diff mbox series

[v4,net-next,2/2] powerpc: dts: t1040rdb: add ports for Seville Ethernet switch

Message ID 20201002134106.3485970-3-vladimir.oltean@nxp.com
State Superseded
Headers show
Series Add Seville Ethernet switch to T1040RDB | expand

Commit Message

Vladimir Oltean Oct. 2, 2020, 1:41 p.m. UTC 
Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.

A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
Changes in v4:
- Retargeted to net-next.
- Fixed the port labels (ETH5 was ETH4, ETH7 was ETH6, ETH9 was ETH8,
  ETH11 was ETH10).

Changes in v3:
Renamed interfaces from swpN to ETHN, as per Andrew Lunn's suggestion.

Changes in v2:
Use the existing way of accessing the mdio bus and not labels.

 arch/powerpc/boot/dts/fsl/t1040rdb.dts | 107 +++++++++++++++++++++++++
 1 file changed, 107 insertions(+)
diff mbox series

Patch

diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb.dts b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
index 65ff34c49025..af0c8a6f5613 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -64,6 +64,40 @@  mdio@fc000 {
 				phy_sgmii_2: ethernet-phy@3 {
 					reg = <0x03>;
 				};
+
+				/* VSC8514 QSGMII PHY */
+				phy_qsgmii_0: ethernet-phy@4 {
+					reg = <0x4>;
+				};
+
+				phy_qsgmii_1: ethernet-phy@5 {
+					reg = <0x5>;
+				};
+
+				phy_qsgmii_2: ethernet-phy@6 {
+					reg = <0x6>;
+				};
+
+				phy_qsgmii_3: ethernet-phy@7 {
+					reg = <0x7>;
+				};
+
+				/* VSC8514 QSGMII PHY */
+				phy_qsgmii_4: ethernet-phy@8 {
+					reg = <0x8>;
+				};
+
+				phy_qsgmii_5: ethernet-phy@9 {
+					reg = <0x9>;
+				};
+
+				phy_qsgmii_6: ethernet-phy@a {
+					reg = <0xa>;
+				};
+
+				phy_qsgmii_7: ethernet-phy@b {
+					reg = <0xb>;
+				};
 			};
 		};
 	};
@@ -76,3 +110,76 @@  cpld@3,0 {
 };
 
 #include "t1040si-post.dtsi"
+
+&seville_switch {
+	status = "okay";
+};
+
+&seville_port0 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_0>;
+	phy-mode = "qsgmii";
+	label = "ETH5";
+	status = "okay";
+};
+
+&seville_port1 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_1>;
+	phy-mode = "qsgmii";
+	label = "ETH4";
+	status = "okay";
+};
+
+&seville_port2 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_2>;
+	phy-mode = "qsgmii";
+	label = "ETH7";
+	status = "okay";
+};
+
+&seville_port3 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_3>;
+	phy-mode = "qsgmii";
+	label = "ETH6";
+	status = "okay";
+};
+
+&seville_port4 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_4>;
+	phy-mode = "qsgmii";
+	label = "ETH9";
+	status = "okay";
+};
+
+&seville_port5 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_5>;
+	phy-mode = "qsgmii";
+	label = "ETH8";
+	status = "okay";
+};
+
+&seville_port6 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_6>;
+	phy-mode = "qsgmii";
+	label = "ETH11";
+	status = "okay";
+};
+
+&seville_port7 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_7>;
+	phy-mode = "qsgmii";
+	label = "ETH10";
+	status = "okay";
+};
+
+&seville_port8 {
+	ethernet = <&enet0>;
+	status = "okay";
+};