diff mbox series

[v2,05/14] dt-bindings: gpio: Convert Broadcom STB GPIO to YAML

Message ID 20211206182616.2089677-6-f.fainelli@gmail.com
State Superseded
Headers show
Series Broadcom DT bindings updates to YAML | expand

Commit Message

Florian Fainelli Dec. 6, 2021, 6:26 p.m. UTC
Convert the Broadcom STB GPIO Device Tree binding to YAML to help with
validation.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
 .../bindings/gpio/brcm,brcmstb-gpio.txt       |  83 --------------
 .../bindings/gpio/brcm,brcmstb-gpio.yaml      | 105 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 106 insertions(+), 84 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
 create mode 100644 Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml

Comments

Rob Herring (Arm) Dec. 7, 2021, 2:58 p.m. UTC | #1
On Mon, 06 Dec 2021 10:26:07 -0800, Florian Fainelli wrote:
> Convert the Broadcom STB GPIO Device Tree binding to YAML to help with
> validation.
> 
> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
> ---
>  .../bindings/gpio/brcm,brcmstb-gpio.txt       |  83 --------------
>  .../bindings/gpio/brcm,brcmstb-gpio.yaml      | 105 ++++++++++++++++++
>  MAINTAINERS                                   |   2 +-
>  3 files changed, 106 insertions(+), 84 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
>  create mode 100644 Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml
> 

Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.

Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.

Full log is available here: https://patchwork.ozlabs.org/patch/1564132


gpio@4172c0: interrupts-extended: [[6, 6], [7, 5]] is too long
	arch/arm/boot/dts/bcm7445-bcm97445svmb.dt.yaml
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
deleted file mode 100644
index 5d468ecd1809..000000000000
--- a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
+++ /dev/null
@@ -1,83 +0,0 @@ 
-Broadcom STB "UPG GIO" GPIO controller
-
-The controller's registers are organized as sets of eight 32-bit
-registers with each set controlling a bank of up to 32 pins.  A single
-interrupt is shared for all of the banks handled by the controller.
-
-Required properties:
-
-- compatible:
-    Must be "brcm,brcmstb-gpio"
-
-- reg:
-    Define the base and range of the I/O address space containing
-    the brcmstb GPIO controller registers
-
-- #gpio-cells:
-    Should be <2>.  The first cell is the pin number (within the controller's
-    pin space), and the second is used for the following:
-    bit[0]: polarity (0 for active-high, 1 for active-low)
-
-- gpio-controller:
-    Specifies that the node is a GPIO controller.
-
-- brcm,gpio-bank-widths:
-    Number of GPIO lines for each bank.  Number of elements must
-    correspond to number of banks suggested by the 'reg' property.
-
-Optional properties:
-
-- interrupts:
-    The interrupt shared by all GPIO lines for this controller.
-
-- interrupts-extended:
-    Alternate form of specifying interrupts and parents that allows for
-    multiple parents.  This takes precedence over 'interrupts' and
-    'interrupt-parent'.  Wakeup-capable GPIO controllers often route their
-    wakeup interrupt lines through a different interrupt controller than the
-    primary interrupt line, making this property necessary.
-
-- #interrupt-cells:
-    Should be <2>.  The first cell is the GPIO number, the second should specify
-    flags.  The following subset of flags is supported:
-    - bits[3:0] trigger type and level flags
-        1 = low-to-high edge triggered
-        2 = high-to-low edge triggered
-        4 = active high level-sensitive
-        8 = active low level-sensitive
-      Valid combinations are 1, 2, 3, 4, 8.
-    See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-- interrupt-controller:
-    Marks the device node as an interrupt controller
-
-- wakeup-source:
-    GPIOs for this controller can be used as a wakeup source
-
-Example:
-	upg_gio: gpio@f040a700 {
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-		compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
-		gpio-controller;
-		interrupt-controller;
-		reg = <0xf040a700 0x80>;
-		interrupt-parent = <&irq0_intc>;
-		interrupts = <0x6>;
-		brcm,gpio-bank-widths = <32 32 32 24>;
-	};
-
-	upg_gio_aon: gpio@f04172c0 {
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-		compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
-		gpio-controller;
-		interrupt-controller;
-		reg = <0xf04172c0 0x40>;
-		interrupt-parent = <&irq0_aon_intc>;
-		interrupts = <0x6>;
-		interrupts-extended = <&irq0_aon_intc 0x6>,
-			<&aon_pm_l2_intc 0x5>;
-		wakeup-source;
-		brcm,gpio-bank-widths = <18 4>;
-	};
diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml
new file mode 100644
index 000000000000..8c27932df2c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml
@@ -0,0 +1,105 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/brcm,brcmstb-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom STB "UPG GIO" GPIO controller
+
+description: >
+  The controller's registers are organized as sets of eight 32-bit
+  registers with each set controlling a bank of up to 32 pins.  A single
+  interrupt is shared for all of the banks handled by the controller.
+
+maintainers:
+  - Doug Berger <opendmb@gmail.com>
+  - Florian Fainelli <f.fainelli@gmail.com>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - brcm,bcm7445-gpio
+          - const: brcm,brcmstb-gpio
+
+  reg:
+    maxItems: 1
+    description: >
+      Define the base and range of the I/O address space containing
+      the brcmstb GPIO controller registers
+
+  "#gpio-cells":
+    const: 2
+    description: >
+      The first cell is the pin number (within the controller's
+      pin space), and the second is used for the following:
+      bit[0]: polarity (0 for active-high, 1 for active-low)
+
+  gpio-controller: true
+
+  "brcm,gpio-bank-widths":
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: >
+      Number of GPIO lines for each bank.  Number of elements must
+      correspond to number of banks suggested by the 'reg' property.
+
+  interrupts:
+    maxItems: 1
+    description: >
+      The interrupt shared by all GPIO lines for this controller.
+
+  "#interrupt-cells":
+    const: 2
+    description: |
+      The first cell is the GPIO number, the second should specify
+      flags.  The following subset of flags is supported:
+      - bits[3:0] trigger type and level flags
+        1 = low-to-high edge triggered
+        2 = high-to-low edge triggered
+        4 = active high level-sensitive
+        8 = active low level-sensitive
+      Valid combinations are 1, 2, 3, 4, 8.
+
+  interrupt-controller: true
+
+  wakeup-source:
+    type: boolean
+    description: >
+      GPIOs for this controller can be used as a wakeup source
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - "#gpio-cells"
+  - "brcm,gpio-bank-widths"
+
+additionalProperties: false
+
+examples:
+  - |
+    upg_gio: gpio@f040a700 {
+        #gpio-cells = <2>;
+        #interrupt-cells = <2>;
+        compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+        gpio-controller;
+        interrupt-controller;
+        reg = <0xf040a700 0x80>;
+        interrupt-parent = <&irq0_intc>;
+        interrupts = <0x6>;
+        brcm,gpio-bank-widths = <32 32 32 24>;
+    };
+
+    upg_gio_aon: gpio@f04172c0 {
+        #gpio-cells = <2>;
+        #interrupt-cells = <2>;
+        compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+        gpio-controller;
+        interrupt-controller;
+        reg = <0xf04172c0 0x40>;
+        interrupt-parent = <&irq0_aon_intc>;
+        interrupts = <0x6>;
+        wakeup-source;
+        brcm,gpio-bank-widths = <18 4>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 7a2345ce8521..9ac67c885159 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3761,7 +3761,7 @@  BROADCOM BRCMSTB GPIO DRIVER
 M:	Gregory Fong <gregory.0xf0@gmail.com>
 L:	bcm-kernel-feedback-list@broadcom.com
 S:	Supported
-F:	Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
+F:	Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.yaml
 F:	drivers/gpio/gpio-brcmstb.c
 
 BROADCOM BRCMSTB I2C DRIVER