@@ -604,6 +604,33 @@
};
};
};
+
+ mcde {
+ lcd_default_mode: lcd_default {
+ default_mux {
+ /* Mux in VSI0 and all the data lines */
+ ste,function = "lcd";
+ ste,pins =
+ "lcdvsi0_a_1", /* VSI0 for LCD */
+ "lcd_d0_d7_a_1", /* Data lines */
+ "lcd_d8_d11_a_1", /* TV-out */
+ "lcdaclk_b_1", /* Clock line for TV-out */
+ "lcdvsi1_a_1"; /* VSI1 for HDMI */
+ };
+ default_cfg1 {
+ ste,pins =
+ "GPIO68_E1", /* VSI0 */
+ "GPIO69_E2"; /* VSI1 */
+ ste,config = <&in_pu>;
+ };
+ };
+ lcd_sleep_mode: lcd_sleep {
+ sleep_cfg1 {
+ ste,pins = "GPIO69_E2"; /* VSI1 */
+ ste,config = <&slpm_in_wkup_pdis>;
+ };
+ };
+ };
};
};
};
@@ -261,5 +261,11 @@
};
};
};
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
@@ -362,5 +362,11 @@
};
};
};
+
+ mcde@a0350000 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&lcd_default_mode>;
+ pinctrl-1 = <&lcd_sleep_mode>;
+ };
};
};
@@ -46,8 +46,6 @@ BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(slpm_in_wkup_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
-BIAS(slpm_wkup_pdis, PIN_SLEEPMODE_ENABLED|
- PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_pdis, PIN_SLEEPMODE_ENABLED|
PIN_SLPM_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE|PIN_SLPM_PDIS_DISABLED);
BIAS(slpm_out_lo_wkup_pdis, PIN_SLEEPMODE_ENABLED|
@@ -325,23 +323,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
/* Pin control settings */
static struct pinctrl_map __initdata mop500_family_pinmap[] = {
- /*
- * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
- * pull-up
- * TODO: is this really correct? Snowball doesn't have a LCD.
- */
- DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
- DB8500_PIN_HOG("GPIO68_E1", in_pu),
- DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
- /* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
- DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
- DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
- /* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
- DB8500_MUX("lcdvsi1_a_1", "lcd", "0-0070"),
- DB8500_PIN("GPIO69_E2", in_pu, "0-0070"),
- /* LCD VSI1 sleep state */
- DB8500_PIN_SLEEP("GPIO69_E2", slpm_in_wkup_pdis, "0-0070"),
-
/* ske default state */
DB8500_MUX("kp_a_2", "kp", "nmk-ske-keypad"),
DB8500_PIN("GPIO153_B17", in_pd, "nmk-ske-keypad"), /* I7 */
This moves the MCDE pin control table out of the board file and into the device tree. Some pins and configs have been marked as used by sub-devices or slaves to the MCDE, such as I2C device 0-070 which is the HDMI interface circuit AV8100, but the pins rather belong to the MCDE SOC block as they come out of the main ASIC. The touch screen GPIO is not related to MCDE so this gets deleted and need to be tied to the respective touch screen (I2C) device once that device is added instead. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/boot/dts/ste-href-family-pinctrl.dtsi | 27 ++++++++++++++++++++++++++ arch/arm/boot/dts/ste-href.dtsi | 6 ++++++ arch/arm/boot/dts/ste-snowball.dts | 6 ++++++ arch/arm/mach-ux500/board-mop500-pins.c | 19 ------------------ 4 files changed, 39 insertions(+), 19 deletions(-)