@@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
stm32mp157c-ev1.dtb \
- stm32mp15xx-dhcom-pdk2.dtb
+ stm32mp15xx-dhcom-pdk2.dtb \
+ stm32mp15xx-dhcor-avenger96.dtb
dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
@@ -4,422 +4,5 @@
* Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
*/
-/dts-v1/;
-
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
- model = "Arrow Electronics STM32MP157A Avenger96 board";
- compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
- aliases {
- ethernet0 = ðernet0;
- mmc0 = &sdmmc1;
- serial0 = &uart4;
- serial1 = &uart7;
- spi0 = &qspi;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory at c0000000 {
- device_type = "memory";
- reg = <0xc0000000 0x40000000>;
- };
-
- led {
- compatible = "gpio-leds";
- led1 {
- label = "green:user1";
- gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led2 {
- label = "green:user2";
- gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led3 {
- label = "green:user3";
- gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- led4 {
- label = "green:user3";
- gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- panic-indicator;
- };
-
- led5 {
- label = "yellow:wifi";
- gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tx";
- default-state = "off";
- };
-
- led6 {
- label = "blue:bt";
- gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "bluetooth-power";
- default-state = "off";
- };
- };
-
- sd_switch: regulator-sd_switch {
- compatible = "regulator-gpio";
- regulator-name = "sd_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
- regulator-type = "voltage";
- regulator-always-on;
-
- gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1>,
- <2900000 0x0>;
- };
-
- /* Enpirion EP3A8LQI U2 on the DHCOR */
- vdd_io: regulator-buck-io {
- compatible = "regulator-fixed";
- regulator-name = "buck-io";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_b>;
- pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
- phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- phy0: ethernet-phy at 7 {
- reg = <7>;
- };
- };
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_b>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-
- pmic: stpmic at 33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- st,main-control-register = <0x04>;
- st,vin-control-register = <0xc0>;
- st,usb-control-register = <0x30>;
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- regulator-always-on;
- st,mask_reset;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- interrupt-parent = <&pmic>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- interrupt-parent = <&pmic>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO4 0>;
- interrupt-parent = <&pmic>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- interrupt-parent = <&pmic>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- interrupt-parent = <&pmic>;
- regulator-enable-ramp-delay = <300000>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- interrupt-parent = <&pmic>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- interrupt-parent = <&pmic>;
- regulator-active-discharge = <1>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- interrupt-parent = <&pmic>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- eeprom at 53 {
- compatible = "atmel,24c02";
- reg = <0x53>;
- pagesize = <16>;
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd_io>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: spi-flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
- cd-gpios = <&gpioi 8 GPIO_ACTIVE_LOW>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- sd-uhs-sdr104;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- vqmmc-supply = <&sd_switch>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
- non-removable;
- no-sd;
- no-sdio;
- st,neg-edge;
- bus-width = <8>;
- vmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&spi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-};
-
-&uart4 {
- /* On Low speed expansion header */
- label = "LS-UART1";
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
- status = "okay";
-};
-
-&uart7 {
- /* On Low speed expansion header */
- label = "LS-UART0";
- pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- phy-names = "usb";
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "peripheral";
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+/* This is kept for backward compatibility and will be removed */
+#include "stm32mp15xx-dhcor-avenger96.dts"
new file mode 100644
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex at denx.de>
+ */
+
+#include "stm32mp15xx-dhcor-u-boot.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &sdmmc1;
+ mmc1 = &sdmmc2;
+ usb0 = &usbotg_hs;
+ };
+
+ config {
+ u-boot,boot-led = "led1";
+ u-boot,error-led = "led4";
+ };
+};
+
+&sdmmc1 {
+ u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc1_dir_pins_b {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2 {
+ u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc2_d47_pins_b {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_b {
+ u-boot,dm-pre-reloc;
+ pins1 {
+ u-boot,dm-pre-reloc;
+ };
+ pins2 {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&usbotg_hs {
+ u-boot,force-b-session-valid;
+ hnp-srp-disable;
+};
new file mode 100644
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex at denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp15xx-dhcor.dtsi"
+#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
+
+/ {
+ model = "Arrow Electronics STM32MP15xx Avenger96 board";
+ compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
+
+ aliases {
+ eeprom0 = &eeprom0;
+ ethernet0 = ðernet0;
+ mmc0 = &sdmmc1;
+ serial0 = &uart4;
+ serial1 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ led {
+ compatible = "gpio-leds";
+ led1 {
+ label = "green:user1";
+ gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led2 {
+ label = "green:user2";
+ gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ led3 {
+ label = "green:user3";
+ gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ led4 {
+ label = "green:user3";
+ gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ default-state = "off";
+ panic-indicator;
+ };
+
+ led5 {
+ label = "yellow:wifi";
+ gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ led6 {
+ label = "blue:bt";
+ gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1>,
+ <2900000 0x0>;
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_b>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+ phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy at 7 {
+ reg = <7>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_b>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2c4 {
+ eeprom0: eeprom at 53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+ disable-wp;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <8>;
+ vmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&uart4 {
+ /* On Low speed expansion header */
+ label = "LS-UART1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ /* On Low speed expansion header */
+ label = "LS-UART0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbotg_hs {
+ dr_mode = "peripheral";
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
similarity index 75%
rename from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
@@ -4,25 +4,13 @@
*
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
* Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex at denx.de>
*/
#include <dt-bindings/clock/stm32mp1-clksrc.h>
#include "stm32mp157-u-boot.dtsi"
#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
-/ {
- aliases {
- mmc0 = &sdmmc1;
- mmc1 = &sdmmc2;
- usb0 = &usbotg_hs;
- };
-
- config {
- u-boot,boot-led = "led1";
- u-boot,error-led = "led4";
- };
-};
-
&i2c4 {
u-boot,dm-pre-reloc;
};
@@ -38,6 +26,10 @@
u-boot,dm-pre-reloc;
};
+&qspi {
+ u-boot,dm-spl;
+};
+
&rcc {
st,clksrc = <
CLK_MPU_PLL1P
@@ -139,67 +131,6 @@
};
};
-&sdmmc1 {
- u-boot,dm-spl;
-};
-
-&sdmmc1_b4_pins_a {
- u-boot,dm-spl;
- pins {
- u-boot,dm-spl;
- };
-};
-
-&sdmmc1_dir_pins_b {
- u-boot,dm-spl;
- pins1 {
- u-boot,dm-spl;
- };
- pins2 {
- u-boot,dm-spl;
- };
-};
-
-&sdmmc2 {
- u-boot,dm-spl;
-};
-
-&sdmmc2_b4_pins_a {
- u-boot,dm-spl;
- pins1 {
- u-boot,dm-spl;
- };
- pins2 {
- u-boot,dm-spl;
- };
-};
-
-&sdmmc2_d47_pins_b {
- u-boot,dm-spl;
- pins {
- u-boot,dm-spl;
- };
-};
-
-&uart4 {
- u-boot,dm-pre-reloc;
-};
-
-&uart4_pins_b {
- u-boot,dm-pre-reloc;
- pins1 {
- u-boot,dm-pre-reloc;
- };
- pins2 {
- u-boot,dm-pre-reloc;
- };
-};
-
-&usbotg_hs {
- u-boot,force-b-session-valid;
- hnp-srp-disable;
-};
-
&v3v3 {
regulator-always-on;
};
new file mode 100644
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex at denx.de>
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ aliases {
+ spi0 = &qspi;
+ };
+
+ memory at c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x40000000>;
+ };
+
+ /* Enpirion EP3A8LQI U2 on the DHCOR */
+ vdd_io: regulator-buck-io {
+ compatible = "regulator-fixed";
+ regulator-name = "buck-io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vdd>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic at 33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ st,main-control-register = <0x04>;
+ st,vin-control-register = <0xc0>;
+ st,usb-control-register = <0x30>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo1-supply = <&v3v3>;
+ ldo2-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo5-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-always-on;
+ st,mask_reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ vdda: ldo1 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ v2v8: ldo2 {
+ regulator-name = "v2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vdd_sd: ldo5 {
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ interrupt-parent = <&pmic>;
+ regulator-boot-on;
+ };
+
+ v1v8: ldo6 {
+ regulator-name = "v1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ interrupt-parent = <&pmic>;
+ regulator-enable-ramp-delay = <300000>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ interrupt-parent = <&pmic>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ interrupt-parent = <&pmic>;
+ regulator-active-discharge = <1>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ interrupt-parent = <&pmic>;
+ regulator-active-discharge = <1>;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd_io>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+ pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: spi-flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
@@ -43,11 +43,11 @@ And the necessary drivers
Currently the following boards are supported:
- + stm32mp157a-avenger96.dts
+ stm32mp157a-dk1.dts
+ stm32mp157c-dk2.dts
+ stm32mp157c-ed1.dts
+ stm32mp157c-ev1.dts
+ + stm32mp15xx-dhcor-avenger96.dts
Boot Sequences
--------------
@@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
+ stm32mp157c-dk2
-+ avenger96: Avenger96 board from Arrow Electronics
++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
- + stm32mp157a-avenger96
+ + stm32mp15xx-dhcor-avenger96
Build Procedure
---------------
@@ -229,7 +229,7 @@ Build Procedure
# export KBUILD_OUTPUT=stm32mp15_basic
# make stm32mp15_basic_defconfig
- # make DEVICE_TREE=stm32mp157a-avenger96 all
+ # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
6. Output files
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily. It is also highly recommended to configure the board for the DHCOM make stm32mp15_dhcom_basic_defconfig make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM. Signed-off-by: Marek Vasut <marex at denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org> Cc: Patrick Delaunay <patrick.delaunay at st.com> Cc: Patrice Chotard <patrice.chotard at st.com> --- V2: No change V3: No change --- arch/arm/dts/Makefile | 3 +- arch/arm/dts/stm32mp157a-avenger96.dts | 421 +----------------- .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi | 80 ++++ arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 211 +++++++++ ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} | 79 +--- arch/arm/dts/stm32mp15xx-dhcor.dtsi | 231 ++++++++++ doc/board/st/stm32mp1.rst | 8 +- 7 files changed, 535 insertions(+), 498 deletions(-) create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%) create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsi