diff mbox series

[net-next,v3,08/10] net: phy: marvell: Add cable test support

Message ID 20200509162851.362346-9-andrew@lunn.ch
State Superseded
Headers show
Series Ethernet Cable test support | expand

Commit Message

Andrew Lunn May 9, 2020, 4:28 p.m. UTC
The Marvell PHYs have a couple of different register sets for
performing cable tests. Page 7 provides the simplest to use.

v3:
s/mavell/marvell/g
Remove include of <uapi/linux/ethtool_netlink.h>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
 drivers/net/phy/marvell.c | 201 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 201 insertions(+)
diff mbox series

Patch

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 7fc8e10c5f33..4bc7febf9248 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -27,6 +27,7 @@ 
 #include <linux/module.h>
 #include <linux/mii.h>
 #include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
 #include <linux/phy.h>
 #include <linux/marvell_phy.h>
 #include <linux/bitfield.h>
@@ -42,6 +43,7 @@ 
 #define MII_MARVELL_MSCR_PAGE		0x02
 #define MII_MARVELL_LED_PAGE		0x03
 #define MII_MARVELL_MISC_TEST_PAGE	0x06
+#define MII_MARVELL_VCT7_PAGE		0x07
 #define MII_MARVELL_WOL_PAGE		0x11
 
 #define MII_M1011_IEVENT		0x13
@@ -162,6 +164,36 @@ 
 #define MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII	0x1	/* SGMII to copper */
 #define MII_88E1510_GEN_CTRL_REG_1_RESET	0x8000	/* Soft reset */
 
+#define MII_VCT7_PAIR_0_DISTANCE	0x10
+#define MII_VCT7_PAIR_1_DISTANCE	0x11
+#define MII_VCT7_PAIR_2_DISTANCE	0x12
+#define MII_VCT7_PAIR_3_DISTANCE	0x13
+
+#define MII_VCT7_RESULTS	0x14
+#define MII_VCT7_RESULTS_PAIR3_MASK	0xf000
+#define MII_VCT7_RESULTS_PAIR2_MASK	0x0f00
+#define MII_VCT7_RESULTS_PAIR1_MASK	0x00f0
+#define MII_VCT7_RESULTS_PAIR0_MASK	0x000f
+#define MII_VCT7_RESULTS_PAIR3_SHIFT	12
+#define MII_VCT7_RESULTS_PAIR2_SHIFT	8
+#define MII_VCT7_RESULTS_PAIR1_SHIFT	4
+#define MII_VCT7_RESULTS_PAIR0_SHIFT	0
+#define MII_VCT7_RESULTS_INVALID	0
+#define MII_VCT7_RESULTS_OK		1
+#define MII_VCT7_RESULTS_OPEN		2
+#define MII_VCT7_RESULTS_SAME_SHORT	3
+#define MII_VCT7_RESULTS_CROSS_SHORT	4
+#define MII_VCT7_RESULTS_BUSY		9
+
+#define MII_VCT7_CTRL		0x15
+#define MII_VCT7_CTRL_RUN_NOW			BIT(15)
+#define MII_VCT7_CTRL_RUN_ANEG			BIT(14)
+#define MII_VCT7_CTRL_DISABLE_CROSS		BIT(13)
+#define MII_VCT7_CTRL_RUN_AFTER_BREAK_LINK	BIT(12)
+#define MII_VCT7_CTRL_IN_PROGRESS		BIT(11)
+#define MII_VCT7_CTRL_METERS			BIT(10)
+#define MII_VCT7_CTRL_CENTIMETERS		0
+
 #define LPA_PAUSE_FIBER		0x180
 #define LPA_PAUSE_ASYM_FIBER	0x100
 
@@ -1658,6 +1690,163 @@  static void marvell_get_stats(struct phy_device *phydev,
 		data[i] = marvell_get_stat(phydev, i);
 }
 
+static int marvell_vct7_cable_test_start(struct phy_device *phydev)
+{
+	int bmcr, bmsr, ret;
+
+	/* If auto-negotiation is enabled, but not complete, the cable
+	 * test never completes. So disable auto-neg.
+	 */
+	bmcr = phy_read(phydev, MII_BMCR);
+	if (bmcr < 0)
+		return bmcr;
+
+	bmsr = phy_read(phydev, MII_BMSR);
+
+	if (bmsr < 0)
+		return bmsr;
+
+	if (bmcr & BMCR_ANENABLE) {
+		ret =  phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0);
+		if (ret < 0)
+			return ret;
+		ret = genphy_soft_reset(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* If the link is up, allow it some time to go down */
+	if (bmsr & BMSR_LSTATUS)
+		msleep(1500);
+
+	return phy_write_paged(phydev, MII_MARVELL_VCT7_PAGE,
+			       MII_VCT7_CTRL,
+			       MII_VCT7_CTRL_RUN_NOW |
+			       MII_VCT7_CTRL_CENTIMETERS);
+}
+
+static int marvell_vct7_distance_to_length(int distance, bool meter)
+{
+	if (meter)
+		distance *= 100;
+
+	return distance;
+}
+
+static bool marvell_vct7_distance_valid(int result)
+{
+	switch (result) {
+	case MII_VCT7_RESULTS_OPEN:
+	case MII_VCT7_RESULTS_SAME_SHORT:
+	case MII_VCT7_RESULTS_CROSS_SHORT:
+		return true;
+	}
+	return false;
+}
+
+static int marvell_vct7_report_length(struct phy_device *phydev,
+				      int pair, bool meter)
+{
+	int length;
+	int ret;
+
+	ret = phy_read_paged(phydev, MII_MARVELL_VCT7_PAGE,
+			     MII_VCT7_PAIR_0_DISTANCE + pair);
+	if (ret < 0)
+		return ret;
+
+	length = marvell_vct7_distance_to_length(ret, meter);
+
+	ethnl_cable_test_fault_length(phydev, pair, length);
+
+	return 0;
+}
+
+static int marvell_vct7_cable_test_report_trans(int result)
+{
+	switch (result) {
+	case MII_VCT7_RESULTS_OK:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+	case MII_VCT7_RESULTS_OPEN:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+	case MII_VCT7_RESULTS_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+	case MII_VCT7_RESULTS_CROSS_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+	default:
+		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+}
+
+static int marvell_vct7_cable_test_report(struct phy_device *phydev)
+{
+	int pair0, pair1, pair2, pair3;
+	bool meter;
+	int ret;
+
+	ret = phy_read_paged(phydev, MII_MARVELL_VCT7_PAGE,
+			     MII_VCT7_RESULTS);
+	if (ret < 0)
+		return ret;
+
+	pair3 = (ret & MII_VCT7_RESULTS_PAIR3_MASK) >>
+		MII_VCT7_RESULTS_PAIR3_SHIFT;
+	pair2 = (ret & MII_VCT7_RESULTS_PAIR2_MASK) >>
+		MII_VCT7_RESULTS_PAIR2_SHIFT;
+	pair1 = (ret & MII_VCT7_RESULTS_PAIR1_MASK) >>
+		MII_VCT7_RESULTS_PAIR1_SHIFT;
+	pair0 = (ret & MII_VCT7_RESULTS_PAIR0_MASK) >>
+		MII_VCT7_RESULTS_PAIR0_SHIFT;
+
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+				marvell_vct7_cable_test_report_trans(pair0));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B,
+				marvell_vct7_cable_test_report_trans(pair1));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C,
+				marvell_vct7_cable_test_report_trans(pair2));
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D,
+				marvell_vct7_cable_test_report_trans(pair3));
+
+	ret = phy_read_paged(phydev, MII_MARVELL_VCT7_PAGE, MII_VCT7_CTRL);
+	if (ret < 0)
+		return ret;
+
+	meter = ret & MII_VCT7_CTRL_METERS;
+
+	if (marvell_vct7_distance_valid(pair0))
+		marvell_vct7_report_length(phydev, 0, meter);
+	if (marvell_vct7_distance_valid(pair1))
+		marvell_vct7_report_length(phydev, 1, meter);
+	if (marvell_vct7_distance_valid(pair2))
+		marvell_vct7_report_length(phydev, 2, meter);
+	if (marvell_vct7_distance_valid(pair3))
+		marvell_vct7_report_length(phydev, 3, meter);
+
+	return 0;
+}
+
+static int marvell_vct7_cable_test_get_status(struct phy_device *phydev,
+					      bool *finished)
+{
+	int ret;
+
+	*finished = false;
+
+	ret = phy_read_paged(phydev, MII_MARVELL_VCT7_PAGE,
+			     MII_VCT7_CTRL);
+
+	if (ret < 0)
+		return ret;
+
+	if (!(ret & MII_VCT7_CTRL_IN_PROGRESS)) {
+		*finished = true;
+
+		return marvell_vct7_cable_test_report(phydev);
+	}
+
+	return 0;
+}
+
 #ifdef CONFIG_HWMON
 static int m88e1121_get_temp(struct phy_device *phydev, long *temp)
 {
@@ -2353,6 +2542,7 @@  static struct phy_driver marvell_drivers[] = {
 		.phy_id_mask = MARVELL_PHY_ID_MASK,
 		.name = "Marvell 88E1510",
 		.features = PHY_GBIT_FIBRE_FEATURES,
+		.flags = PHY_POLL_CABLE_TEST,
 		.probe = &m88e1510_probe,
 		.config_init = &m88e1510_config_init,
 		.config_aneg = &m88e1510_config_aneg,
@@ -2372,12 +2562,15 @@  static struct phy_driver marvell_drivers[] = {
 		.set_loopback = genphy_loopback,
 		.get_tunable = m88e1011_get_tunable,
 		.set_tunable = m88e1011_set_tunable,
+		.cable_test_start = marvell_vct7_cable_test_start,
+		.cable_test_get_status = marvell_vct7_cable_test_get_status,
 	},
 	{
 		.phy_id = MARVELL_PHY_ID_88E1540,
 		.phy_id_mask = MARVELL_PHY_ID_MASK,
 		.name = "Marvell 88E1540",
 		/* PHY_GBIT_FEATURES */
+		.flags = PHY_POLL_CABLE_TEST,
 		.probe = m88e1510_probe,
 		.config_init = &marvell_config_init,
 		.config_aneg = &m88e1510_config_aneg,
@@ -2394,6 +2587,8 @@  static struct phy_driver marvell_drivers[] = {
 		.get_stats = marvell_get_stats,
 		.get_tunable = m88e1540_get_tunable,
 		.set_tunable = m88e1540_set_tunable,
+		.cable_test_start = marvell_vct7_cable_test_start,
+		.cable_test_get_status = marvell_vct7_cable_test_get_status,
 	},
 	{
 		.phy_id = MARVELL_PHY_ID_88E1545,
@@ -2401,6 +2596,7 @@  static struct phy_driver marvell_drivers[] = {
 		.name = "Marvell 88E1545",
 		.probe = m88e1510_probe,
 		/* PHY_GBIT_FEATURES */
+		.flags = PHY_POLL_CABLE_TEST,
 		.config_init = &marvell_config_init,
 		.config_aneg = &m88e1510_config_aneg,
 		.read_status = &marvell_read_status,
@@ -2416,6 +2612,8 @@  static struct phy_driver marvell_drivers[] = {
 		.get_stats = marvell_get_stats,
 		.get_tunable = m88e1540_get_tunable,
 		.set_tunable = m88e1540_set_tunable,
+		.cable_test_start = marvell_vct7_cable_test_start,
+		.cable_test_get_status = marvell_vct7_cable_test_get_status,
 	},
 	{
 		.phy_id = MARVELL_PHY_ID_88E3016,
@@ -2442,6 +2640,7 @@  static struct phy_driver marvell_drivers[] = {
 		.phy_id_mask = MARVELL_PHY_ID_MASK,
 		.name = "Marvell 88E6390",
 		/* PHY_GBIT_FEATURES */
+		.flags = PHY_POLL_CABLE_TEST,
 		.probe = m88e6390_probe,
 		.config_init = &marvell_config_init,
 		.config_aneg = &m88e6390_config_aneg,
@@ -2458,6 +2657,8 @@  static struct phy_driver marvell_drivers[] = {
 		.get_stats = marvell_get_stats,
 		.get_tunable = m88e1540_get_tunable,
 		.set_tunable = m88e1540_set_tunable,
+		.cable_test_start = marvell_vct7_cable_test_start,
+		.cable_test_get_status = marvell_vct7_cable_test_get_status,
 	},
 };