| Message ID | 1427176113-23411-1-git-send-email-zhang.chunyan@linaro.org |
|---|---|
| State | New |
| Headers | show |
On 23 March 2015 at 23:48, Chunyan Zhang <zhang.chunyan@linaro.org> wrote: > Support only for ETB, FUNNEL, STM are included currently. > Support for ETM, TPIU and the replicator linked to it are not included in > this version patch. > > Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> > --- > arch/arm64/boot/dts/sprd/sc9836.dtsi | 57 ++++++++++++++++++++++++++++++++++++ > 1 file changed, 57 insertions(+) > > diff --git a/arch/arm64/boot/dts/sprd/sc9836.dtsi b/arch/arm64/boot/dts/sprd/sc9836.dtsi > index f92f1b4..2ca80f3 100644 > --- a/arch/arm64/boot/dts/sprd/sc9836.dtsi > +++ b/arch/arm64/boot/dts/sprd/sc9836.dtsi > @@ -45,6 +45,63 @@ > }; > }; > > + etb@10003000 { > + compatible = "arm,coresight-etb10", "arm,primecell"; > + reg = <0 0x10003000 0 0x1000>; > + arm,primecell-periphid = <0x0003b907>; Specifying the primecell id in the device tree like this is usually to avoid probing of the memory space by the AMBA mechanic when bus components are discovered. As such components are probed and initialised when their drivers are registered with the diver core later in the boot process. Is there a good reason why this is done here? Especially when the funnel and STM don't specify their cell IDs in the DT. > + coresight-default-sink; Please remove the above - this feature no longer exists. > + clocks = <&clk26mhz>; > + clock-names = "apb_pclk"; > + port { > + etb_in: endpoint { > + slave-mode; > + remote-endpoint = <&funnel_out_port0>; > + }; > + }; > + }; > + > + funnel@10001000 { > + compatible = "arm,coresight-funnel", "arm,primecell"; > + reg = <0 0x10001000 0 0x1000>; > + clocks = <&clk26mhz>; > + clock-names = "apb_pclk"; > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* funnel output port */ > + port@0 { > + reg = <0>; > + funnel_out_port0: endpoint { > + remote-endpoint = <&etb_in>; > + }; > + }; > + > + /* funnel input port 0~3 is reserved for ETMs */ > + port@1 { > + reg = <4>; > + funnel_in_port4: endpoint { > + slave-mode; > + remote-endpoint = <&stm_out>; > + }; > + }; > + }; > + }; > + > + stm@10006000 { > + compatible = "arm,coresight-stm", "arm,primecell"; > + reg = <0 0x10006000 0 0x1000>, > + <0 0x01000000 0 0x180000>; > + reg-names = "stm-base", "stm-stimulus-base"; > + clocks = <&clk26mhz>; > + clock-names = "apb_pclk"; > + port { > + stm_out: endpoint { > + remote-endpoint = <&funnel_in_port4>; > + }; > + }; > + }; > + > gic: interrupt-controller@12001000 { > compatible = "arm,gic-400"; > reg = <0 0x12001000 0 0x1000>, > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Mar 24, 2015 at 11:08 PM, Mathieu Poirier <mathieu.poirier@linaro.org> wrote: > On 23 March 2015 at 23:48, Chunyan Zhang <zhang.chunyan@linaro.org> wrote: >> Support only for ETB, FUNNEL, STM are included currently. >> Support for ETM, TPIU and the replicator linked to it are not included in >> this version patch. >> >> Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> >> --- >> arch/arm64/boot/dts/sprd/sc9836.dtsi | 57 ++++++++++++++++++++++++++++++++++++ >> 1 file changed, 57 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/sprd/sc9836.dtsi b/arch/arm64/boot/dts/sprd/sc9836.dtsi >> index f92f1b4..2ca80f3 100644 >> --- a/arch/arm64/boot/dts/sprd/sc9836.dtsi >> +++ b/arch/arm64/boot/dts/sprd/sc9836.dtsi >> @@ -45,6 +45,63 @@ >> }; >> }; >> >> + etb@10003000 { >> + compatible = "arm,coresight-etb10", "arm,primecell"; >> + reg = <0 0x10003000 0 0x1000>; >> + arm,primecell-periphid = <0x0003b907>; > > Specifying the primecell id in the device tree like this is usually to > avoid probing of the memory space by the AMBA mechanic when bus > components are discovered. As such components are probed and > initialised when their drivers are registered with the diver core > later in the boot process. > > Is there a good reason why this is done here? Especially when the > funnel and STM don't specify their cell IDs in the DT. Actually today I found that is not a ETB but TMC, so if I didn't set peripheral id for it in DT, it can't be initialized as ETB. I will correct it to be a TMC in upcoming version patch. > >> + coresight-default-sink; > > Please remove the above - this feature no longer exists. ok, I will remove it in next version. > >> + clocks = <&clk26mhz>; >> + clock-names = "apb_pclk"; >> + port { >> + etb_in: endpoint { >> + slave-mode; >> + remote-endpoint = <&funnel_out_port0>; >> + }; >> + }; >> + }; >> + >> + funnel@10001000 { >> + compatible = "arm,coresight-funnel", "arm,primecell"; >> + reg = <0 0x10001000 0 0x1000>; >> + clocks = <&clk26mhz>; >> + clock-names = "apb_pclk"; >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + /* funnel output port */ >> + port@0 { >> + reg = <0>; >> + funnel_out_port0: endpoint { >> + remote-endpoint = <&etb_in>; >> + }; >> + }; >> + >> + /* funnel input port 0~3 is reserved for ETMs */ >> + port@1 { >> + reg = <4>; >> + funnel_in_port4: endpoint { >> + slave-mode; >> + remote-endpoint = <&stm_out>; >> + }; >> + }; >> + }; >> + }; >> + >> + stm@10006000 { >> + compatible = "arm,coresight-stm", "arm,primecell"; >> + reg = <0 0x10006000 0 0x1000>, >> + <0 0x01000000 0 0x180000>; >> + reg-names = "stm-base", "stm-stimulus-base"; >> + clocks = <&clk26mhz>; >> + clock-names = "apb_pclk"; >> + port { >> + stm_out: endpoint { >> + remote-endpoint = <&funnel_in_port4>; >> + }; >> + }; >> + }; >> + >> gic: interrupt-controller@12001000 { >> compatible = "arm,gic-400"; >> reg = <0 0x12001000 0 0x1000>, >> -- >> 1.9.1 >> -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm64/boot/dts/sprd/sc9836.dtsi b/arch/arm64/boot/dts/sprd/sc9836.dtsi index f92f1b4..2ca80f3 100644 --- a/arch/arm64/boot/dts/sprd/sc9836.dtsi +++ b/arch/arm64/boot/dts/sprd/sc9836.dtsi @@ -45,6 +45,63 @@ }; }; + etb@10003000 { + compatible = "arm,coresight-etb10", "arm,primecell"; + reg = <0 0x10003000 0 0x1000>; + arm,primecell-periphid = <0x0003b907>; + coresight-default-sink; + clocks = <&clk26mhz>; + clock-names = "apb_pclk"; + port { + etb_in: endpoint { + slave-mode; + remote-endpoint = <&funnel_out_port0>; + }; + }; + }; + + funnel@10001000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0 0x10001000 0 0x1000>; + clocks = <&clk26mhz>; + clock-names = "apb_pclk"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* funnel output port */ + port@0 { + reg = <0>; + funnel_out_port0: endpoint { + remote-endpoint = <&etb_in>; + }; + }; + + /* funnel input port 0~3 is reserved for ETMs */ + port@1 { + reg = <4>; + funnel_in_port4: endpoint { + slave-mode; + remote-endpoint = <&stm_out>; + }; + }; + }; + }; + + stm@10006000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x10006000 0 0x1000>, + <0 0x01000000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + clocks = <&clk26mhz>; + clock-names = "apb_pclk"; + port { + stm_out: endpoint { + remote-endpoint = <&funnel_in_port4>; + }; + }; + }; + gic: interrupt-controller@12001000 { compatible = "arm,gic-400"; reg = <0 0x12001000 0 0x1000>,
Support only for ETB, FUNNEL, STM are included currently. Support for ETM, TPIU and the replicator linked to it are not included in this version patch. Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> --- arch/arm64/boot/dts/sprd/sc9836.dtsi | 57 ++++++++++++++++++++++++++++++++++++ 1 file changed, 57 insertions(+)