@@ -2,7 +2,7 @@
/*
* Device Tree Source for J721E SoC Family MCU/WAKEUP Domain peripherals
*
- * Copyright (C) 2016-2019 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2016-2020 Texas Instruments Incorporated - https://www.ti.com/
*/
&cbass_mcu_wakeup {
@@ -353,4 +353,44 @@ cpts@3d000 {
ti,cpts-periodic-outputs = <2>;
};
};
+
+ mcu_r5fss0: r5fss@41000000 {
+ compatible = "ti,j721e-r5fss";
+ ti,cluster-mode = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x41000000 0x00 0x41000000 0x20000>,
+ <0x41400000 0x00 0x41400000 0x20000>;
+ power-domains = <&k3_pds 249 TI_SCI_PD_EXCLUSIVE>;
+
+ mcu_r5fss0_core0: r5f@41000000 {
+ compatible = "ti,j721e-r5f";
+ reg = <0x41000000 0x00008000>,
+ <0x41010000 0x00008000>;
+ reg-names = "atcm", "btcm";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <250>;
+ ti,sci-proc-ids = <0x01 0xff>;
+ resets = <&k3_reset 250 1>;
+ firmware-name = "j7-mcu-r5f0_0-fw";
+ ti,atcm-enable = <1>;
+ ti,btcm-enable = <1>;
+ ti,loczrama = <1>;
+ };
+
+ mcu_r5fss0_core1: r5f@41400000 {
+ compatible = "ti,j721e-r5f";
+ reg = <0x41400000 0x00008000>,
+ <0x41410000 0x00008000>;
+ reg-names = "atcm", "btcm";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <251>;
+ ti,sci-proc-ids = <0x02 0xff>;
+ resets = <&k3_reset 251 1>;
+ firmware-name = "j7-mcu-r5f0_1-fw";
+ ti,atcm-enable = <1>;
+ ti,btcm-enable = <1>;
+ ti,loczrama = <1>;
+ };
+ };
};
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS) subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within the MCU domain, and the remaining two clusters are present in the MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be configured at boot time to be either run in a LockStep mode or in an Asymmetric Multi Processing (AMP) fashion in Split-mode. These subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal memories for each core split between two banks - ATCM and BTCM (further interleaved into two banks). There are some IP integration differences from standard Arm R5 clusters such as the absence of an ACP port, presence of an additional TI-specific Region Address Translater (RAT) module for translating 32-bit CPU addresses into larger system bus addresses etc. Add the DT node for the MCU domain R5F cluster/subsystem, the two R5F cores are added as child nodes to the main cluster/subsystem node. The cluster is configured to run in LockStep mode by default, with the ATCMs enabled to allow the R5 cores to execute code from DDR with boot-strapping code from ATCM. The inter-processor communication between the main A72 cores and these processors is achieved through shared memory and Mailboxes. The following firmware names are used by default for these cores, and can be overridden in a board dts file if needed: MCU R5FSS0 Core0: j7-mcu-r5f0_0-fw (both in LockStep and Split modes) MCU R5FSS0 Core1: j7-mcu-r5f0_1-fw (needed only in Split mode) Signed-off-by: Suman Anna <s-anna@ti.com> --- .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 42 ++++++++++++++++++- 1 file changed, 41 insertions(+), 1 deletion(-)