diff mbox series

[1/3] dt-bindings: pci: Add devicetree binding for Qualcomm PCIe EP controller

Message ID 20210602120752.46154-2-manivannan.sadhasivam@linaro.org
State New
Headers show
Series Add Qualcomm PCIe Endpoint driver support | expand

Commit Message

Manivannan Sadhasivam June 2, 2021, 12:07 p.m. UTC
Add devicetree binding for Qualcomm PCIe EP controller used in platforms
like SDX55. The EP controller is based on the Designware core with
Qualcomm specific wrappers.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

---
 .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++
 1 file changed, 139 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml

-- 
2.25.1

Comments

Rob Herring June 2, 2021, 2:22 p.m. UTC | #1
On Wed, Jun 2, 2021 at 7:08 AM Manivannan Sadhasivam
<manivannan.sadhasivam@linaro.org> wrote:
>
> Add devicetree binding for Qualcomm PCIe EP controller used in platforms
> like SDX55. The EP controller is based on the Designware core with
> Qualcomm specific wrappers.

Is the block EP only or configurable EP or host?

>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>  .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++
>  1 file changed, 139 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
>
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> new file mode 100644
> index 000000000000..0f9140e93bcb
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> @@ -0,0 +1,139 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm PCIe Endpoint Controller binding
> +
> +maintainers:
> +  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> +
> +allOf:
> +  - $ref: "pci-ep.yaml#"
> +
> +properties:
> +  compatible:
> +    const: qcom,pcie-ep

SoC specific please.

> +
> +  reg:
> +    items:
> +      - description: Designware PCIe registers
> +      - description: External local bus interface registers
> +      - description: Address Translation Unit (ATU) registers
> +      - description: Memory region used to map remote RC address space
> +      - description: Qualcomm specific PARF configuration registers
> +      - description: Qualcomm specific TCSR registers
> +
> +  reg-names:
> +    items:
> +      - const: dbi
> +      - const: elbi
> +      - const: atu
> +      - const: addr_space
> +      - const: parf
> +      - const: tcsr

This should be in the same order as the host side. Unfortunately,
that's not consistent, but to pick one:

reg-names = "parf", "dbi", "elbi", "atu", "config";


> +
> +  clocks:
> +    items:
> +      - description: PCIe CFG AHB clock
> +      - description: PCIe Auxiliary clock
> +      - description: PCIe Master AXI clock
> +      - description: PCIe Slave AXI clock
> +      - description: PCIe Reference clock
> +      - description: PCIe Sleep clock
> +      - description: PCIe Slave Q2A AXI clock
> +
> +  clock-names:
> +    items:
> +      - const: cfg
> +      - const: aux
> +      - const: bus_master
> +      - const: bus_slave
> +      - const: ref
> +      - const: sleep
> +      - const: slave_q2a

Again, try to keep the same ordering.

I have to wonder where 'pipe' clock is that most of the QCom
implementations have?

> +
> +  interrupts:
> +    maxItems: 1
> +    description: PCIe Global interrupt
> +
> +  interrupt-names:
> +    const: int_global

'int_' is redundant, drop.

> +
> +  perst-gpios:
> +    description: PCIe endpoint reset GPIO

An input, right?

> +    maxItems: 1
> +
> +  wake-gpios:
> +    description: PCIe endpoint wake GPIO
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  reset-names:
> +    const: core_reset

Not yet another name. We already have 'pci' and 'core' in the cases of
a single reset.

> +
> +  power-domains:
> +    maxItems: 1
> +
> +  phys:
> +    maxItems: 1
> +
> +  phy-names:
> +    const: pciephy
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - clocks
> +  - clock-names
> +  - interrupts
> +  - interrupt-names
> +  - perst-gpios
> +  - resets
> +  - reset-names
> +  - power-domains
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,gcc-sdx55.h>
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    pcie_ep: pcie-ep@40000000 {
> +        compatible = "qcom,pcie-ep";
> +
> +        reg = <0x40000000 0xf1d>,
> +              <0x40000f20 0xc8>,
> +              <0x40001000 0x1000>,
> +              <0x42000000 0x1000>,
> +              <0x01c00000 0x3000>,
> +              <0x01fcb000 0x1000>;
> +        reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr";
> +
> +        clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>,
> +             <&gcc GCC_PCIE_AUX_CLK>,
> +             <&gcc GCC_PCIE_MSTR_AXI_CLK>,
> +             <&gcc GCC_PCIE_SLV_AXI_CLK>,
> +             <&gcc GCC_PCIE_0_CLKREF_CLK>,
> +             <&gcc GCC_PCIE_SLEEP_CLK>,
> +             <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>;
> +        clock-names = "cfg", "aux", "bus_master", "bus_slave",
> +                      "ref", "sleep", "slave_q2a";
> +
> +        interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> +        interrupt-names = "int_global";
> +        perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
> +        wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
> +        resets = <&gcc GCC_PCIE_BCR>;
> +        reset-names = "core_reset";
> +        power-domains = <&gcc PCIE_GDSC>;
> +        phys = <&pcie0_lane>;
> +        phy-names = "pciephy";
> +        max-link-speed = <3>;
> +        num-lanes = <2>;

Should be documented. I'd assume the max is less than 16 which is
presumably what pcie-ep.yaml allows.

> +    };
> --
> 2.25.1
>
Manivannan Sadhasivam June 2, 2021, 2:37 p.m. UTC | #2
On Wed, Jun 02, 2021 at 09:22:29AM -0500, Rob Herring wrote:
> On Wed, Jun 2, 2021 at 7:08 AM Manivannan Sadhasivam
> <manivannan.sadhasivam@linaro.org> wrote:
> >
> > Add devicetree binding for Qualcomm PCIe EP controller used in platforms
> > like SDX55. The EP controller is based on the Designware core with
> > Qualcomm specific wrappers.
> 
> Is the block EP only or configurable EP or host?
> 

Configurable core. We already support the RC mode in a separate driver and
binding. I initially thought about merging both in a single driver &
binding but that seemed unnecessarily complex, so settled with this.

> >
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> >  .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 139 ++++++++++++++++++
> >  1 file changed, 139 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> > new file mode 100644
> > index 000000000000..0f9140e93bcb
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
> > @@ -0,0 +1,139 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Qualcomm PCIe Endpoint Controller binding
> > +
> > +maintainers:
> > +  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > +
> > +allOf:
> > +  - $ref: "pci-ep.yaml#"
> > +
> > +properties:
> > +  compatible:
> > +    const: qcom,pcie-ep
> 
> SoC specific please.
>

Okay

> > +
> > +  reg:
> > +    items:
> > +      - description: Designware PCIe registers
> > +      - description: External local bus interface registers
> > +      - description: Address Translation Unit (ATU) registers
> > +      - description: Memory region used to map remote RC address space
> > +      - description: Qualcomm specific PARF configuration registers
> > +      - description: Qualcomm specific TCSR registers
> > +
> > +  reg-names:
> > +    items:
> > +      - const: dbi
> > +      - const: elbi
> > +      - const: atu
> > +      - const: addr_space
> > +      - const: parf
> > +      - const: tcsr
> 
> This should be in the same order as the host side. Unfortunately,
> that's not consistent, but to pick one:
> 
> reg-names = "parf", "dbi", "elbi", "atu", "config";
> 

Okay, I'll align with the RC binding.

> 
> > +
> > +  clocks:
> > +    items:
> > +      - description: PCIe CFG AHB clock
> > +      - description: PCIe Auxiliary clock
> > +      - description: PCIe Master AXI clock
> > +      - description: PCIe Slave AXI clock
> > +      - description: PCIe Reference clock
> > +      - description: PCIe Sleep clock
> > +      - description: PCIe Slave Q2A AXI clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: cfg
> > +      - const: aux
> > +      - const: bus_master
> > +      - const: bus_slave
> > +      - const: ref
> > +      - const: sleep
> > +      - const: slave_q2a
> 
> Again, try to keep the same ordering.
> 
> I have to wonder where 'pipe' clock is that most of the QCom
> implementations have?
> 

Pipe clock is managed by the PHY driver. So the PCIe drivers need not to
worry about it.

> > +
> > +  interrupts:
> > +    maxItems: 1
> > +    description: PCIe Global interrupt
> > +
> > +  interrupt-names:
> > +    const: int_global
> 
> 'int_' is redundant, drop.
> 

Okay

> > +
> > +  perst-gpios:
> > +    description: PCIe endpoint reset GPIO
> 
> An input, right?
> 

Yes, will mention.

> > +    maxItems: 1
> > +
> > +  wake-gpios:
> > +    description: PCIe endpoint wake GPIO
> > +    maxItems: 1
> > +
> > +  resets:
> > +    maxItems: 1
> > +
> > +  reset-names:
> > +    const: core_reset
> 
> Not yet another name. We already have 'pci' and 'core' in the cases of
> a single reset.
> 

Okay

> > +
> > +  power-domains:
> > +    maxItems: 1
> > +
> > +  phys:
> > +    maxItems: 1
> > +
> > +  phy-names:
> > +    const: pciephy
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - reg-names
> > +  - clocks
> > +  - clock-names
> > +  - interrupts
> > +  - interrupt-names
> > +  - perst-gpios
> > +  - resets
> > +  - reset-names
> > +  - power-domains
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/clock/qcom,gcc-sdx55.h>
> > +    #include <dt-bindings/gpio/gpio.h>
> > +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> > +    pcie_ep: pcie-ep@40000000 {
> > +        compatible = "qcom,pcie-ep";
> > +
> > +        reg = <0x40000000 0xf1d>,
> > +              <0x40000f20 0xc8>,
> > +              <0x40001000 0x1000>,
> > +              <0x42000000 0x1000>,
> > +              <0x01c00000 0x3000>,
> > +              <0x01fcb000 0x1000>;
> > +        reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr";
> > +
> > +        clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>,
> > +             <&gcc GCC_PCIE_AUX_CLK>,
> > +             <&gcc GCC_PCIE_MSTR_AXI_CLK>,
> > +             <&gcc GCC_PCIE_SLV_AXI_CLK>,
> > +             <&gcc GCC_PCIE_0_CLKREF_CLK>,
> > +             <&gcc GCC_PCIE_SLEEP_CLK>,
> > +             <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>;
> > +        clock-names = "cfg", "aux", "bus_master", "bus_slave",
> > +                      "ref", "sleep", "slave_q2a";
> > +
> > +        interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> > +        interrupt-names = "int_global";
> > +        perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
> > +        wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
> > +        resets = <&gcc GCC_PCIE_BCR>;
> > +        reset-names = "core_reset";
> > +        power-domains = <&gcc PCIE_GDSC>;
> > +        phys = <&pcie0_lane>;
> > +        phy-names = "pciephy";
> > +        max-link-speed = <3>;
> > +        num-lanes = <2>;
> 
> Should be documented. I'd assume the max is less than 16 which is
> presumably what pcie-ep.yaml allows.
> 

okay

Thanks,
Mani

> > +    };
> > --
> > 2.25.1
> >
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
new file mode 100644
index 000000000000..0f9140e93bcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
@@ -0,0 +1,139 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/qcom,pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PCIe Endpoint Controller binding
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+allOf:
+  - $ref: "pci-ep.yaml#"
+
+properties:
+  compatible:
+    const: qcom,pcie-ep
+
+  reg:
+    items:
+      - description: Designware PCIe registers
+      - description: External local bus interface registers
+      - description: Address Translation Unit (ATU) registers
+      - description: Memory region used to map remote RC address space
+      - description: Qualcomm specific PARF configuration registers
+      - description: Qualcomm specific TCSR registers
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: elbi
+      - const: atu
+      - const: addr_space
+      - const: parf
+      - const: tcsr
+
+  clocks:
+    items:
+      - description: PCIe CFG AHB clock
+      - description: PCIe Auxiliary clock
+      - description: PCIe Master AXI clock
+      - description: PCIe Slave AXI clock
+      - description: PCIe Reference clock
+      - description: PCIe Sleep clock
+      - description: PCIe Slave Q2A AXI clock
+
+  clock-names:
+    items:
+      - const: cfg
+      - const: aux
+      - const: bus_master
+      - const: bus_slave
+      - const: ref
+      - const: sleep
+      - const: slave_q2a
+
+  interrupts:
+    maxItems: 1
+    description: PCIe Global interrupt
+
+  interrupt-names:
+    const: int_global
+
+  perst-gpios:
+    description: PCIe endpoint reset GPIO
+    maxItems: 1
+
+  wake-gpios:
+    description: PCIe endpoint wake GPIO
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: core_reset
+
+  power-domains:
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: pciephy
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - interrupts
+  - interrupt-names
+  - perst-gpios
+  - resets
+  - reset-names
+  - power-domains
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sdx55.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    pcie_ep: pcie-ep@40000000 {
+        compatible = "qcom,pcie-ep";
+
+        reg = <0x40000000 0xf1d>,
+              <0x40000f20 0xc8>,
+              <0x40001000 0x1000>,
+              <0x42000000 0x1000>,
+              <0x01c00000 0x3000>,
+              <0x01fcb000 0x1000>;
+        reg-names = "dbi", "elbi", "atu", "addr_space", "parf", "tcsr";
+
+        clocks = <&gcc GCC_PCIE_CFG_AHB_CLK>,
+             <&gcc GCC_PCIE_AUX_CLK>,
+             <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+             <&gcc GCC_PCIE_SLV_AXI_CLK>,
+             <&gcc GCC_PCIE_0_CLKREF_CLK>,
+             <&gcc GCC_PCIE_SLEEP_CLK>,
+             <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>;
+        clock-names = "cfg", "aux", "bus_master", "bus_slave",
+                      "ref", "sleep", "slave_q2a";
+
+        interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "int_global";
+        perst-gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
+        wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+        resets = <&gcc GCC_PCIE_BCR>;
+        reset-names = "core_reset";
+        power-domains = <&gcc PCIE_GDSC>;
+        phys = <&pcie0_lane>;
+        phy-names = "pciephy";
+        max-link-speed = <3>;
+        num-lanes = <2>;
+    };