[V1] arm64: dts: qcom: sc7180: Use maximum drive strength values for eMMC

The current drive strength values are not sufficient on non discrete
boards and this leads to CRC errors during switching to HS400 enhanced
strobe mode.

Hardware simulation results on non discrete boards shows up that use the
maximum drive strength values for data and command lines could helps
in avoiding these CRC errors.

So, update data and command line drive strength values to maximum.

Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

Hi,

On Mon, Aug 16, 2021 at 9:51 AM Shaik Sajida Bhanu
<sbhanu@codeaurora.org> wrote:
>
> The current drive strength values are not sufficient on non discrete
> boards and this leads to CRC errors during switching to HS400 enhanced
> strobe mode.
>
> Hardware simulation results on non discrete boards shows up that use the
> maximum drive strength values for data and command lines could helps
> in avoiding these CRC errors.
>
> So, update data and command line drive strength values to maximum.
>
> Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)

I found this CL because you created a bug for it (thanks!), but it
would have also been nice if you had CCed some folks from Google that
work on the trogdor project on your patch.


> diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> index 0f2b3c0..79d7aa6 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> @@ -1524,13 +1524,13 @@ ap_spi_fp: &spi10 {
>                 pinconf-cmd {
>                         pins = "sdc1_cmd";
>                         bias-pull-up;
> -                       drive-strength = <10>;
> +                       drive-strength = <16>;
>                 };
>
>                 pinconf-data {
>                         pins = "sdc1_data";
>                         bias-pull-up;
> -                       drive-strength = <10>;
> +                       drive-strength = <16>;

I could be convinced that this is the right thing to do, but I want to
really make sure that it has had sufficient testing. Specifically as
this patch is written we'll be updating the drive strength for all
boards. Increasing the drive strength can sometimes introduce new
problems (reflections, noise, ...) so we have to be confident that
we're not breaking someone that used to work by increasing the drive
strength here. How much has this been tested?

Hi,

On Tue, Aug 17, 2021 at 6:58 AM Doug Anderson <dianders@google.com> wrote:
>
> >                 pinconf-data {
> >                         pins = "sdc1_data";
> >                         bias-pull-up;
> > -                       drive-strength = <10>;
> > +                       drive-strength = <16>;
>
> I could be convinced that this is the right thing to do, but I want to
> really make sure that it has had sufficient testing. Specifically as
> this patch is written we'll be updating the drive strength for all
> boards. Increasing the drive strength can sometimes introduce new
> problems (reflections, noise, ...) so we have to be confident that
> we're not breaking someone that used to work by increasing the drive
> strength here. How much has this been tested?