diff mbox

net/fec: check id_entry pointer before using it

Message ID AANLkTin9uVOKY0dsJFQ1KNM2x9G1meoMCeQjec2XgmEK@mail.gmail.com
State New
Headers show

Commit Message

Jason Liu March 9, 2011, 4:47 a.m. UTC 
---------- Forwarded message ----------
From: Jason Liu <jason.hui@linaro.org>
Date: 2011/3/9
Subject: [PATCH] net/fec: check id_entry pointer before using it
To: linux-arm-kernel@lists.infradead.org
抄送： davem@davemloft.net


The id_entry will possibly be NULL, So, need check
id_entry and make sure it not NULL before using it.

Signed-off-by: Jason Liu <r64343@freescale.com>
---
 drivers/net/fec.c |   12 ++++++------
 1 files changed, 6 insertions(+), 6 deletions(-)

       /* Save skb pointer */
@@ -530,7 +530,7 @@ fec_enet_rx(struct net_device *dev)
               dma_unmap_single(NULL, bdp->cbd_bufaddr, bdp->cbd_datlen,
                               DMA_FROM_DEVICE);

-               if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
+               if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
                       swap_buffer(data, pkt_len);

               /* This does 16 byte alignment, exactly what we need.
@@ -809,7 +809,7 @@ static int fec_enet_mii_init(struct platform_device *pdev)
        * mdio interface in board design, and need to be configured by
        * fec0 mii_bus.
        */
-       if ((id_entry->driver_data & FEC_QUIRK_ENET_MAC) && pdev->id) {
+       if (id_entry && (id_entry->driver_data & FEC_QUIRK_ENET_MAC)
&& pdev->id) {
               /* fec1 uses fec0 mii_bus */
               fep->mii_bus = fec0_mii_bus;
               return 0;
@@ -852,7 +852,7 @@ static int fec_enet_mii_init(struct platform_device *pdev)
               goto err_out_free_mdio_irq;

       /* save fec0 mii_bus */
-       if (id_entry->driver_data & FEC_QUIRK_ENET_MAC)
+       if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC)
               fec0_mii_bus = fep->mii_bus;

       return 0;
@@ -1239,7 +1239,7 @@ fec_restart(struct net_device *dev, int duplex)
        * enet-mac reset will reset mac address registers too,
        * so need to reconfigure it.
        */
-       if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
+       if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
               memcpy(&temp_mac, dev->dev_addr, ETH_ALEN);
               writel(cpu_to_be32(temp_mac[0]), fep->hwp + FEC_ADDR_LOW);
               writel(cpu_to_be32(temp_mac[1]), fep->hwp + FEC_ADDR_HIGH);
@@ -1295,7 +1295,7 @@ fec_restart(struct net_device *dev, int duplex)
        * The phy interface and speed need to get configured
        * differently on enet-mac.
        */
-       if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
+       if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
               val = readl(fep->hwp + FEC_R_CNTRL);

               /* MII or RMII */
--
1.7.1
diff mbox

Patch

diff --git a/drivers/net/fec.c b/drivers/net/fec.c
index cd0282d..e97ee0f 100644
--- a/drivers/net/fec.c
+++ b/drivers/net/fec.c
@@ -294,7 +294,7 @@  fec_enet_start_xmit(struct sk_buff *skb, struct
net_device *dev)
        * the system that it's running on. As the result, driver has to
        * swap every frame going to and coming from the controller.
        */
-       if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
+       if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
               swap_buffer(bufaddr, skb->len);