| Message ID | 1629282424-4070-3-git-send-email-mkrishn@codeaurora.org |
|---|---|
| State | New |
| Headers | show |
| Series | [v1,1/4] dt-bindings: msm: add DT bindings for sc7280 | expand |
On Wed, Aug 18, 2021 at 03:57:03PM +0530, Krishna Manikandan wrote: > From: Rajeev Nandan <rajeevny@codeaurora.org> > > Add DSI controller and PHY nodes for sc7280. > > Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org> You should sign off patches you send, even if you aren't the original author. > --- > arch/arm64/boot/dts/qcom/sc7280.dtsi | 101 +++++++++++++++++++++++++++++++++++ > 1 file changed, 101 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index fd7ff1c..aadf55d 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -1483,6 +1483,18 @@ > > status = "disabled"; > > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + }; > + > mdp_opp_table: mdp-opp-table { > compatible = "operating-points-v2"; > > @@ -1507,6 +1519,95 @@ > }; > }; > }; > + > + dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SC7280_CX>; > + > + phys = <&dsi_phy>; > + phy-names = "dsi"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + > + dsi_opp_table: dsi-opp-table { > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + > + dsi_phy: dsi-phy@ae94400 { > + compatible = "qcom,sc7280-dsi-phy-7nm"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x280>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + }; I'm not an expect, but this looks sane to me and it's very similar to the SC7180 config. Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index fd7ff1c..aadf55d 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -1483,6 +1483,18 @@ status = "disabled"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + mdp_opp_table: mdp-opp-table { compatible = "operating-points-v2"; @@ -1507,6 +1519,95 @@ }; }; }; + + dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SC7280_CX>; + + phys = <&dsi_phy>; + phy-names = "dsi"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + + dsi_phy: dsi-phy@ae94400 { + compatible = "qcom,sc7280-dsi-phy-7nm"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x280>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; }; pdc: interrupt-controller@b220000 {