pinctrl: samsung: Save/restore eint_mask over suspend for EINT_TYPE GPIOs

Message ID BN6PR04MB06600C848C2C1531F73DAD7BA3D10@BN6PR04MB0660.namprd04.prod.outlook.com
State New
Headers show
Series
  • pinctrl: samsung: Save/restore eint_mask over suspend for EINT_TYPE GPIOs
Related show

Commit Message

Jonathan Bakker April 25, 2020, 11:10 p.m.
Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers
are saved and restored over a suspend/resume cycle.  However, the
EINT_MASK registers are not.

On S5PV210 at the very least, these registers are not retained over
suspend, leading to the interrupts remaining masked upon resume and
therefore no interrupts being triggered for the device.  There should
be no effect on any SoCs that do retain these registers as theoretically
we would just be re-writing what was already there.

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 9 +++++++++
 1 file changed, 9 insertions(+)

Patch

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 0599f5127b01..e6ddb54afaf2 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -265,6 +265,7 @@  struct exynos_eint_gpio_save {
 	u32 eint_con;
 	u32 eint_fltcon0;
 	u32 eint_fltcon1;
+	u32 eint_mask;
 };
 
 /*
@@ -608,10 +609,13 @@  static void exynos_pinctrl_suspend_bank(
 						+ 2 * bank->eint_offset);
 	save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
 						+ 2 * bank->eint_offset + 4);
+	save->eint_mask = readl(regs + bank->irq_chip->eint_mask
+						+ bank->eint_offset);
 
 	pr_debug("%s: save     con %#010x\n", bank->name, save->eint_con);
 	pr_debug("%s: save fltcon0 %#010x\n", bank->name, save->eint_fltcon0);
 	pr_debug("%s: save fltcon1 %#010x\n", bank->name, save->eint_fltcon1);
+	pr_debug("%s: save    mask %#010x\n", bank->name, save->eint_mask);
 }
 
 void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
@@ -653,6 +657,9 @@  static void exynos_pinctrl_resume_bank(
 	pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
 			readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
 			+ 2 * bank->eint_offset + 4), save->eint_fltcon1);
+	pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
+			readl(regs + bank->irq_chip->eint_mask
+			+ bank->eint_offset), save->eint_mask);
 
 	writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
 						+ bank->eint_offset);
@@ -660,6 +667,8 @@  static void exynos_pinctrl_resume_bank(
 						+ 2 * bank->eint_offset);
 	writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
 						+ 2 * bank->eint_offset + 4);
+	writel(save->eint_mask, regs + bank->irq_chip->eint_mask
+						+ bank->eint_offset);
 }
 
 void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)