.params		= "vmubfasirM",
+	.size		= sizeof(machine_param),
+
+	.mem_iv_size	= 0x1f,
+	.mem_type	= DDR_MODE_DDR3,
+
+	/*
+	 * Set uboot_size to 0x100000 bytes.
+	 *
+	 * This is an overly conservative value chosen to accommodate all
+	 * possible U-Boot image.  You are advised to set this value to a
+	 * smaller realistic size via scripts that modifies the .machine_param
+	 * section of output U-Boot image.
+	 */
+	.uboot_size	= 0x100000,
+
+	.boot_source	= BOOT_MODE_OM,
+	.frequency_mhz	= 800,
+	.arm_freq_mhz	= 900,
+	.serial_base	= 0x12c30000,
+	.i2c_base	= 0x12c60000,
+	.mem_manuf	= MEM_MANUF_SAMSUNG,
+};
+
+struct spl_machine_param *spl_get_machine_params(void)
+{
+	if (machine_param.signature != SIGNATURE) {
+		/* Will hang if SIGNATURE dont match */
+		while (1)
+			;
+	}
+
+	return &machine_param;
+}
diff --git a/boards.cfg b/boards.cfg
index 598561b..c514bf7 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -329,6 +329,7 @@  s5pc210_universal            arm         armv7       universal_c210      samsung
 snow			     arm	 armv7	     smdk5250		 samsung	exynos
 smdk5250		     arm	 armv7	     smdk5250		 samsung	exynos
 smdkv310		     arm	 armv7	     smdkv310		 samsung	exynos
+smdk5420		     arm	 armv7	     smdk5420		 samsung	exynos
 trats                        arm         armv7       trats               samsung        exynos
 harmony                      arm         armv7:arm720t harmony           nvidia         tegra20
 seaboard                     arm         armv7:arm720t seaboard          nvidia         tegra20
diff --git a/tools/Makefile b/tools/Makefile
index b941192..5ddfa80 100644
--- a/tools/Makefile
+++ b/tools/Makefile
@@ -53,6 +53,7 @@  BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
 BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX)
+BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX)
 BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -88,6 +89,7 @@  NOPED_OBJ_FILES-y += omapimage.o
 NOPED_OBJ_FILES-y += mkenvimage.o
 NOPED_OBJ_FILES-y += mkimage.o
 OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o
+OBJ_FILES-$(CONFIG_EXYNOS5420) += mkexynosspl.o
 OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
 OBJ_FILES-$(CONFIG_MX28) += mxsboot.o
 OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o