@@ -116,7 +116,6 @@
switch0: ksz8563@0 {
compatible = "microchip,ksz8563";
reg = <0>;
- phy-mode = "mii";
reset-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_LOW>;
spi-max-frequency = <500000>;
@@ -140,6 +139,7 @@
reg = <2>;
label = "cpu";
ethernet = <&macb0>;
+ phy-mode = "mii";
fixed-link {
speed = <100>;
full-duplex;
@@ -932,11 +932,18 @@ static void ksz8795_port_setup(struct ksz_device *dev, int port, bool cpu_port)
ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true);
if (cpu_port) {
+ if (!p->interface && dev->compat_interface) {
+ dev_warn(dev->dev,
+ "Using legacy switch \"phy-mode\" missing on port %d node. Please update your device tree.\n",
+ port);
+ p->interface = dev->compat_interface;
+ }
+
/* Configure MII interface for proper network communication. */
ksz_read8(dev, REG_PORT_5_CTRL_6, &data8);
data8 &= ~PORT_INTERFACE_TYPE;
data8 &= ~PORT_GMII_1GPS_MODE;
- switch (dev->interface) {
+ switch (p->interface) {
case PHY_INTERFACE_MODE_MII:
p->phydev.speed = SPEED_100;
break;
@@ -952,11 +959,11 @@ static void ksz8795_port_setup(struct ksz_device *dev, int port, bool cpu_port)
default:
data8 &= ~PORT_RGMII_ID_IN_ENABLE;
data8 &= ~PORT_RGMII_ID_OUT_ENABLE;
- if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
- dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+ if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ p->interface == PHY_INTERFACE_MODE_RGMII_RXID)
data8 |= PORT_RGMII_ID_IN_ENABLE;
- if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
- dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+ if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ p->interface == PHY_INTERFACE_MODE_RGMII_TXID)
data8 |= PORT_RGMII_ID_OUT_ENABLE;
data8 |= PORT_GMII_1GPS_MODE;
data8 |= PORT_INTERFACE_RGMII;
@@ -1208,7 +1208,7 @@ static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
/* configure MAC to 1G & RGMII mode */
ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8);
- switch (dev->interface) {
+ switch (p->interface) {
case PHY_INTERFACE_MODE_MII:
ksz9477_set_xmii(dev, 0, &data8);
ksz9477_set_gbit(dev, false, &data8);
@@ -1229,11 +1229,11 @@ static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
ksz9477_set_gbit(dev, true, &data8);
data8 &= ~PORT_RGMII_ID_IG_ENABLE;
data8 &= ~PORT_RGMII_ID_EG_ENABLE;
- if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
- dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
+ if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ p->interface == PHY_INTERFACE_MODE_RGMII_RXID)
data8 |= PORT_RGMII_ID_IG_ENABLE;
- if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
- dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
+ if (p->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ p->interface == PHY_INTERFACE_MODE_RGMII_TXID)
data8 |= PORT_RGMII_ID_EG_ENABLE;
p->phydev.speed = SPEED_1000;
break;
@@ -1269,23 +1269,31 @@ static void ksz9477_config_cpu_port(struct dsa_switch *ds)
dev->cpu_port = i;
dev->host_mask = (1 << dev->cpu_port);
dev->port_mask |= dev->host_mask;
+ p = &dev->ports[i];
/* Read from XMII register to determine host port
* interface. If set specifically in device tree
* note the difference to help debugging.
*/
interface = ksz9477_get_interface(dev, i);
- if (!dev->interface)
- dev->interface = interface;
- if (interface && interface != dev->interface)
+ if (!p->interface) {
+ if (dev->compat_interface) {
+ dev_warn(dev->dev,
+ "Using legacy switch \"phy-mode\" missing on port %d node. Please update your device tree.\n",
+ i);
+ p->interface = dev->compat_interface;
+ } else {
+ p->interface = interface;
+ }
+ }
+ if (interface && interface != p->interface)
dev_info(dev->dev,
"use %s instead of %s\n",
- phy_modes(dev->interface),
+ phy_modes(p->interface),
phy_modes(interface));
/* enable cpu port */
ksz9477_port_setup(dev, i, true);
- p = &dev->ports[dev->cpu_port];
p->vid_member = dev->port_mask;
p->on = 1;
}
@@ -388,6 +388,8 @@ int ksz_switch_register(struct ksz_device *dev,
const struct ksz_dev_ops *ops)
{
phy_interface_t interface;
+ struct device_node *port;
+ unsigned int port_num;
int ret;
if (dev->pdata)
@@ -421,10 +423,19 @@ int ksz_switch_register(struct ksz_device *dev,
/* Host port interface will be self detected, or specifically set in
* device tree.
*/
+ for (port_num = 0; port_num < dev->port_cnt; ++port_num)
+ dev->ports[port_num].interface = PHY_INTERFACE_MODE_NA;
if (dev->dev->of_node) {
ret = of_get_phy_mode(dev->dev->of_node, &interface);
if (ret == 0)
- dev->interface = interface;
+ dev->compat_interface = interface;
+ for_each_available_child_of_node(dev->dev->of_node, port) {
+ if (of_property_read_u32(port, "reg", &port_num))
+ continue;
+ if (port_num >= dev->port_cnt)
+ return -EINVAL;
+ of_get_phy_mode(port, &dev->ports[port_num].interface);
+ }
dev->synclko_125 = of_property_read_bool(dev->dev->of_node,
"microchip,synclko-125");
}
@@ -39,6 +39,7 @@ struct ksz_port {
u32 freeze:1; /* MIB counter freeze is enabled */
struct ksz_port_mib mib;
+ phy_interface_t interface;
};
struct ksz_device {
@@ -72,7 +73,7 @@ struct ksz_device {
int mib_cnt;
int mib_port_cnt;
int last_port; /* ports after that not used */
- phy_interface_t interface;
+ phy_interface_t compat_interface;
u32 regs_size;
bool phy_errata_9477;
bool synclko_125;
Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode property should be specified on port nodes. However, the microchip drivers read it from the switch node. Let the driver use the per-port property and fall back to the old location with a warning. Fix in-tree users. Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de> Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/ --- arch/arm/boot/dts/at91-sama5d2_icp.dts | 2 +- drivers/net/dsa/microchip/ksz8795.c | 17 +++++++++++----- drivers/net/dsa/microchip/ksz9477.c | 28 +++++++++++++++++--------- drivers/net/dsa/microchip/ksz_common.c | 13 +++++++++++- drivers/net/dsa/microchip/ksz_common.h | 3 ++- 5 files changed, 45 insertions(+), 18 deletions(-) Changes since v1: * Preserve the reverse christmas tree ordering of local variables. Reported by David Miller. Reason for resending v1: * While Andrew Lunn agreed to the semantic change, he found the implementation unnecessarily complex. He suggested going without a per-port interface attribute, but that happened to not work out. The information of which port will become the cpu port is only realized in a later initialization step. There were no further replies, so here goes a v2 with minimal changes. Helmut