diff mbox series

[v4,7/8] dt-bindings: memory-controllers: ti,gpmc: Convert to yaml

Message ID 20210914122705.15421-8-rogerq@kernel.org
State New
Headers show
Series dt-bindings: memory-controllers: ti,gpmc: Convert to yaml | expand

Commit Message

Roger Quadros Sept. 14, 2021, 12:27 p.m. UTC
Convert omap-gpmc.txt to ti,gpmc.yaml.

Signed-off-by: Roger Quadros <rogerq@kernel.org>
---
 .../bindings/memory-controllers/omap-gpmc.txt | 157 ----------------
 .../bindings/memory-controllers/ti,gpmc.yaml  | 172 ++++++++++++++++++
 2 files changed, 172 insertions(+), 157 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml

Comments

Krzysztof Kozlowski Sept. 15, 2021, 7:20 a.m. UTC | #1
On 14/09/2021 14:27, Roger Quadros wrote:
> Convert omap-gpmc.txt to ti,gpmc.yaml.
> 
> Signed-off-by: Roger Quadros <rogerq@kernel.org>
> ---
>  .../bindings/memory-controllers/omap-gpmc.txt | 157 ----------------
>  .../bindings/memory-controllers/ti,gpmc.yaml  | 172 ++++++++++++++++++
>  2 files changed, 172 insertions(+), 157 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
> 
> diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
> deleted file mode 100644
> index c1359f4d48d7..000000000000
> --- a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
> +++ /dev/null
> @@ -1,157 +0,0 @@
> -Device tree bindings for OMAP general purpose memory controllers (GPMC)
> -
> -The actual devices are instantiated from the child nodes of a GPMC node.
> -
> -Required properties:
> -
> - - compatible:		Should be set to one of the following:
> -
> -			ti,omap2420-gpmc (omap2420)
> -			ti,omap2430-gpmc (omap2430)
> -			ti,omap3430-gpmc (omap3430 & omap3630)
> -			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
> -			ti,am3352-gpmc   (am335x devices)
> -
> - - reg:			A resource specifier for the register space
> -			(see the example below)
> - - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
> -			completed.
> - - #address-cells:	Must be set to 2 to allow memory address translation
> - - #size-cells:		Must be set to 1 to allow CS address passing
> - - gpmc,num-cs:		The maximum number of chip-select lines that controller
> -			can support.
> - - gpmc,num-waitpins:	The maximum number of wait pins that controller can
> -			support.
> - - ranges:		Must be set up to reflect the memory layout with four
> -			integer values for each chip-select line in use:
> -
> -			   <cs-number> 0 <physical address of mapping> <size>
> -
> -			Currently, calculated values derived from the contents
> -			of the per-CS register GPMC_CONFIG7 (as set up by the
> -			bootloader) are used for the physical address decoding.
> -			As this will change in the future, filling correct
> -			values here is a requirement.
> - - interrupt-controller: The GPMC driver implements and interrupt controller for
> -			the NAND events "fifoevent" and "termcount" plus the
> -			rising/falling edges on the GPMC_WAIT pins.
> -			The interrupt number mapping is as follows
> -			0 - NAND_fifoevent
> -			1 - NAND_termcount
> -			2 - GPMC_WAIT0 pin edge
> -			3 - GPMC_WAIT1 pin edge, and so on.
> - - interrupt-cells:	Must be set to 2
> - - gpio-controller:	The GPMC driver implements a GPIO controller for the
> -			GPMC WAIT pins that can be used as general purpose inputs.
> -			0 maps to GPMC_WAIT0 pin.
> - - gpio-cells:		Must be set to 2
> -
> -Required properties when using NAND prefetch dma:
> - - dmas			GPMC NAND prefetch dma channel
> - - dma-names		Must be set to "rxtx"
> -
> -Timing properties for child nodes. All are optional and default to 0.
> -
> - - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
> -
> - Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
> - - gpmc,cs-on-ns:	Assertion time
> - - gpmc,cs-rd-off-ns:	Read deassertion time
> - - gpmc,cs-wr-off-ns:	Write deassertion time
> -
> - ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
> - - gpmc,adv-on-ns:	Assertion time
> - - gpmc,adv-rd-off-ns:	Read deassertion time
> - - gpmc,adv-wr-off-ns:	Write deassertion time
> - - gpmc,adv-aad-mux-on-ns:	Assertion time for AAD
> - - gpmc,adv-aad-mux-rd-off-ns:	Read deassertion time for AAD
> - - gpmc,adv-aad-mux-wr-off-ns:	Write deassertion time for AAD
> -
> - WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
> - - gpmc,we-on-ns	Assertion time
> - - gpmc,we-off-ns:	Deassertion time
> -
> - OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
> - - gpmc,oe-on-ns:	Assertion time
> - - gpmc,oe-off-ns:	Deassertion time
> - - gpmc,oe-aad-mux-on-ns:	Assertion time for AAD
> - - gpmc,oe-aad-mux-off-ns:	Deassertion time for AAD
> -
> - Access time and cycle time timings (in nanoseconds) corresponding to
> - GPMC_CONFIG5:
> - - gpmc,page-burst-access-ns: 	Multiple access word delay
> - - gpmc,access-ns:		Start-cycle to first data valid delay
> - - gpmc,rd-cycle-ns:		Total read cycle time
> - - gpmc,wr-cycle-ns:		Total write cycle time
> - - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
> - - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
> - - gpmc,clk-activation-ns: 	GPMC clock activation time
> - - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
> -				data
> -
> -Boolean timing parameters. If property is present parameter enabled and
> -disabled if omitted:
> - - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
> - - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
> - - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
> -				accesses to a different CS
> - - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
> -				accesses to the same CS
> - - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
> - - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
> - - gpmc,time-para-granularity:	Multiply all access times by 2
> -
> -The following are only applicable to OMAP3+ and AM335x:
> - - gpmc,wr-access-ns:		In synchronous write mode, for single or
> -				burst accesses, defines the number of
> -				GPMC_FCLK cycles from start access time
> -				to the GPMC_CLK rising edge used by the
> -				memory device for the first data capture.
> - - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
> -				the time when the first data is driven on
> -				the address-data bus.
> -
> -GPMC chip-select settings properties for child nodes. All are optional.
> -
> -- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
> -- gpmc,burst-wrap	Enables wrap bursting
> -- gpmc,burst-read	Enables read page/burst mode
> -- gpmc,burst-write	Enables write page/burst mode
> -- gpmc,device-width	Total width of device(s) connected to a GPMC
> -			chip-select in bytes. The GPMC supports 8-bit
> -			and 16-bit devices and so this property must be
> -			1 or 2.
> -- gpmc,mux-add-data	Address and data multiplexing configuration.
> -			Valid values are 1 for address-address-data
> -			multiplexing mode and 2 for address-data
> -			multiplexing mode.
> -- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
> -			is this is not set.
> -- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
> -			is this is not set.
> -- gpmc,wait-pin		Wait-pin used by client. Must be less than
> -			"gpmc,num-waitpins".
> -- gpmc,wait-on-read	Enables wait monitoring on reads.
> -- gpmc,wait-on-write	Enables wait monitoring on writes.
> -
> -Example for an AM33xx board:
> -
> -	gpmc: gpmc@50000000 {
> -		compatible = "ti,am3352-gpmc";
> -		ti,hwmods = "gpmc";
> -		reg = <0x50000000 0x2000>;
> -		interrupts = <100>;
> -		dmas = <&edma 52 0>;
> -		dma-names = "rxtx";
> -		gpmc,num-cs = <8>;
> -		gpmc,num-waitpins = <2>;
> -		#address-cells = <2>;
> -		#size-cells = <1>;
> -		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
> -		interrupt-controller;
> -		#interrupt-cells = <2>;
> -		gpio-controller;
> -		#gpio-cells = <2>;
> -
> -		/* child nodes go here */
> -	};
> diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
> new file mode 100644
> index 000000000000..d6cd39bd3940
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
> @@ -0,0 +1,172 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments GPMC Memory Controller device-tree bindings
> +
> +maintainers:
> +  - Tony Lindgren <tony@atomide.com>
> +  - Roger Quadros <rogerq@kernel.org>
> +
> +description:
> +  The GPMC is a unified memory controller dedicated for interfacing
> +  with external memory devices like
> +  - Asynchronous SRAM-like memories and ASICs
> +  - Asynchronous, synchronous, and page mode burst NOR flash
> +  - NAND flash
> +  - Pseudo-SRAM devices
> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +          - ti,omap2420-gpmc
> +          - ti,omap2430-gpmc
> +          - ti,omap3430-gpmc
> +          - ti,omap4430-gpmc
> +          - ti,am3352-gpmc

How about putting them in alphabetical order?

> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +    description: |
> +      Functional clock. Used for bus timing calculations and
> +      GPMC configuration.
> +
> +  clock-names:
> +    items:
> +      - const: fck
> +
> +  dmas:
> +    items:
> +      - description: DMA channel for GPMC NAND prefetch
> +
> +  dma-names:
> +    items:
> +      - const: rxtx
> +
> +  "#address-cells": true
> +
> +  "#size-cells": true
> +
> +  gpmc,num-cs:
> +    description: maximum number of supported chip-select lines.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  gpmc,num-waitpins:
> +    description: maximum number of supported wait pins.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  ranges:
> +    minItems: 1
> +    description: |
> +      Must be set up to reflect the memory layout with four
> +      integer values for each chip-select line in use,
> +      <cs-number> 0 <physical address of mapping> <size>
> +    items:
> +      - description: NAND bank 0
> +      - description: NOR/SRAM bank 0
> +      - description: NOR/SRAM bank 1
> +
> +  '#interrupt-cells':
> +    const: 2
> +
> +  interrupt-controller:
> +    description: |
> +      The GPMC driver implements and interrupt controller for
> +      the NAND events "fifoevent" and "termcount" plus the
> +      rising/falling edges on the GPMC_WAIT pins.
> +      The interrupt number mapping is as follows
> +      0 - NAND_fifoevent
> +      1 - NAND_termcount
> +      2 - GPMC_WAIT0 pin edge
> +      3 - GPMC_WAIT1 pin edge, and so on.
> +
> +  '#gpio-cells':
> +    const: 2
> +
> +  gpio-controller:
> +    description: |
> +      The GPMC driver implements a GPIO controller for the
> +      GPMC WAIT pins that can be used as general purpose inputs.
> +      0 maps to GPMC_WAIT0 pin.
> +
> +  ti,hwmods:
> +    description:
> +      Name of the HWMOD associated with GPMC. This is for legacy
> +      omap2/3 platforms only.
> +    $ref: /schemas/types.yaml#/definitions/string
> +    deprecated: true
> +
> +  ti,no-idle-on-init:
> +    description:
> +      Prevent idling the module at init. This is for legacy omap2/3
> +      platforms only.
> +    type: boolean
> +    deprecated: true
> +
> +patternProperties:
> +  "@[0-7],[a-f0-9]+$":
> +    type: object
> +    description: |
> +      The child device node represents the device connected to the GPMC
> +      bus. The device can be a NAND chip, SRAM device, NOR device
> +      or an ASIC.
> +
> +    allOf:
> +      - $ref: "ti,gpmc-child.yaml"
> +
> +    unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - gpmc,num-cs
> +  - gpmc,num-waitpins
> +  - "#address-cells"
> +  - "#size-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    gpmc: memory-controller@50000000 {
> +      compatible = "ti,am3352-gpmc";
> +      reg = <0x50000000 0x2000>;
> +      interrupts = <100>;
> +      clocks = <&l3s_clkctrl>;
> +      clock-names = "fck";
> +      dmas = <&edma 52 0>;
> +      dma-names = "rxtx";
> +      gpmc,num-cs = <8>;
> +      gpmc,num-waitpins = <2>;
> +      #address-cells = <2>;
> +      #size-cells = <1>;
> +      ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
> +      interrupt-controller;
> +      #interrupt-cells = <2>;
> +      gpio-controller;
> +      #gpio-cells = <2>;
> +
> +      nand@0,0 {
> +        compatible = "ti,omap2-nand";
> +        reg = <0 0 4>;
> +        interrupt-parent = <&gpmc>;
> +        interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
> +                     <1 IRQ_TYPE_NONE>; /* termcount */

Why these are interrupts of unspecified type (NONE)?

> +        ti,nand-xfer-type = "prefetch-dma";
> +        ti,nand-ecc-opt = "bch16";
> +        ti,elm-id = <&elm>;
> +        rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
> +      };
> +    };
> 


Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
deleted file mode 100644
index c1359f4d48d7..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
+++ /dev/null
@@ -1,157 +0,0 @@ 
-Device tree bindings for OMAP general purpose memory controllers (GPMC)
-
-The actual devices are instantiated from the child nodes of a GPMC node.
-
-Required properties:
-
- - compatible:		Should be set to one of the following:
-
-			ti,omap2420-gpmc (omap2420)
-			ti,omap2430-gpmc (omap2430)
-			ti,omap3430-gpmc (omap3430 & omap3630)
-			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
-			ti,am3352-gpmc   (am335x devices)
-
- - reg:			A resource specifier for the register space
-			(see the example below)
- - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
-			completed.
- - #address-cells:	Must be set to 2 to allow memory address translation
- - #size-cells:		Must be set to 1 to allow CS address passing
- - gpmc,num-cs:		The maximum number of chip-select lines that controller
-			can support.
- - gpmc,num-waitpins:	The maximum number of wait pins that controller can
-			support.
- - ranges:		Must be set up to reflect the memory layout with four
-			integer values for each chip-select line in use:
-
-			   <cs-number> 0 <physical address of mapping> <size>
-
-			Currently, calculated values derived from the contents
-			of the per-CS register GPMC_CONFIG7 (as set up by the
-			bootloader) are used for the physical address decoding.
-			As this will change in the future, filling correct
-			values here is a requirement.
- - interrupt-controller: The GPMC driver implements and interrupt controller for
-			the NAND events "fifoevent" and "termcount" plus the
-			rising/falling edges on the GPMC_WAIT pins.
-			The interrupt number mapping is as follows
-			0 - NAND_fifoevent
-			1 - NAND_termcount
-			2 - GPMC_WAIT0 pin edge
-			3 - GPMC_WAIT1 pin edge, and so on.
- - interrupt-cells:	Must be set to 2
- - gpio-controller:	The GPMC driver implements a GPIO controller for the
-			GPMC WAIT pins that can be used as general purpose inputs.
-			0 maps to GPMC_WAIT0 pin.
- - gpio-cells:		Must be set to 2
-
-Required properties when using NAND prefetch dma:
- - dmas			GPMC NAND prefetch dma channel
- - dma-names		Must be set to "rxtx"
-
-Timing properties for child nodes. All are optional and default to 0.
-
- - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
-
- Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
- - gpmc,cs-on-ns:	Assertion time
- - gpmc,cs-rd-off-ns:	Read deassertion time
- - gpmc,cs-wr-off-ns:	Write deassertion time
-
- ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
- - gpmc,adv-on-ns:	Assertion time
- - gpmc,adv-rd-off-ns:	Read deassertion time
- - gpmc,adv-wr-off-ns:	Write deassertion time
- - gpmc,adv-aad-mux-on-ns:	Assertion time for AAD
- - gpmc,adv-aad-mux-rd-off-ns:	Read deassertion time for AAD
- - gpmc,adv-aad-mux-wr-off-ns:	Write deassertion time for AAD
-
- WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- - gpmc,we-on-ns	Assertion time
- - gpmc,we-off-ns:	Deassertion time
-
- OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- - gpmc,oe-on-ns:	Assertion time
- - gpmc,oe-off-ns:	Deassertion time
- - gpmc,oe-aad-mux-on-ns:	Assertion time for AAD
- - gpmc,oe-aad-mux-off-ns:	Deassertion time for AAD
-
- Access time and cycle time timings (in nanoseconds) corresponding to
- GPMC_CONFIG5:
- - gpmc,page-burst-access-ns: 	Multiple access word delay
- - gpmc,access-ns:		Start-cycle to first data valid delay
- - gpmc,rd-cycle-ns:		Total read cycle time
- - gpmc,wr-cycle-ns:		Total write cycle time
- - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
- - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
- - gpmc,clk-activation-ns: 	GPMC clock activation time
- - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
-				data
-
-Boolean timing parameters. If property is present parameter enabled and
-disabled if omitted:
- - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
- - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
- - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
-				accesses to a different CS
- - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
-				accesses to the same CS
- - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
- - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
- - gpmc,time-para-granularity:	Multiply all access times by 2
-
-The following are only applicable to OMAP3+ and AM335x:
- - gpmc,wr-access-ns:		In synchronous write mode, for single or
-				burst accesses, defines the number of
-				GPMC_FCLK cycles from start access time
-				to the GPMC_CLK rising edge used by the
-				memory device for the first data capture.
- - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
-				the time when the first data is driven on
-				the address-data bus.
-
-GPMC chip-select settings properties for child nodes. All are optional.
-
-- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
-- gpmc,burst-wrap	Enables wrap bursting
-- gpmc,burst-read	Enables read page/burst mode
-- gpmc,burst-write	Enables write page/burst mode
-- gpmc,device-width	Total width of device(s) connected to a GPMC
-			chip-select in bytes. The GPMC supports 8-bit
-			and 16-bit devices and so this property must be
-			1 or 2.
-- gpmc,mux-add-data	Address and data multiplexing configuration.
-			Valid values are 1 for address-address-data
-			multiplexing mode and 2 for address-data
-			multiplexing mode.
-- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
-			is this is not set.
-- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
-			is this is not set.
-- gpmc,wait-pin		Wait-pin used by client. Must be less than
-			"gpmc,num-waitpins".
-- gpmc,wait-on-read	Enables wait monitoring on reads.
-- gpmc,wait-on-write	Enables wait monitoring on writes.
-
-Example for an AM33xx board:
-
-	gpmc: gpmc@50000000 {
-		compatible = "ti,am3352-gpmc";
-		ti,hwmods = "gpmc";
-		reg = <0x50000000 0x2000>;
-		interrupts = <100>;
-		dmas = <&edma 52 0>;
-		dma-names = "rxtx";
-		gpmc,num-cs = <8>;
-		gpmc,num-waitpins = <2>;
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		/* child nodes go here */
-	};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
new file mode 100644
index 000000000000..d6cd39bd3940
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
@@ -0,0 +1,172 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments GPMC Memory Controller device-tree bindings
+
+maintainers:
+  - Tony Lindgren <tony@atomide.com>
+  - Roger Quadros <rogerq@kernel.org>
+
+description:
+  The GPMC is a unified memory controller dedicated for interfacing
+  with external memory devices like
+  - Asynchronous SRAM-like memories and ASICs
+  - Asynchronous, synchronous, and page mode burst NOR flash
+  - NAND flash
+  - Pseudo-SRAM devices
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - ti,omap2420-gpmc
+          - ti,omap2430-gpmc
+          - ti,omap3430-gpmc
+          - ti,omap4430-gpmc
+          - ti,am3352-gpmc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: |
+      Functional clock. Used for bus timing calculations and
+      GPMC configuration.
+
+  clock-names:
+    items:
+      - const: fck
+
+  dmas:
+    items:
+      - description: DMA channel for GPMC NAND prefetch
+
+  dma-names:
+    items:
+      - const: rxtx
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  gpmc,num-cs:
+    description: maximum number of supported chip-select lines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  gpmc,num-waitpins:
+    description: maximum number of supported wait pins.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  ranges:
+    minItems: 1
+    description: |
+      Must be set up to reflect the memory layout with four
+      integer values for each chip-select line in use,
+      <cs-number> 0 <physical address of mapping> <size>
+    items:
+      - description: NAND bank 0
+      - description: NOR/SRAM bank 0
+      - description: NOR/SRAM bank 1
+
+  '#interrupt-cells':
+    const: 2
+
+  interrupt-controller:
+    description: |
+      The GPMC driver implements and interrupt controller for
+      the NAND events "fifoevent" and "termcount" plus the
+      rising/falling edges on the GPMC_WAIT pins.
+      The interrupt number mapping is as follows
+      0 - NAND_fifoevent
+      1 - NAND_termcount
+      2 - GPMC_WAIT0 pin edge
+      3 - GPMC_WAIT1 pin edge, and so on.
+
+  '#gpio-cells':
+    const: 2
+
+  gpio-controller:
+    description: |
+      The GPMC driver implements a GPIO controller for the
+      GPMC WAIT pins that can be used as general purpose inputs.
+      0 maps to GPMC_WAIT0 pin.
+
+  ti,hwmods:
+    description:
+      Name of the HWMOD associated with GPMC. This is for legacy
+      omap2/3 platforms only.
+    $ref: /schemas/types.yaml#/definitions/string
+    deprecated: true
+
+  ti,no-idle-on-init:
+    description:
+      Prevent idling the module at init. This is for legacy omap2/3
+      platforms only.
+    type: boolean
+    deprecated: true
+
+patternProperties:
+  "@[0-7],[a-f0-9]+$":
+    type: object
+    description: |
+      The child device node represents the device connected to the GPMC
+      bus. The device can be a NAND chip, SRAM device, NOR device
+      or an ASIC.
+
+    allOf:
+      - $ref: "ti,gpmc-child.yaml"
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpmc,num-cs
+  - gpmc,num-waitpins
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    gpmc: memory-controller@50000000 {
+      compatible = "ti,am3352-gpmc";
+      reg = <0x50000000 0x2000>;
+      interrupts = <100>;
+      clocks = <&l3s_clkctrl>;
+      clock-names = "fck";
+      dmas = <&edma 52 0>;
+      dma-names = "rxtx";
+      gpmc,num-cs = <8>;
+      gpmc,num-waitpins = <2>;
+      #address-cells = <2>;
+      #size-cells = <1>;
+      ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+      interrupt-controller;
+      #interrupt-cells = <2>;
+      gpio-controller;
+      #gpio-cells = <2>;
+
+      nand@0,0 {
+        compatible = "ti,omap2-nand";
+        reg = <0 0 4>;
+        interrupt-parent = <&gpmc>;
+        interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+                     <1 IRQ_TYPE_NONE>; /* termcount */
+        ti,nand-xfer-type = "prefetch-dma";
+        ti,nand-ecc-opt = "bch16";
+        ti,elm-id = <&elm>;
+        rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
+      };
+    };