| Message ID | 20210128175225.3102958-3-dmitry.baryshkov@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | Add support for Qualcomm QCA639x chips family | expand |
On Thu 28 Jan 11:52 CST 2021, Dmitry Baryshkov wrote: > Add qca6391 to device tree as a way to provide power domain to WiFi and > BT parts of the chip. > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > --- > arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 61 ++++++++++++++++++++++++ > 1 file changed, 61 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > index 8aebc3660b11..2b0c1cc9333b 100644 > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > @@ -151,6 +151,23 @@ vreg_s4a_1p8: vreg-s4a-1p8 { > regulator-max-microvolt = <1800000>; > regulator-always-on; > }; > + > + qca6391: qca6391 { > + compatible = "qcom,qca6390"; > + #power-domain-cells = <0>; > + > + vddaon-supply = <&vreg_s6a_0p95>; > + vddpmu-supply = <&vreg_s2f_0p95>; > + vddrfa1-supply = <&vreg_s2f_0p95>; > + vddrfa2-supply = <&vreg_s8c_1p3>; > + vddrfa3-supply = <&vreg_s5a_1p9>; > + vddpcie1-supply = <&vreg_s8c_1p3>; > + vddpcie2-supply = <&vreg_s5a_1p9>; > + vddio-supply = <&vreg_s4a_1p8>; > + pinctrl-names = "default", "active"; > + pinctrl-0 = <&wlan_default_state &bt_default_state>; > + pinctrl-1 = <&wlan_active_state &bt_active_state>; I dislike the use of pinctrl states for toggling the level of the gpio and would prefer that you use the gpio binding and api for this instead. > + }; > }; > > &adsp { > @@ -1013,6 +1030,28 @@ &tlmm { > "HST_WLAN_UART_TX", > "HST_WLAN_UART_RX"; > > + bt_default_state: bt-default-state { Are you sure you need to drive the BT_EN pin in order to have WiFi working? On QCA6174 I believe the "WL_EN" was actually RESET_N and BT_EN was actually "blueooth enable" - so we wired that in the bluetooth node instead. > + bt-en { > + pins = "gpio21"; > + function = "gpio"; > + > + drive-strength = <16>; > + output-low; > + bias-pull-up; > + }; > + }; > + > + bt_active_state: bt-active-state { > + bt-en { > + pins = "gpio21"; > + function = "gpio"; > + > + drive-strength = <16>; > + output-high; > + bias-pull-up; > + }; > + }; > + > lt9611_irq_pin: lt9611-irq { > pins = "gpio63"; > function = "gpio"; > @@ -1119,6 +1158,28 @@ sdc2_card_det_n: sd-card-det-n { > function = "gpio"; > bias-pull-up; > }; > + > + wlan_default_state: wlan-default-state { JFYI. You don't need this "dummy" subnode, you can put the properties directly in the state node. Regards, Bjorn > + wlan-en { > + pins = "gpio20"; > + function = "gpio"; > + > + drive-strength = <16>; > + output-low; > + bias-pull-up; > + }; > + }; > + > + wlan_active_state: wlan-active-state { > + wlan-en { > + pins = "gpio20"; > + function = "gpio"; > + > + drive-strength = <16>; > + output-high; > + bias-pull-up; > + }; > + }; > }; > > &uart12 { > -- > 2.29.2 >
On Fri, Jan 29, 2021 at 09:47:37PM -0600, Bjorn Andersson wrote: > On Thu 28 Jan 11:52 CST 2021, Dmitry Baryshkov wrote: > > > Add qca6391 to device tree as a way to provide power domain to WiFi and > > BT parts of the chip. > > > > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > --- > > arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 61 ++++++++++++++++++++++++ > > 1 file changed, 61 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > index 8aebc3660b11..2b0c1cc9333b 100644 > > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts > > @@ -151,6 +151,23 @@ vreg_s4a_1p8: vreg-s4a-1p8 { > > regulator-max-microvolt = <1800000>; > > regulator-always-on; > > }; > > + > > + qca6391: qca6391 { > > + compatible = "qcom,qca6390"; > > + #power-domain-cells = <0>; > > + > > + vddaon-supply = <&vreg_s6a_0p95>; > > + vddpmu-supply = <&vreg_s2f_0p95>; > > + vddrfa1-supply = <&vreg_s2f_0p95>; > > + vddrfa2-supply = <&vreg_s8c_1p3>; > > + vddrfa3-supply = <&vreg_s5a_1p9>; > > + vddpcie1-supply = <&vreg_s8c_1p3>; > > + vddpcie2-supply = <&vreg_s5a_1p9>; > > + vddio-supply = <&vreg_s4a_1p8>; > > + pinctrl-names = "default", "active"; > > + pinctrl-0 = <&wlan_default_state &bt_default_state>; > > + pinctrl-1 = <&wlan_active_state &bt_active_state>; > > I dislike the use of pinctrl states for toggling the level of the gpio > and would prefer that you use the gpio binding and api for this instead. > > > + }; > > }; > > > > &adsp { > > @@ -1013,6 +1030,28 @@ &tlmm { > > "HST_WLAN_UART_TX", > > "HST_WLAN_UART_RX"; > > > > + bt_default_state: bt-default-state { > > Are you sure you need to drive the BT_EN pin in order to have WiFi > working? On QCA6174 I believe the "WL_EN" was actually RESET_N and BT_EN > was actually "blueooth enable" - so we wired that in the bluetooth node > instead. > IIRC, that's the case. We need both BT_EN and WL_EN for proper bringup of the chip. Thanks, Mani
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 8aebc3660b11..2b0c1cc9333b 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -151,6 +151,23 @@ vreg_s4a_1p8: vreg-s4a-1p8 { regulator-max-microvolt = <1800000>; regulator-always-on; }; + + qca6391: qca6391 { + compatible = "qcom,qca6390"; + #power-domain-cells = <0>; + + vddaon-supply = <&vreg_s6a_0p95>; + vddpmu-supply = <&vreg_s2f_0p95>; + vddrfa1-supply = <&vreg_s2f_0p95>; + vddrfa2-supply = <&vreg_s8c_1p3>; + vddrfa3-supply = <&vreg_s5a_1p9>; + vddpcie1-supply = <&vreg_s8c_1p3>; + vddpcie2-supply = <&vreg_s5a_1p9>; + vddio-supply = <&vreg_s4a_1p8>; + pinctrl-names = "default", "active"; + pinctrl-0 = <&wlan_default_state &bt_default_state>; + pinctrl-1 = <&wlan_active_state &bt_active_state>; + }; }; &adsp { @@ -1013,6 +1030,28 @@ &tlmm { "HST_WLAN_UART_TX", "HST_WLAN_UART_RX"; + bt_default_state: bt-default-state { + bt-en { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <16>; + output-low; + bias-pull-up; + }; + }; + + bt_active_state: bt-active-state { + bt-en { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <16>; + output-high; + bias-pull-up; + }; + }; + lt9611_irq_pin: lt9611-irq { pins = "gpio63"; function = "gpio"; @@ -1119,6 +1158,28 @@ sdc2_card_det_n: sd-card-det-n { function = "gpio"; bias-pull-up; }; + + wlan_default_state: wlan-default-state { + wlan-en { + pins = "gpio20"; + function = "gpio"; + + drive-strength = <16>; + output-low; + bias-pull-up; + }; + }; + + wlan_active_state: wlan-active-state { + wlan-en { + pins = "gpio20"; + function = "gpio"; + + drive-strength = <16>; + output-high; + bias-pull-up; + }; + }; }; &uart12 {
Add qca6391 to device tree as a way to provide power domain to WiFi and BT parts of the chip. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 61 ++++++++++++++++++++++++ 1 file changed, 61 insertions(+) -- 2.29.2