[v3,3/5] cmd: mvebu: bubt: verify A38x target device type

Ensure that the device to which an image is being written includes
header information indicating boot support for the destination
device.

This is derived from the support in the SolidRun master-a38x vendor
fork.

Signed-off-by: Joel Johnson <mrjoel at lixil.net>

---

v2 changes:
  - none
v3 changes:
  - use ARRAY_SIZE instead of #define size

---
 cmd/mvebu/bubt.c | 47 +++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 45 insertions(+), 2 deletions(-)

On 23.03.20 18:43, Joel Johnson wrote:
> Ensure that the device to which an image is being written includes
> header information indicating boot support for the destination
> device.
> 
> This is derived from the support in the SolidRun master-a38x vendor
> fork.
> 
> Signed-off-by: Joel Johnson <mrjoel at lixil.net>
> 
> ---
> 
> v2 changes:
>    - none
> v3 changes:
>    - use ARRAY_SIZE instead of #define size
> 
> ---
>   cmd/mvebu/bubt.c | 47 +++++++++++++++++++++++++++++++++++++++++++++--
>   1 file changed, 45 insertions(+), 2 deletions(-)
> 
> diff --git a/cmd/mvebu/bubt.c b/cmd/mvebu/bubt.c
> index b80b81c82a..fbcad37c40 100644
> --- a/cmd/mvebu/bubt.c
> +++ b/cmd/mvebu/bubt.c
> @@ -107,6 +107,24 @@ struct a38x_main_hdr_v1 {
>   	u8  ext;                   /* 0x1E      */
>   	u8  checksum;              /* 0x1F      */
>   };
> +
> +struct a38x_boot_mode {
> +	unsigned int id;
> +	const char *name;
> +};
> +
> +/* The blockid header field values used to indicate boot device of image */
> +struct a38x_boot_mode a38x_boot_modes[] = {
> +	{ 0x4D, "i2c"  },
> +	{ 0x5A, "spi"  },
> +	{ 0x69, "uart" },
> +	{ 0x78, "sata" },
> +	{ 0x8B, "nand" },
> +	{ 0x9C, "pex"  },
> +	{ 0xAE, "mmc"  },
> +	{},
> +};
> +
>   #endif
>   
>   struct bubt_dev {
> @@ -644,6 +662,23 @@ static int check_image_header(void)
>   	return 0;
>   }
>   #elif defined(CONFIG_ARMADA_38X)
> +static int a38x_check_boot_mode(const struct bubt_dev *dst)
> +{
> +	int mode;
> +	const struct a38x_main_hdr_v1 *hdr =
> +		(struct a38x_main_hdr_v1 *)get_load_addr();
> +
> +	for (mode = 0; mode < ARRAY_SIZE(a38x_boot_modes); mode++) {
> +		if (strcmp(a38x_boot_modes[mode].name, dst->name) == 0)
> +			break;
> +	}
> +
> +	if (a38x_boot_modes[mode].id == hdr->blockid)
> +		return 0;
> +
> +	return -ENOEXEC;
> +}
> +
>   static size_t a38x_header_size(const struct a38x_main_hdr_v1 *h)
>   {
>   	if (h->version == 1)
> @@ -697,7 +732,7 @@ static int check_image_header(void)
>   }
>   #endif
>   
> -static int bubt_verify(size_t image_size)
> +static int bubt_verify(const struct bubt_dev *dst)
>   {
>   	int err;
>   
> @@ -708,6 +743,14 @@ static int bubt_verify(size_t image_size)
>   		return err;
>   	}
>   
> +#if defined(CONFIG_ARMADA_38X)
> +	err = a38x_check_boot_mode(dst);
> +	if (err) {
> +		puts("Error: image not built for destination device!\n");
> +		return err;
> +	}
> +#endif

Sorry for spotting this so late, but could you please change this to

	if (IS_ENABLED(CONFIG_ARMADA_38X)) {
		err = a38x_check_boot_mode(dst);
		...

instead (less #ifdef's).

Other than that, please add my:

Reviewed-by: Stefan Roese <sr at denx.de>

Thanks,
Stefan

> +
>   	return 0;
>   }
>   
> @@ -829,7 +872,7 @@ int do_bubt_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
>   	if (!image_size)
>   		return -EIO;
>   
> -	err = bubt_verify(image_size);
> +	err = bubt_verify(dst);
>   	if (err)
>   		return err;
>   
> 


Viele Gr??e,
Stefan