diff mbox

[v2,3/8] mmc: sdhci-st: Add delay management functions for top registers (eMMC).

Message ID 1424956227-18258-4-git-send-email-peter.griffin@linaro.org
State New
Headers show

Commit Message

Peter Griffin Feb. 26, 2015, 1:10 p.m. UTC
Due to the tight timing constriants in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -

1) Static delay management
2) Dynamic delay management

NB: The delay management is only there when eMMC interface is selected.

1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.

2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.

The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
---
 drivers/mmc/host/sdhci-st.c | 58 +++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

Comments

Peter Griffin March 30, 2015, 10:33 a.m. UTC | #1
Hi Maxime,

On Tue, 03 Mar 2015, Maxime Coquelin wrote:
> 
> On 02/26/2015 02:10 PM, Peter Griffin wrote:
> >Due to the tight timing constriants in some UHS modes, it is required to have
> s/constriant/constraints/

Will fix.

<snip>
> >+
> >+static inline void st_mmcss_set_static_delay(void __iomem *ioaddr)
> >+{
> >+	if (ioaddr) {
> Maybe you could do:
>     if (!ioaddr)
>         return;

Yes good idea, I have made that change in V3.
> 
>     writel_relaxed....
> >+		writel_relaxed(0x0, ioaddr + ST_TOP_MMC_DLY_CTRL);
> >+		writel_relaxed(ST_TOP_MMC_DLY_MAX,
> >+				ioaddr + ST_TOP_MMC_TX_CLK_DLY);
> >+	}
> >+}
> >+
> >+static inline void st_mmcss_set_dll(void __iomem *ioaddr)
> >+{
> >+	if (ioaddr) {
> Ditto

regards,

Peter
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/mmc/host/sdhci-st.c b/drivers/mmc/host/sdhci-st.c
index 0101ae9..3443cc0 100644
--- a/drivers/mmc/host/sdhci-st.c
+++ b/drivers/mmc/host/sdhci-st.c
@@ -122,6 +122,64 @@  struct st_mmc_platform_data {
 		 ST_TOP_MMC_DLY_CTRL_ATUNE_NOT_CFG_DLY | \
 		 ST_TOP_MMC_START_DLL_LOCK)
 
+/*
+ * For clock speeds greater than 90MHz, we need to check that the
+ * DLL procedure has finished before switching to ultra-speed modes.
+ */
+#define	CLK_TO_CHECK_DLL_LOCK	90000000
+
+static inline void st_mmcss_set_static_delay(void __iomem *ioaddr)
+{
+	if (ioaddr) {
+		writel_relaxed(0x0, ioaddr + ST_TOP_MMC_DLY_CTRL);
+		writel_relaxed(ST_TOP_MMC_DLY_MAX,
+				ioaddr + ST_TOP_MMC_TX_CLK_DLY);
+	}
+}
+
+static inline void st_mmcss_set_dll(void __iomem *ioaddr)
+{
+	if (ioaddr) {
+		writel_relaxed(ST_TOP_MMC_DYN_DLY_CONF,
+			ioaddr + ST_TOP_MMC_DLY_CTRL);
+		writel_relaxed(ST_TOP_MMC_TX_DLL_STEP_DLY_VALID,
+			ioaddr + ST_TOP_MMC_TX_DLL_STEP_DLY);
+	}
+}
+
+static int st_mmcss_lock_dll(void __iomem *ioaddr)
+{
+	unsigned long curr, value;
+	unsigned long finish = jiffies + HZ;
+
+	/* Checks if the DLL procedure is finished */
+	do {
+		curr = jiffies;
+		value = readl(ioaddr + ST_MMC_STATUS_R);
+		if (value & 0x1)
+			return 0;
+
+		cpu_relax();
+	} while (!time_after_eq(curr, finish));
+
+	return -EBUSY;
+}
+
+static int sdhci_st_set_dll_for_clock(struct sdhci_host *host)
+{
+	int ret = 0;
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct st_mmc_platform_data *pdata = pltfm_host->priv;
+
+	if (host->clock > CLK_TO_CHECK_DLL_LOCK) {
+		st_mmcss_set_dll(pdata->top_ioaddr);
+		ret = st_mmcss_lock_dll(host->ioaddr);
+	}
+
+	return ret;
+}
+
+
 static u32 sdhci_st_readl(struct sdhci_host *host, int reg)
 {
 	u32 ret;