diff mbox series

[v3,5/5] arm64: dts: ti: Add support for AM642 EVM

Message ID 20210120202532.9011-6-d-gerlach@ti.com
State Superseded
Headers show
Series arm64: Initial support for Texas Instruments AM642 Platform | expand

Commit Message

Dave Gerlach Jan. 20, 2021, 8:25 p.m. UTC
The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.

Introduce support for the AM642 EVM to enable mmc boot, including
enabling UART and I2C on the board.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
---
 arch/arm64/boot/dts/ti/Makefile         |   2 +
 arch/arm64/boot/dts/ti/k3-am642-evm.dts | 246 ++++++++++++++++++++++++
 2 files changed, 248 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am642-evm.dts

Comments

Suman Anna Jan. 25, 2021, 4:44 p.m. UTC | #1
On 1/20/21 2:25 PM, Dave Gerlach wrote:
> The AM642 EValuation Module (EVM) is a board that provides access to

> various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,

> CPSW Ethernet, ADC, and more.

> 

> Introduce support for the AM642 EVM to enable mmc boot, including

> enabling UART and I2C on the board.

> 

> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

> Signed-off-by: Suman Anna <s-anna@ti.com>

> Signed-off-by: Nishanth Menon <nm@ti.com>

> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>

> ---

>  arch/arm64/boot/dts/ti/Makefile         |   2 +

>  arch/arm64/boot/dts/ti/k3-am642-evm.dts | 246 ++++++++++++++++++++++++

>  2 files changed, 248 insertions(+)

>  create mode 100644 arch/arm64/boot/dts/ti/k3-am642-evm.dts

> 

> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile

> index 65506f21ba30..c687739e2bca 100644

> --- a/arch/arm64/boot/dts/ti/Makefile

> +++ b/arch/arm64/boot/dts/ti/Makefile

> @@ -11,3 +11,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb

>  dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb

>  

>  dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb

> +

> +dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb


nit, please update the copyright year to include 2021 on this file.

regards
Suman

> diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts

> new file mode 100644

> index 000000000000..1f1787750fef

> --- /dev/null

> +++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts

> @@ -0,0 +1,246 @@

> +// SPDX-License-Identifier: GPL-2.0

> +/*

> + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/

> + */

> +

> +/dts-v1/;

> +

> +#include <dt-bindings/leds/common.h>

> +#include "k3-am642.dtsi"

> +

> +/ {

> +	compatible =  "ti,am642-evm", "ti,am642";

> +	model = "Texas Instruments AM642 EVM";

> +

> +	chosen {

> +		stdout-path = "serial2:115200n8";

> +		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";

> +	};

> +

> +	memory@80000000 {

> +		device_type = "memory";

> +		/* 2G RAM */

> +		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;

> +

> +	};

> +

> +	reserved-memory {

> +		#address-cells = <2>;

> +		#size-cells = <2>;

> +		ranges;

> +

> +		secure_ddr: optee@9e800000 {

> +			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */

> +			alignment = <0x1000>;

> +			no-map;

> +		};

> +	};

> +

> +	evm_12v0: fixedregulator-evm12v0 {

> +		/* main DC jack */

> +		compatible = "regulator-fixed";

> +		regulator-name = "evm_12v0";

> +		regulator-min-microvolt = <12000000>;

> +		regulator-max-microvolt = <12000000>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	vsys_5v0: fixedregulator-vsys5v0 {

> +		/* output of LM5140 */

> +		compatible = "regulator-fixed";

> +		regulator-name = "vsys_5v0";

> +		regulator-min-microvolt = <5000000>;

> +		regulator-max-microvolt = <5000000>;

> +		vin-supply = <&evm_12v0>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	vsys_3v3: fixedregulator-vsys3v3 {

> +		/* output of LM5140 */

> +		compatible = "regulator-fixed";

> +		regulator-name = "vsys_3v3";

> +		regulator-min-microvolt = <3300000>;

> +		regulator-max-microvolt = <3300000>;

> +		vin-supply = <&evm_12v0>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	vdd_mmc1: fixed-regulator-sd {

> +		/* TPS2051BD */

> +		compatible = "regulator-fixed";

> +		regulator-name = "vdd_mmc1";

> +		regulator-min-microvolt = <3300000>;

> +		regulator-max-microvolt = <3300000>;

> +		regulator-boot-on;

> +		enable-active-high;

> +		vin-supply = <&vsys_3v3>;

> +		gpio = <&exp1 6 GPIO_ACTIVE_HIGH>;

> +	};

> +

> +	vddb: fixedregulator-vddb {

> +		compatible = "regulator-fixed";

> +		regulator-name = "vddb_3v3_display";

> +		regulator-min-microvolt = <3300000>;

> +		regulator-max-microvolt = <3300000>;

> +		vin-supply = <&vsys_3v3>;

> +		regulator-always-on;

> +		regulator-boot-on;

> +	};

> +

> +	leds {

> +		compatible = "gpio-leds";

> +

> +		led-0 {

> +			label = "am64-evm:red:heartbeat";

> +			gpios = <&exp1 16 GPIO_ACTIVE_HIGH>;

> +			linux,default-trigger = "heartbeat";

> +			function = LED_FUNCTION_HEARTBEAT;

> +			default-state = "off";

> +		};

> +	};

> +};

> +

> +&main_pmx0 {

> +	main_mmc1_pins_default: main-mmc1-pins-default {

> +		pinctrl-single,pins = <

> +			AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */

> +			AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */

> +			AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */

> +			AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */

> +			AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */

> +			AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */

> +			AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */

> +			AM64X_IOPAD(0x029c, PIN_INPUT, 0) /* (C20) MMC1_SDWP */

> +			AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */

> +		>;

> +	};

> +

> +	main_uart0_pins_default: main-uart0-pins-default {

> +		pinctrl-single,pins = <

> +			AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */

> +			AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */

> +			AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */

> +			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */

> +		>;

> +	};

> +

> +	main_i2c1_pins_default: main-i2c1-pins-default {

> +		pinctrl-single,pins = <

> +			AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */

> +			AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */

> +		>;

> +	};

> +};

> +

> +&main_uart0 {

> +	pinctrl-names = "default";

> +	pinctrl-0 = <&main_uart0_pins_default>;

> +};

> +

> +/* main_uart1 is reserved for firmware usage */

> +&main_uart1 {

> +	status = "reserved";

> +};

> +

> +&main_uart2 {

> +	status = "disabled";

> +};

> +

> +&main_uart3 {

> +	status = "disabled";

> +};

> +

> +&main_uart4 {

> +	status = "disabled";

> +};

> +

> +&main_uart5 {

> +	status = "disabled";

> +};

> +

> +&main_uart6 {

> +	status = "disabled";

> +};

> +

> +&mcu_uart0 {

> +	status = "disabled";

> +};

> +

> +&mcu_uart1 {

> +	status = "disabled";

> +};

> +

> +&main_i2c1 {

> +	pinctrl-names = "default";

> +	pinctrl-0 = <&main_i2c1_pins_default>;

> +	clock-frequency = <400000>;

> +

> +	exp1: gpio@22 {

> +		compatible = "ti,tca6424";

> +		reg = <0x22>;

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +		gpio-line-names = "GPIO_eMMC_RSTn", "CAN_MUX_SEL",

> +				  "GPIO_CPSW1_RST", "GPIO_RGMII1_RST",

> +				  "GPIO_RGMII2_RST", "GPIO_PCIe_RST_OUT",

> +				  "MMC1_SD_EN", "FSI_FET_SEL",

> +				  "MCAN0_STB_3V3", "MCAN1_STB_3V3",

> +				  "CPSW_FET_SEL", "CPSW_FET2_SEL",

> +				  "PRG1_RGMII2_FET_SEL", "TEST_GPIO2",

> +				  "GPIO_OLED_RESETn", "VPP_LDO_EN",

> +				  "TEST_LED1", "TP92", "TP90", "TP88",

> +				  "TP87", "TP86", "TP89", "TP91";

> +	};

> +

> +	/* osd9616p0899-10 */

> +	display@3c {

> +		compatible = "solomon,ssd1306fb-i2c";

> +		reg = <0x3c>;

> +		reset-gpios = <&exp1 14 GPIO_ACTIVE_LOW>;

> +		vbat-supply = <&vddb>;

> +		solomon,height = <16>;

> +		solomon,width = <96>;

> +		solomon,com-seq;

> +		solomon,com-invdir;

> +		solomon,page-offset = <0>;

> +		solomon,prechargep1 = <2>;

> +		solomon,prechargep2 = <13>;

> +	};

> +};

> +

> +&mcu_i2c0 {

> +	status = "disabled";

> +};

> +

> +&mcu_i2c1 {

> +	status = "disabled";

> +};

> +

> +&mcu_spi0 {

> +	status = "disabled";

> +};

> +

> +&mcu_spi1 {

> +	status = "disabled";

> +};

> +

> +&sdhci0 {

> +	/* emmc */

> +	bus-width = <8>;

> +	non-removable;

> +	ti,driver-strength-ohm = <50>;

> +	disable-wp;

> +};

> +

> +&sdhci1 {

> +	/* SD/MMC */

> +	vmmc-supply = <&vdd_mmc1>;

> +	pinctrl-names = "default";

> +	bus-width = <4>;

> +	pinctrl-0 = <&main_mmc1_pins_default>;

> +	ti,driver-strength-ohm = <50>;

> +	disable-wp;

> +};

>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 65506f21ba30..c687739e2bca 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -11,3 +11,5 @@  dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
+
+dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
new file mode 100644
index 000000000000..1f1787750fef
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -0,0 +1,246 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "k3-am642.dtsi"
+
+/ {
+	compatible =  "ti,am642-evm", "ti,am642";
+	model = "Texas Instruments AM642 EVM";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main DC jack */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixed-regulator-sd {
+		/* TPS2051BD */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	vddb: fixedregulator-vddb {
+		compatible = "regulator-fixed";
+		regulator-name = "vddb_3v3_display";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vsys_3v3>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "am64-evm:red:heartbeat";
+			gpios = <&exp1 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+	};
+};
+
+&main_pmx0 {
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
+			AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */
+			AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */
+			AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */
+			AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */
+			AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */
+			AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */
+			AM64X_IOPAD(0x029c, PIN_INPUT, 0) /* (C20) MMC1_SDWP */
+			AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */
+		>;
+	};
+
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */
+			AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */
+			AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
+			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
+			AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */
+		>;
+	};
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+/* main_uart1 is reserved for firmware usage */
+&main_uart1 {
+	status = "reserved";
+};
+
+&main_uart2 {
+	status = "disabled";
+};
+
+&main_uart3 {
+	status = "disabled";
+};
+
+&main_uart4 {
+	status = "disabled";
+};
+
+&main_uart5 {
+	status = "disabled";
+};
+
+&main_uart6 {
+	status = "disabled";
+};
+
+&mcu_uart0 {
+	status = "disabled";
+};
+
+&mcu_uart1 {
+	status = "disabled";
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "GPIO_eMMC_RSTn", "CAN_MUX_SEL",
+				  "GPIO_CPSW1_RST", "GPIO_RGMII1_RST",
+				  "GPIO_RGMII2_RST", "GPIO_PCIe_RST_OUT",
+				  "MMC1_SD_EN", "FSI_FET_SEL",
+				  "MCAN0_STB_3V3", "MCAN1_STB_3V3",
+				  "CPSW_FET_SEL", "CPSW_FET2_SEL",
+				  "PRG1_RGMII2_FET_SEL", "TEST_GPIO2",
+				  "GPIO_OLED_RESETn", "VPP_LDO_EN",
+				  "TEST_LED1", "TP92", "TP90", "TP88",
+				  "TP87", "TP86", "TP89", "TP91";
+	};
+
+	/* osd9616p0899-10 */
+	display@3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		reg = <0x3c>;
+		reset-gpios = <&exp1 14 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&vddb>;
+		solomon,height = <16>;
+		solomon,width = <96>;
+		solomon,com-seq;
+		solomon,com-invdir;
+		solomon,page-offset = <0>;
+		solomon,prechargep1 = <2>;
+		solomon,prechargep2 = <13>;
+	};
+};
+
+&mcu_i2c0 {
+	status = "disabled";
+};
+
+&mcu_i2c1 {
+	status = "disabled";
+};
+
+&mcu_spi0 {
+	status = "disabled";
+};
+
+&mcu_spi1 {
+	status = "disabled";
+};
+
+&sdhci0 {
+	/* emmc */
+	bus-width = <8>;
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	vmmc-supply = <&vdd_mmc1>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};