diff mbox

[v2] mmc: core: Try other signal levels during power up

Message ID 1398375866-8898-1-git-send-email-tim.kryger@linaro.org
State New
Headers show

Commit Message

Tim Kryger April 24, 2014, 9:44 p.m. UTC
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host.  Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.

In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11.  A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.

It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted.  This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.

Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
---

Changes since v1:
  - Eliminated temporary err variable and added debug output

 drivers/mmc/core/core.c |    9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

Comments

Ulf Hansson April 25, 2014, 8:16 a.m. UTC | #1
On 24 April 2014 23:44, Tim Kryger <tim.kryger@linaro.org> wrote:
> The eMMC signalling voltage is determined by VCCQ which is provided to
> the card by the host.  Signalling is not required to begin at 3.3v and,
> if the host and card both support a particular VCC/VCCQ combination, it
> can be used immediately.
>
> In contrast, SD Cards must begin with 3.3v signalling and may switch to
> a lower voltage signalling if instructed to do so in CMD11.  A message
> is required to coordinate this operation because the card only receives
> a 3.3v VDD and must know when to use the 1.8v produced by its internal
> regulator.
>
> It makes sense for the core to begin with 3.3v signalling but when that
> can't be set, 1.8v and 1.2v signalling also should be attempted.  This
> is especially important when an external regulator with a limited range
> is used to supply VCCQ to an eMMC part.
>
> Signed-off-by: Tim Kryger <tim.kryger@linaro.org>

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>

> ---
>
> Changes since v1:
>   - Eliminated temporary err variable and added debug output
>
>  drivers/mmc/core/core.c |    9 +++++++--
>  1 file changed, 7 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
> index acbc3f2..72926a9 100644
> --- a/drivers/mmc/core/core.c
> +++ b/drivers/mmc/core/core.c
> @@ -1533,8 +1533,13 @@ void mmc_power_up(struct mmc_host *host, u32 ocr)
>         host->ios.timing = MMC_TIMING_LEGACY;
>         mmc_set_ios(host);
>
> -       /* Set signal voltage to 3.3V */
> -       __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
> +       /* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
> +       if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
> +               dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n");
> +       else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180) == 0)
> +               dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n");
> +       else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120) == 0)
> +               dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n");
>
>         /*
>          * This delay should be sufficient to allow the power supply
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index acbc3f2..72926a9 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1533,8 +1533,13 @@  void mmc_power_up(struct mmc_host *host, u32 ocr)
 	host->ios.timing = MMC_TIMING_LEGACY;
 	mmc_set_ios(host);
 
-	/* Set signal voltage to 3.3V */
-	__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
+	/* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
+	if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
+		dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n");
+	else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180) == 0)
+		dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n");
+	else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120) == 0)
+		dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n");
 
 	/*
 	 * This delay should be sufficient to allow the power supply