diff mbox

[2/2] ARM: ux500: simplify secondary CPU boot

Message ID 1438586812-30164-1-git-send-email-linus.walleij@linaro.org
State Accepted
Commit c00def71efd919e8ae835a25f4f4c80a4b2d36d3
Headers show

Commit Message

Linus Walleij Aug. 3, 2015, 7:26 a.m. UTC
This removes a lot of ancient cruft from the Ux500 SMP boot.
Instead of the pen grab/release, just point the ROM to
secondary_boot() and start the second CPU there, then send
the IPI.

Use our own SMP enable method. This enables us to remove the
last static mapping and get both CPUs booting properly.

Tested this and it just works.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Hi ARM SoC folks: please apply this to fixes for v4.2. I was
intending it for v4.3 but we might as well just kill off the
legacy boot method right now so we do not need to restore any
static maps and undo the cleanup (which would be just as
invasive).
---
 arch/arm/mach-ux500/Makefile     |   2 +-
 arch/arm/mach-ux500/cpu-db8500.c |   1 -
 arch/arm/mach-ux500/headsmp.S    |  37 -----------
 arch/arm/mach-ux500/platsmp.c    | 132 ++++++++++++---------------------------
 arch/arm/mach-ux500/setup.h      |   1 -
 5 files changed, 40 insertions(+), 133 deletions(-)
 delete mode 100644 arch/arm/mach-ux500/headsmp.S

Comments

Linus Walleij Aug. 6, 2015, 2:40 p.m. UTC | #1
On Thu, Aug 6, 2015 at 10:11 AM, Olof Johansson <olof@lixom.net> wrote:
> On Mon, Aug 03, 2015 at 09:26:52AM +0200, Linus Walleij wrote:
>> This removes a lot of ancient cruft from the Ux500 SMP boot.
>> Instead of the pen grab/release, just point the ROM to
>> secondary_boot() and start the second CPU there, then send
>> the IPI.
>>
>> Use our own SMP enable method. This enables us to remove the
>> last static mapping and get both CPUs booting properly.
>>
>> Tested this and it just works.
>>
>> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>> ---
>> Hi ARM SoC folks: please apply this to fixes for v4.2. I was
>> intending it for v4.3 but we might as well just kill off the
>> legacy boot method right now so we do not need to restore any
>> static maps and undo the cleanup (which would be just as
>> invasive).
>
> It's a bit late in the cycle for that. I'll apply it in cleanup for 4.3 though.

OK I've got a bunch of cleanups for Ux500, shall I include these
in the pull request or will you apply this separately?

Yours,
Linus Walleij
diff mbox

Patch

diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index 4418a5078833..c8643ac5db71 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -7,7 +7,7 @@  obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
 obj-$(CONFIG_UX500_SOC_DB8500)	+= cpu-db8500.o
 obj-$(CONFIG_MACH_MOP500)	+= board-mop500-regulators.o \
 				board-mop500-audio.o
-obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
+obj-$(CONFIG_SMP)		+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
 obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o
 
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 16913800bbf9..ba708ce08616 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -154,7 +154,6 @@  static const char * stericsson_dt_platform_compat[] = {
 };
 
 DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
-	.smp            = smp_ops(ux500_smp_ops),
 	.map_io		= u8500_map_io,
 	.init_irq	= ux500_init_irq,
 	/* we re-use nomadik timer here */
diff --git a/arch/arm/mach-ux500/headsmp.S b/arch/arm/mach-ux500/headsmp.S
deleted file mode 100644
index 9cdea049485d..000000000000
--- a/arch/arm/mach-ux500/headsmp.S
+++ /dev/null
@@ -1,37 +0,0 @@ 
-/*
- *  Copyright (c) 2009 ST-Ericsson
- *	This file is based  ARM Realview platform
- *  Copyright (c) 2003 ARM Limited
- *  All Rights Reserved
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/linkage.h>
-#include <linux/init.h>
-
-/*
- * U8500 specific entry point for secondary CPUs.
- */
-ENTRY(u8500_secondary_startup)
-	mrc	p15, 0, r0, c0, c0, 5
-	and	r0, r0, #15
-	adr	r4, 1f
-	ldmia	r4, {r5, r6}
-	sub	r4, r4, r5
-	add	r6, r6, r4
-pen:	ldr	r7, [r6]
-	cmp	r7, r0
-	bne	pen
-
-	/*
-	 * we've been released from the holding pen: secondary_stack
-	 * should now contain the SVC stack for this core
-	 */
-	b	secondary_startup
-ENDPROC(u8500_secondary_startup)
-
-	.align 2
-1:	.long	.
-	.long	pen_release
diff --git a/arch/arm/mach-ux500/platsmp.c b/arch/arm/mach-ux500/platsmp.c
index 62b1de922bd8..70766b963758 100644
--- a/arch/arm/mach-ux500/platsmp.c
+++ b/arch/arm/mach-ux500/platsmp.c
@@ -28,135 +28,81 @@ 
 #include "db8500-regs.h"
 #include "id.h"
 
-static void __iomem *scu_base;
-static void __iomem *backupram;
-
-/* This is called from headsmp.S to wakeup the secondary core */
-extern void u8500_secondary_startup(void);
-
-/*
- * Write pen_release in a way that is guaranteed to be visible to all
- * observers, irrespective of whether they're taking part in coherency
- * or not.  This is necessary for the hotplug code to work reliably.
- */
-static void write_pen_release(int val)
-{
-	pen_release = val;
-	smp_wmb();
-	sync_cache_w(&pen_release);
-}
-
-static DEFINE_SPINLOCK(boot_lock);
-
-static void ux500_secondary_init(unsigned int cpu)
-{
-	/*
-	 * let the primary processor know we're out of the
-	 * pen, then head off into the C entry point
-	 */
-	write_pen_release(-1);
-
-	/*
-	 * Synchronise with the boot thread.
-	 */
-	spin_lock(&boot_lock);
-	spin_unlock(&boot_lock);
-}
+/* Magic triggers in backup RAM */
+#define UX500_CPU1_JUMPADDR_OFFSET 0x1FF4
+#define UX500_CPU1_WAKEMAGIC_OFFSET 0x1FF0
 
-static int ux500_boot_secondary(unsigned int cpu, struct task_struct *idle)
+static void wakeup_secondary(void)
 {
-	unsigned long timeout;
-
-	/*
-	 * set synchronisation state between this boot processor
-	 * and the secondary one
-	 */
-	spin_lock(&boot_lock);
-
-	/*
-	 * The secondary processor is waiting to be released from
-	 * the holding pen - release it, then wait for it to flag
-	 * that it has been released by resetting pen_release.
-	 */
-	write_pen_release(cpu_logical_map(cpu));
-
-	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+	struct device_node *np;
+	static void __iomem *backupram;
 
-	timeout = jiffies + (1 * HZ);
-	while (time_before(jiffies, timeout)) {
-		if (pen_release == -1)
-			break;
+	np = of_find_compatible_node(NULL, NULL, "ste,dbx500-backupram");
+	if (!np) {
+		pr_err("No backupram base address\n");
+		return;
+	}
+	backupram = of_iomap(np, 0);
+	of_node_put(np);
+	if (!backupram) {
+		pr_err("No backupram remap\n");
+		return;
 	}
 
 	/*
-	 * now the secondary core is starting up let it run its
-	 * calibrations, then wait for it to finish
-	 */
-	spin_unlock(&boot_lock);
-
-	return pen_release != -1 ? -ENOSYS : 0;
-}
-
-static void __init wakeup_secondary(void)
-{
-	/*
 	 * write the address of secondary startup into the backup ram register
 	 * at offset 0x1FF4, then write the magic number 0xA1FEED01 to the
 	 * backup ram register at offset 0x1FF0, which is what boot rom code
-	 * is waiting for. This would wake up the secondary core from WFE
+	 * is waiting for. This will wake up the secondary core from WFE.
 	 */
-#define UX500_CPU1_JUMPADDR_OFFSET 0x1FF4
-	__raw_writel(virt_to_phys(u8500_secondary_startup),
-		     backupram + UX500_CPU1_JUMPADDR_OFFSET);
-
-#define UX500_CPU1_WAKEMAGIC_OFFSET 0x1FF0
-	__raw_writel(0xA1FEED01,
-		     backupram + UX500_CPU1_WAKEMAGIC_OFFSET);
+	writel(virt_to_phys(secondary_startup),
+	       backupram + UX500_CPU1_JUMPADDR_OFFSET);
+	writel(0xA1FEED01,
+	       backupram + UX500_CPU1_WAKEMAGIC_OFFSET);
 
 	/* make sure write buffer is drained */
 	mb();
+	iounmap(backupram);
 }
 
-/*
- * Initialise the CPU possible map early - this describes the CPUs
- * which may be present or become present in the system.
- */
-static void __init ux500_smp_init_cpus(void)
+static void __init ux500_smp_prepare_cpus(unsigned int max_cpus)
 {
-	unsigned int i, ncores;
 	struct device_node *np;
+	static void __iomem *scu_base;
+	unsigned int ncores;
+	int i;
 
 	np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-scu");
+	if (!np) {
+		pr_err("No SCU base address\n");
+		return;
+	}
 	scu_base = of_iomap(np, 0);
 	of_node_put(np);
-	if (!scu_base)
+	if (!scu_base) {
+		pr_err("No SCU remap\n");
 		return;
-	backupram = ioremap(U8500_BACKUPRAM0_BASE, SZ_8K);
-	ncores = scu_get_core_count(scu_base);
-
-	/* sanity check */
-	if (ncores > nr_cpu_ids) {
-		pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
-			ncores, nr_cpu_ids);
-		ncores = nr_cpu_ids;
 	}
 
+	scu_enable(scu_base);
+	ncores = scu_get_core_count(scu_base);
 	for (i = 0; i < ncores; i++)
 		set_cpu_possible(i, true);
+	iounmap(scu_base);
 }
 
-static void __init ux500_smp_prepare_cpus(unsigned int max_cpus)
+static int ux500_boot_secondary(unsigned int cpu, struct task_struct *idle)
 {
-	scu_enable(scu_base);
 	wakeup_secondary();
+	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+	return 0;
 }
 
 struct smp_operations ux500_smp_ops __initdata = {
-	.smp_init_cpus		= ux500_smp_init_cpus,
 	.smp_prepare_cpus	= ux500_smp_prepare_cpus,
-	.smp_secondary_init	= ux500_secondary_init,
 	.smp_boot_secondary	= ux500_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= ux500_cpu_die,
 #endif
 };
+CPU_METHOD_OF_DECLARE(ux500_smp, "ste,dbx500-smp", &ux500_smp_ops);
diff --git a/arch/arm/mach-ux500/setup.h b/arch/arm/mach-ux500/setup.h
index 1fb6ad2789f1..65876eac0761 100644
--- a/arch/arm/mach-ux500/setup.h
+++ b/arch/arm/mach-ux500/setup.h
@@ -26,7 +26,6 @@  extern struct device *ux500_soc_device_init(const char *soc_id);
 
 extern void ux500_timer_init(void);
 
-extern struct smp_operations ux500_smp_ops;
 extern void ux500_cpu_die(unsigned int cpu);
 
 #endif /*  __ASM_ARCH_SETUP_H */