@@ -138,6 +138,87 @@ static inline void st_mmcss_set_static_delay(void __iomem *ioaddr)
ioaddr + ST_TOP_MMC_TX_CLK_DLY);
}
+/**
+ * st_mmcss_cconfig: configure the Arasan HC inside the flashSS.
+ * @np: dt device node.
+ * @host: sdhci host
+ * Description: this function is to configure the Arasan host controller.
+ * On some ST SoCs, i.e. STiH407 family, the MMC devices inside a dedicated
+ * flashSS sub-system which needs to be configured to be compliant to eMMC 4.5
+ * or eMMC4.3. This has to be done before registering the sdhci host.
+ */
+static void st_mmcss_cconfig(struct device_node *np, struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct mmc_host *mhost = host->mmc;
+ u32 cconf2, cconf3, cconf4, cconf5;
+
+ if (!of_device_is_compatible(np, "st,sdhci-stih407"))
+ return;
+
+ cconf2 = ST_MMC_CCONFIG_2_DEFAULT;
+ cconf3 = ST_MMC_CCONFIG_3_DEFAULT;
+ cconf4 = ST_MMC_CCONFIG_4_DEFAULT;
+ cconf5 = ST_MMC_CCONFIG_5_DEFAULT;
+
+ writel_relaxed(ST_MMC_CCONFIG_1_DEFAULT,
+ host->ioaddr + ST_MMC_CCONFIG_REG_1);
+
+ /* Set clock frequency, default to 50MHz if max-frequency is not
+ * provided */
+
+ switch (mhost->f_max) {
+ case 200000000:
+ clk_set_rate(pltfm_host->clk, mhost->f_max);
+ cconf2 |= BASE_CLK_FREQ_200;
+ break;
+ case 100000000:
+ clk_set_rate(pltfm_host->clk, mhost->f_max);
+ cconf2 |= BASE_CLK_FREQ_100;
+ break;
+ default:
+ clk_set_rate(pltfm_host->clk, 50000000);
+ cconf2 |= BASE_CLK_FREQ_50;
+ }
+
+ writel_relaxed(cconf2, host->ioaddr + ST_MMC_CCONFIG_REG_2);
+
+ if (mhost->caps & MMC_CAP_NONREMOVABLE)
+ cconf3 |= ST_MMC_CCONFIG_EMMC_SLOT_TYPE;
+ else
+ /* CARD _D ET_CTRL */
+ writel_relaxed(ST_MMC_GP_OUTPUT_CD,
+ host->ioaddr + ST_MMC_GP_OUTPUT);
+
+ if (mhost->caps & MMC_CAP_UHS_SDR50) {
+ /* use 1.8V */
+ cconf3 |= ST_MMC_CCONFIG_1P8_VOLT;
+ cconf4 |= ST_MMC_CCONFIG_SDR50;
+ /* Use tuning */
+ cconf5 |= ST_MMC_CCONFIG_TUNING_FOR_SDR50;
+ /* Max timeout for retuning */
+ cconf5 |= RETUNING_TIMER_CNT_MAX;
+ }
+
+ if (mhost->caps & MMC_CAP_UHS_SDR104) {
+ /*
+ * SDR104 implies the HC can support HS200 mode, so
+ * it's mandatory to use 1.8V
+ */
+ cconf3 |= ST_MMC_CCONFIG_1P8_VOLT;
+ cconf4 |= ST_MMC_CCONFIG_SDR104;
+ /* Max timeout for retuning */
+ cconf5 |= RETUNING_TIMER_CNT_MAX;
+ }
+
+ if (mhost->caps & MMC_CAP_UHS_DDR50)
+ cconf4 |= ST_MMC_CCONFIG_DDR50;
+
+ writel_relaxed(cconf3, host->ioaddr + ST_MMC_CCONFIG_REG_3);
+ writel_relaxed(cconf4, host->ioaddr + ST_MMC_CCONFIG_REG_4);
+ writel_relaxed(cconf5, host->ioaddr + ST_MMC_CCONFIG_REG_5);
+}
+
static inline void st_mmcss_set_dll(void __iomem *ioaddr)
{
if (!ioaddr)
@@ -214,6 +295,7 @@ static const struct sdhci_pltfm_data sdhci_st_pdata = {
static int sdhci_st_probe(struct platform_device *pdev)
{
+ struct device_node *np = pdev->dev.of_node;
struct sdhci_host *host;
struct st_mmc_platform_data *pdata;
struct sdhci_pltfm_host *pltfm_host;
@@ -266,6 +348,9 @@ static int sdhci_st_probe(struct platform_device *pdev)
pltfm_host->priv = pdata;
pltfm_host->clk = clk;
+ /* Configure the Arasan HC inside the flashSS */
+ st_mmcss_cconfig(np, host);
+
ret = sdhci_add_host(host);
if (ret) {
dev_err(&pdev->dev, "Failed sdhci_add_host\n");
@@ -332,12 +417,15 @@ static int sdhci_st_resume(struct device *dev)
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct st_mmc_platform_data *pdata = pltfm_host->priv;
+ struct device_node *np = dev->of_node;
clk_prepare_enable(pltfm_host->clk);
if (pdata->rstc)
reset_control_deassert(pdata->rstc);
+ st_mmcss_cconfig(np, host);
+
return sdhci_resume_host(host);
}
#endif