diff mbox series

[v3,3/5] i2c: aspeed: Mask IRQ status to relevant bits

Message ID 20200909203059.23427-4-eajames@linux.ibm.com
State Accepted
Commit 1a1d6db23ddacde0b15ea589e9103373e05af8de
Headers show
Series None | expand

Commit Message

Eddie James Sept. 9, 2020, 8:30 p.m. UTC
Mask the IRQ status to only the bits that the driver checks. This
prevents excessive driver warnings when operating in slave mode
when additional bits are set that the driver doesn't handle.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
---
 drivers/i2c/busses/i2c-aspeed.c | 2 ++
 1 file changed, 2 insertions(+)

Comments

Wolfram Sang Sept. 10, 2020, 6:18 a.m. UTC | #1
On Wed, Sep 09, 2020 at 03:30:57PM -0500, Eddie James wrote:
> Mask the IRQ status to only the bits that the driver checks. This
> prevents excessive driver warnings when operating in slave mode
> when additional bits are set that the driver doesn't handle.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> Reviewed-by: Tao Ren <rentao.bupt@gmail.com>

I reconsidered and applied it now because this helps whenever slave mode
is used. So, applied to for-current, thanks!
Eddie James Sept. 10, 2020, 1:55 p.m. UTC | #2
On 9/10/20 4:00 AM, Brendan Higgins wrote:
> On Wed, Sep 9, 2020 at 1:31 PM Eddie James <eajames@linux.ibm.com> wrote:
>> Mask the IRQ status to only the bits that the driver checks. This
>> prevents excessive driver warnings when operating in slave mode
>> when additional bits are set that the driver doesn't handle.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
> Sorry, looks like I didn't get my comment in in time.
>
> Looks good in principle. One minor comment below:
>
>> ---
>>   drivers/i2c/busses/i2c-aspeed.c | 2 ++
>>   1 file changed, 2 insertions(+)
>>
>> diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
>> index 31268074c422..724bf30600d6 100644
>> --- a/drivers/i2c/busses/i2c-aspeed.c
>> +++ b/drivers/i2c/busses/i2c-aspeed.c
>> @@ -69,6 +69,7 @@
>>    * These share bit definitions, so use the same values for the enable &
>>    * status bits.
>>    */
>> +#define ASPEED_I2CD_INTR_RECV_MASK                     0xf000ffff
> Could we define ASPEED_I2CD_INTR_RECV_MASK to be ASPEED_I2CD_INTR_ALL ?


That was my original thought... there is another define for that already 
a few lines down though.


Thanks,

Eddie


>
>>   #define ASPEED_I2CD_INTR_SDA_DL_TIMEOUT                        BIT(14)
>>   #define ASPEED_I2CD_INTR_BUS_RECOVER_DONE              BIT(13)
>>   #define ASPEED_I2CD_INTR_SLAVE_MATCH                   BIT(7)
>> @@ -604,6 +605,7 @@ static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
>>          writel(irq_received & ~ASPEED_I2CD_INTR_RX_DONE,
>>                 bus->base + ASPEED_I2C_INTR_STS_REG);
>>          readl(bus->base + ASPEED_I2C_INTR_STS_REG);
>> +       irq_received &= ASPEED_I2CD_INTR_RECV_MASK;
>>          irq_remaining = irq_received;
>>
>>   #if IS_ENABLED(CONFIG_I2C_SLAVE)
>> --
>> 2.26.2
>>
diff mbox series

Patch

diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index 31268074c422..724bf30600d6 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c
@@ -69,6 +69,7 @@ 
  * These share bit definitions, so use the same values for the enable &
  * status bits.
  */
+#define ASPEED_I2CD_INTR_RECV_MASK			0xf000ffff
 #define ASPEED_I2CD_INTR_SDA_DL_TIMEOUT			BIT(14)
 #define ASPEED_I2CD_INTR_BUS_RECOVER_DONE		BIT(13)
 #define ASPEED_I2CD_INTR_SLAVE_MATCH			BIT(7)
@@ -604,6 +605,7 @@  static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
 	writel(irq_received & ~ASPEED_I2CD_INTR_RX_DONE,
 	       bus->base + ASPEED_I2C_INTR_STS_REG);
 	readl(bus->base + ASPEED_I2C_INTR_STS_REG);
+	irq_received &= ASPEED_I2CD_INTR_RECV_MASK;
 	irq_remaining = irq_received;
 
 #if IS_ENABLED(CONFIG_I2C_SLAVE)