diff mbox series

[v2,net-next,02/13] net: dsa: felix: set proper link speed in felix_phylink_mac_config

Message ID 20200530115142.707415-3-olteanv@gmail.com
State New
Headers show
Series New DSA driver for VSC9953 Seville switch | expand

Commit Message

Vladimir Oltean May 30, 2020, 11:51 a.m. UTC
From: Vladimir Oltean <vladimir.oltean@nxp.com>

state->speed holds a value of 10, 100, 1000 or 2500, but
SYS_MAC_FC_CFG_FC_LINK_SPEE and DEV_CLOCK_CFG_LINK_SPEED expect a value
in the range 0, 1, 2 or 3.

Even truncated to 2 bits, we are still writing incorrect values to the
registers, but for some reason Felix still works.

On Seville (which we're introducing now), however, we need to set
correct values for the link speed into the MAC registers. Do that now.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
Changes in v2:
Patch is new.

 drivers/net/dsa/ocelot/felix.c | 40 +++++++++++++++++++++++++++-------
 1 file changed, 32 insertions(+), 8 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index a6e272d2110d..6ba0d2c3c2fa 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -208,18 +208,39 @@  static void felix_phylink_mac_config(struct dsa_switch *ds, int port,
 	struct ocelot *ocelot = ds->priv;
 	struct ocelot_port *ocelot_port = ocelot->ports[port];
 	struct felix *felix = ocelot_to_felix(ocelot);
-	u32 mac_fc_cfg;
+	u32 clock_cfg, mac_fc_cfg;
+
+	switch (state->speed) {
+	case SPEED_10:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(3);
+		clock_cfg = DEV_CLOCK_CFG_LINK_SPEED(3);
+		break;
+	case SPEED_100:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(2);
+		clock_cfg = DEV_CLOCK_CFG_LINK_SPEED(2);
+		break;
+	case SPEED_1000:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(1);
+		clock_cfg = DEV_CLOCK_CFG_LINK_SPEED(1);
+		break;
+	case SPEED_2500:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(1);
+		clock_cfg = DEV_CLOCK_CFG_LINK_SPEED(0);
+		break;
+	case SPEED_UNKNOWN:
+		mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(0);
+		clock_cfg = DEV_CLOCK_CFG_LINK_SPEED(0);
+		break;
+	default:
+		dev_err(ocelot->dev, "Unsupported speed on port %d: %d\n",
+			port, state->speed);
+		return;
+	}
 
 	/* Take port out of reset by clearing the MAC_TX_RST, MAC_RX_RST and
 	 * PORT_RST bits in CLOCK_CFG
 	 */
-	ocelot_port_writel(ocelot_port, DEV_CLOCK_CFG_LINK_SPEED(state->speed),
-			   DEV_CLOCK_CFG);
-
-	/* Flow control. Link speed is only used here to evaluate the time
-	 * specification in incoming pause frames.
-	 */
-	mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(state->speed);
+	ocelot_port_writel(ocelot_port, clock_cfg, DEV_CLOCK_CFG);
 
 	/* handle Rx pause in all cases, with 2500base-X this is used for rate
 	 * adaptation.
@@ -231,6 +252,9 @@  static void felix_phylink_mac_config(struct dsa_switch *ds, int port,
 			      SYS_MAC_FC_CFG_PAUSE_VAL_CFG(0xffff) |
 			      SYS_MAC_FC_CFG_FC_LATENCY_CFG(0x7) |
 			      SYS_MAC_FC_CFG_ZERO_PAUSE_ENA;
+	/* Flow control. Link speed is only used here to evaluate the time
+	 * specification in incoming pause frames.
+	 */
 	ocelot_write_rix(ocelot, mac_fc_cfg, SYS_MAC_FC_CFG, port);
 
 	ocelot_write_rix(ocelot, 0, ANA_POL_FLOWC, port);