diff mbox series

[v6,6/9] ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6

Message ID 1616757302-7889-5-git-send-email-dillon.minfei@gmail.com
State Superseded
Headers show
Series None | expand

Commit Message

Dillon Min March 26, 2021, 11:14 a.m. UTC
From: dillon min <dillon.minfei@gmail.com>

This patchset has following changes:

- introduce stm32h750.dtsi to support stm32h750 value line
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add dts binding usart3 for bt, uart4 for console
  usart3/uart4 pinctrl in stm32h7-pinctrl.dtsi
  usart3/uart4 register in stm32h743.dtsi
- add dts binding sdmmc2 for wifi
  sdmmc2 pinctrl in stm32h7-pinctrl.dtsi
  sdmmc2 register in stm32h743.dtsi
- add spi1 pinctrl in stm32h7-pinctrl.dtsi for spi flash
- add stm32h750-art-pi.dts to support art-pi board
- add pinctrl: pin-controller@58020000 {} to fix dtbs_check warrnings

art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm

the detail board information can be found at:
https://art-pi.gitee.io/website/

Signed-off-by: dillon min <dillon.minfei@gmail.com>
---

v6: no changes

 arch/arm/boot/dts/Makefile              |   1 +
 arch/arm/boot/dts/stm32h743.dtsi        | 164 ++++++++++++++++++++++-
 arch/arm/boot/dts/stm32h750.dtsi        |   6 +
 arch/arm/boot/dts/stm32h750i-art-pi.dts | 229 ++++++++++++++++++++++++++++++++
 4 files changed, 398 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/stm32h750.dtsi
 create mode 100644 arch/arm/boot/dts/stm32h750i-art-pi.dts
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 8e5d4ab4e75e..a19c5ab9df84 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1071,6 +1071,7 @@  dtb-$(CONFIG_ARCH_STM32) += \
 	stm32746g-eval.dtb \
 	stm32h743i-eval.dtb \
 	stm32h743i-disco.dtb \
+	stm32h750i-art-pi.dtb \
 	stm32mp153c-dhcom-drc02.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 4ebffb0a45a3..a17e98648e2a 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -135,6 +135,22 @@ 
 			clocks = <&rcc USART2_CK>;
 		};
 
+		usart3: serial@40004800 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004800 0x400>;
+			interrupts = <39>;
+			status = "disabled";
+			clocks = <&rcc USART3_CK>;
+		};
+
+		uart4: serial@40004c00 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004c00 0x400>;
+			interrupts = <52>;
+			status = "disabled";
+			clocks = <&rcc UART4_CK>;
+		};
+
 		i2c1: i2c@40005400 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
@@ -159,7 +175,7 @@ 
 			status = "disabled";
 		};
 
-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -368,6 +384,20 @@ 
 			max-frequency = <120000000>;
 		};
 
+		sdmmc2: mmc@48022400 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x10153180>;
+			reg = <0x48022400 0x400>;
+			interrupts = <124>;
+			interrupt-names	= "cmd_irq";
+			clocks = <&rcc SDMMC2_CK>;
+			clock-names = "apb_pclk";
+			resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+		};
+
 		exti: interrupt-controller@58000000 {
 			compatible = "st,stm32h7-exti";
 			interrupt-controller;
@@ -392,7 +422,7 @@ 
 			status = "disabled";
 		};
 
-		i2c4: i2c@58001C00 {
+		i2c4: i2c@58001c00 {
 			compatible = "st,stm32f7-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -555,6 +585,136 @@ 
 			snps,pbl = <8>;
 			status = "disabled";
 		};
+
+		pinctrl: pin-controller@58020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x58020000 0x3000>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&syscfg 0x8>;
+			pins-are-numbered;
+
+			gpioa: gpio@58020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA_CK>;
+				st,bank-name = "GPIOA";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpiob: gpio@58020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x400 0x400>;
+				clocks = <&rcc GPIOB_CK>;
+				st,bank-name = "GPIOB";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpioc: gpio@58020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x800 0x400>;
+				clocks = <&rcc GPIOC_CK>;
+				st,bank-name = "GPIOC";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpiod: gpio@58020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0xc00 0x400>;
+				clocks = <&rcc GPIOD_CK>;
+				st,bank-name = "GPIOD";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpioe: gpio@58021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOE_CK>;
+				st,bank-name = "GPIOE";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpiof: gpio@58021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1400 0x400>;
+				clocks = <&rcc GPIOF_CK>;
+				st,bank-name = "GPIOF";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpiog: gpio@58021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1800 0x400>;
+				clocks = <&rcc GPIOG_CK>;
+				st,bank-name = "GPIOG";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpioh: gpio@58021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc GPIOH_CK>;
+				st,bank-name = "GPIOH";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpioi: gpio@58022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOI_CK>;
+				st,bank-name = "GPIOI";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpioj: gpio@58022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2400 0x400>;
+				clocks = <&rcc GPIOJ_CK>;
+				st,bank-name = "GPIOJ";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpiok: gpio@58022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2800 0x400>;
+				clocks = <&rcc GPIOK_CK>;
+				st,bank-name = "GPIOK";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi
new file mode 100644
index 000000000000..41e3b1e3a874
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750.dtsi
@@ -0,0 +1,6 @@ 
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
+
+#include "stm32h743.dtsi"
+
+
diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
new file mode 100644
index 000000000000..098181efd172
--- /dev/null
+++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
@@ -0,0 +1,229 @@ 
+/*
+ * Copyright 2021 - Dillon Min <dillon.minfei@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * For art-pi board resources, you can refer to link:
+ * 	https://art-pi.gitee.io/website/
+ */
+
+/dts-v1/;
+#include "stm32h750.dtsi"
+#include "stm32h750-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "RT-Thread STM32H750i-ART-PI board";
+	compatible = "st,stm32h750i-art-pi", "st,stm32h750";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:2000000n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x2000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			no-map;
+			size = <0x100000>;
+			linux,dma-default;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			gpios = <&gpioi 8 0>;
+		};
+		led-green {
+			gpios = <&gpioc 15 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&mac {
+	status = "disabled";
+	pinctrl-0	= <&ethernet_rmii>;
+	pinctrl-names	= "default";
+	phy-mode	= "rmii";
+	phy-handle	= <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
+	dmas = <&dmamux1 37 0x400 0x05>,
+	       <&dmamux1 38 0x400 0x05>;
+	dma-names = "rx", "tx";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+
+		partition@0 {
+			label = "root filesystem";
+			reg = <0 0x1000000>;
+		};
+	};
+};
+
+&usart2 {
+	pinctrl-0 = <&usart2_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins>;
+	dmas = <&dmamux1 45 0x400 0x05>,
+	       <&dmamux1 46 0x400 0x05>;
+	dma-names = "rx", "tx";
+	st,hw-flow-ctrl;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+		max-speed = <115200>;
+	};
+};
+
+&uart4 {
+	pinctrl-0 = <&uart4_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+