| Message ID | 20200618141259.155581-1-jagan@amarulasolutions.com |
|---|---|
| State | Accepted |
| Commit | cd7bf74e0e853bea3618a70e378049ec0ec67b7f |
| Headers | show |
| Series | [v2,1/6] rock-pi-4: Enable USB3 Host | expand |
On 2020/6/18 ??10:12, Jagan Teki wrote: > Enable USB3.0 Host support for RockPI-4 boards. > > Note that the Upper USB3.0 port is marked as otg and > lower USB3.0 port marked as host, so this below log > capture when USB3.0 mass storage plug in at lower > USB 3.0 port. > > Log: > Bus usb at fe380000: USB EHCI 1.00 > Bus usb at fe3c0000: USB EHCI 1.00 > Bus dwc3: usb maximum-speed not found > Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.10 > Bus dwc3: usb maximum-speed not found > Register 2000140 NbrPorts 2 > Starting the controller > USB XHCI 1.10 > scanning bus usb at fe380000 for devices... 1 USB Device(s) found > scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found > scanning bus dwc3 for devices... 1 USB Device(s) found > scanning bus dwc3 for devices... cannot reset port 1!? > 2 USB Device(s) found > scanning usb for storage devices... 1 Storage Device(s) found > => usb tree > USB device tree: > 1 Hub (480 Mb/s, 0mA) > u-boot EHCI Host Controller > > 1 Hub (480 Mb/s, 0mA) > u-boot EHCI Host Controller > > 1 Hub (5 Gb/s, 0mA) > U-Boot XHCI Host Controller > > 1 Hub (5 Gb/s, 0mA) > | U-Boot XHCI Host Controller > | > +-2 Mass Storage (5 Gb/s, 224mA) > SanDisk Dual Drive 040130e3ee554b7078843f4eb331646 > > Cc: Tom Cubie <tom at radxa.com> > Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang at rock-chips.com> Thanks, - Kever > --- > Changes for v2: > - rebase on master > > configs/rock-pi-4-rk3399_defconfig | 6 ++++++ > 1 file changed, 6 insertions(+) > > diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4-rk3399_defconfig > index 0d86fdc895..2487872219 100644 > --- a/configs/rock-pi-4-rk3399_defconfig > +++ b/configs/rock-pi-4-rk3399_defconfig > @@ -28,6 +28,7 @@ CONFIG_ENV_IS_IN_MMC=y > CONFIG_SYS_RELOC_GD_ENV_ADDR=y > CONFIG_ROCKCHIP_GPIO=y > CONFIG_SYS_I2C_ROCKCHIP=y > +CONFIG_MISC=y > CONFIG_MMC_DW=y > CONFIG_MMC_DW_ROCKCHIP=y > CONFIG_MMC_SDHCI=y > @@ -35,11 +36,14 @@ CONFIG_MMC_SDHCI_ROCKCHIP=y > CONFIG_DM_ETH=y > CONFIG_ETH_DESIGNWARE=y > CONFIG_GMAC_ROCKCHIP=y > +CONFIG_PHY_ROCKCHIP_INNO_USB2=y > +CONFIG_PHY_ROCKCHIP_TYPEC=y > CONFIG_PMIC_RK8XX=y > CONFIG_REGULATOR_PWM=y > CONFIG_REGULATOR_RK8XX=y > CONFIG_PWM_ROCKCHIP=y > CONFIG_RAM_RK3399_LPDDR4=y > +CONFIG_DM_RESET=y > CONFIG_BAUDRATE=1500000 > CONFIG_DEBUG_UART_SHIFT=2 > CONFIG_SYSRESET=y > @@ -48,6 +52,8 @@ CONFIG_USB_XHCI_HCD=y > CONFIG_USB_XHCI_DWC3=y > CONFIG_USB_EHCI_HCD=y > CONFIG_USB_EHCI_GENERIC=y > +CONFIG_USB_DWC3=y > +CONFIG_USB_DWC3_GENERIC=y > CONFIG_USB_HOST_ETHER=y > CONFIG_USB_ETHER_ASIX=y > CONFIG_USB_ETHER_ASIX88179=y
diff --git a/configs/rock-pi-4-rk3399_defconfig b/configs/rock-pi-4-rk3399_defconfig index 0d86fdc895..2487872219 100644 --- a/configs/rock-pi-4-rk3399_defconfig +++ b/configs/rock-pi-4-rk3399_defconfig @@ -28,6 +28,7 @@ CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_ROCKCHIP_GPIO=y CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y CONFIG_MMC_DW=y CONFIG_MMC_DW_ROCKCHIP=y CONFIG_MMC_SDHCI=y @@ -35,11 +36,14 @@ CONFIG_MMC_SDHCI_ROCKCHIP=y CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_TYPEC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y CONFIG_REGULATOR_RK8XX=y CONFIG_PWM_ROCKCHIP=y CONFIG_RAM_RK3399_LPDDR4=y +CONFIG_DM_RESET=y CONFIG_BAUDRATE=1500000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_SYSRESET=y @@ -48,6 +52,8 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y CONFIG_USB_HOST_ETHER=y CONFIG_USB_ETHER_ASIX=y CONFIG_USB_ETHER_ASIX88179=y
Enable USB3.0 Host support for RockPI-4 boards. Note that the Upper USB3.0 port is marked as otg and lower USB3.0 port marked as host, so this below log capture when USB3.0 mass storage plug in at lower USB 3.0 port. Log: Bus usb at fe380000: USB EHCI 1.00 Bus usb at fe3c0000: USB EHCI 1.00 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb at fe380000 for devices... 1 USB Device(s) found scanning bus usb at fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... cannot reset port 1!? 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (480 Mb/s, 0mA) u-boot EHCI Host Controller 1 Hub (5 Gb/s, 0mA) U-Boot XHCI Host Controller 1 Hub (5 Gb/s, 0mA) | U-Boot XHCI Host Controller | +-2 Mass Storage (5 Gb/s, 224mA) SanDisk Dual Drive 040130e3ee554b7078843f4eb331646 Cc: Tom Cubie <tom at radxa.com> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- Changes for v2: - rebase on master configs/rock-pi-4-rk3399_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)