@@ -7,10 +7,17 @@ controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA.
Required properties (controller (parent) node):
- compatible : should be one of
"mediatek,generic-tphy-v1"
- - clocks : (deprecated, use port's clocks instead) a list of phandle +
- clock-specifier pairs, one for each entry in clock-names
- - clock-names : (deprecated, use port's one instead) must contain
- "u3phya_ref": for reference clock of usb3.0 analog phy.
+ "mediatek,generic-tphy-v2"
+
+- #address-cells: the number of cells used to represent physical
+ base addresses.
+- #size-cells: the number of cells used to represent the size of an address.
+- ranges: the address mapping relationship to the parent, defined with
+ - empty value: if optional 'reg' is used.
+ - non-empty value: if optional 'reg' is not used. should set
+ the child's base address to 0, the physical address
+ within parent's address space, and the length of
+ the address map.
Required nodes : a sub-node is required for each port the controller
provides. Address range information including the usual
@@ -27,12 +34,6 @@ Optional properties (controller (parent) node):
Required properties (port (child) node):
- reg : address and length of the register set for the port.
-- clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
-- clock-names : must contain
- "ref": 48M reference clock for HighSpeed analog phy; and 26M
- reference clock for SuperSpeed analog phy, sometimes is
- 24M, 25M or 27M, depended on platform.
- #phy-cells : should be 1 (See second example)
cell after port phandle is phy type from:
- PHY_TYPE_USB2
@@ -40,6 +41,17 @@ Required properties (port (child) node):
- PHY_TYPE_PCIE
- PHY_TYPE_SATA
+Optional properties (port (child) node):
+- clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+- clock-names : may contain
+ "ref": 48M reference clock for HighSpeed (digital) phy; and 26M
+ reference clock for SuperSpeed (digital) phy, sometimes is
+ 24M, 25M or 27M, depended on platform.
+ "da_ref": the reference clock of analog phy, used if the clocks
+ of analog and digital phys are separated, otherwise uses
+ "ref" clock only if needed.
+
Example:
u3phy2: usb-phy at 1a244000 {
@@ -84,3 +96,49 @@ usb30: usb at 11270000 {
phy-names = "usb2-0", "usb3-0";
...
};
+
+Layout differences of banks between TPHY V1 and V2
+-------------------------------------------------------------
+IP V1:
+port offset bank
+shared 0x0000 SPLLC
+ 0x0100 FMREG
+u2 port0 0x0800 U2PHY_COM
+u3 port0 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 U2PHY_COM
+u3 port1 0x1100 U3PHYD
+ 0x1200 U3PHYD_BANK2
+ 0x1300 U3PHYA
+ 0x1400 U3PHYA_DA
+u2 port2 0x1800 U2PHY_COM
+ ...
+
+IP V2:
+port offset bank
+u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+u3 port0 0x0700 SPLLC
+ 0x0800 CHIP
+ 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+u3 port1 0x1700 SPLLC
+ 0x1800 CHIP
+ 0x1900 U3PHYD
+ 0x1a00 U3PHYD_BANK2
+ 0x1b00 U3PHYA
+ 0x1c00 U3PHYA_DA
+u2 port2 0x2000 MISC
+ ...
+
+ SPLLC shared by u3 ports and FMREG shared by u2 ports on
+TPHY V1 are put back into each port; a new bank MISC for
+u2 ports and CHIP for u3 ports are added on TPHY V2.
1. add the address mapping related properties; 2. make "ref" clock optional, and add optional clock "da_ref"; 3. add the banks layout of TPHY V1 and V2; Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com> --- v2~v3: no changes --- doc/device-tree-bindings/phy/phy-mtk-tphy.txt | 78 ++++++++++++++++--- 1 file changed, 68 insertions(+), 10 deletions(-)