| Message ID | 1441135938-8056-4-git-send-email-vaibhav.hiremath@linaro.org |
|---|---|
| State | New |
| Headers | show |
On 2015/9/2 3:32, Vaibhav Hiremath wrote: > In case PXA1928 family of devices, there is device/controller specific > configuration to control voltage/power on the IO pins. > > This patch implements and enables the sdhci_ops->voltage_switch() > callback api. > Note that IO pad register addresses are fetched as a memory resource. > > For example, in case of PXA1928 and family of devices, the DT property > would look something like, > > sdh1: sdh@d4280000 { > compatible = "mrvl,pxav3-mmc"; > reg-names = "sdhci", "io-pwr", "io-pwr-lock-unlock"; > reg = <0xd4280000 0x120>, > <0xd401e81c 4>, > <0xd4015068 8>; > ... > }; > > Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> > --- > drivers/mmc/host/sdhci-pxav3.c | 59 ++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 59 insertions(+) > > diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c > index 5d26fe0..cebb2f9 100644 > --- a/drivers/mmc/host/sdhci-pxav3.c > +++ b/drivers/mmc/host/sdhci-pxav3.c > @@ -63,11 +63,18 @@ > #define IO_PWR_AKEY_ASSAR 0xeb10 > #define IO_PWR_MMC1_PAD_1V8 BIT(2) > > +/* IO Power control */ > +#define IO_PWR_AKEY_ASFAR 0xbaba > +#define IO_PWR_AKEY_ASSAR 0xeb10 > +#define IO_PWR_MMC1_PAD_1V8 BIT(2) > + > struct sdhci_pxa { > struct clk *clk_core; > struct clk *clk_io; > u8 power_mode; > void __iomem *sdio3_conf_reg; > + void __iomem *io_pwr_reg; > + void __iomem *io_pwr_lock_reg; > }; > > /* > @@ -307,6 +314,38 @@ static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) > __func__, uhs, ctrl_2); > } > > +static void pxav3_voltage_switch(struct sdhci_host *host, > + u8 signal_voltage) > +{ > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > + struct sdhci_pxa *pxa = pltfm_host->priv; > + unsigned int val; > + > + if (!pxa->io_pwr_reg || !pxa->io_pwr_lock_reg) > + return; > + > + /* Lock register is 64 bit: First & Second access register */ > + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); > + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); > + val = readl(pxa->io_pwr_reg); > + > + switch (signal_voltage) { > + case MMC_SIGNAL_VOLTAGE_180: > + case MMC_SIGNAL_VOLTAGE_120: > + val |= IO_PWR_MMC1_PAD_1V8; > + break; > + case MMC_SIGNAL_VOLTAGE_330: > + default: > + val &= ~IO_PWR_MMC1_PAD_1V8; > + break; > + } > + > + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); > + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); > + > + writel(val, pxa->io_pwr_reg); > +} > + > static const struct sdhci_ops pxav3_sdhci_ops = { > .set_clock = sdhci_set_clock, > .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, > @@ -314,6 +353,7 @@ static const struct sdhci_ops pxav3_sdhci_ops = { > .set_bus_width = sdhci_set_bus_width, > .reset = pxav3_reset, > .set_uhs_signaling = pxav3_set_uhs_signaling, > + .voltage_switch = pxav3_voltage_switch, > }; > > static struct sdhci_pltfm_data sdhci_pxav3_pdata = { > @@ -368,6 +408,7 @@ static int sdhci_pxav3_probe(struct platform_device *pdev) > struct sdhci_host *host = NULL; > struct sdhci_pxa *pxa = NULL; > const struct of_device_id *match; > + struct resource *res; > int ret; > > pxa = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_pxa), GFP_KERNEL); > @@ -408,6 +449,24 @@ static int sdhci_pxav3_probe(struct platform_device *pdev) > goto err_mbus_win; > } > > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "io-pwr-conf"); > + if (res) { > + pxa->io_pwr_reg = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(pxa->io_pwr_reg)) { > + ret = PTR_ERR(pxa->io_pwr_reg); > + goto err_mbus_win; > + } > + } Hi Vaibhav, Why not get it from syscon and use regmap API to deal with it. IMO, that's okay, you can find examples from drivers/mmc/host/dw_mmc-k3.c: dw_mci_hi6220_switch_voltage > + > + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "io-pwr-lock-unlock"); > + if (res) { > + pxa->io_pwr_lock_reg = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(pxa->io_pwr_lock_reg)) { > + ret = PTR_ERR(pxa->io_pwr_lock_reg); > + goto err_mbus_win; > + } > + } > + > match = of_match_device(of_match_ptr(sdhci_pxav3_of_match), &pdev->dev); > if (match) { > ret = mmc_of_parse(host->mmc); >
On Wednesday 02 September 2015 07:21 PM, Shawn Lin wrote: > On 2015/9/2 3:32, Vaibhav Hiremath wrote: >> In case PXA1928 family of devices, there is device/controller specific >> configuration to control voltage/power on the IO pins. >> >> This patch implements and enables the sdhci_ops->voltage_switch() >> callback api. >> Note that IO pad register addresses are fetched as a memory resource. >> >> For example, in case of PXA1928 and family of devices, the DT property >> would look something like, >> >> sdh1: sdh@d4280000 { >> compatible = "mrvl,pxav3-mmc"; >> reg-names = "sdhci", "io-pwr", "io-pwr-lock-unlock"; >> reg = <0xd4280000 0x120>, >> <0xd401e81c 4>, >> <0xd4015068 8>; >> ... >> }; >> >> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> >> --- >> drivers/mmc/host/sdhci-pxav3.c | 59 >> ++++++++++++++++++++++++++++++++++++++++++ >> 1 file changed, 59 insertions(+) >> >> diff --git a/drivers/mmc/host/sdhci-pxav3.c >> b/drivers/mmc/host/sdhci-pxav3.c >> index 5d26fe0..cebb2f9 100644 >> --- a/drivers/mmc/host/sdhci-pxav3.c >> +++ b/drivers/mmc/host/sdhci-pxav3.c >> @@ -63,11 +63,18 @@ >> #define IO_PWR_AKEY_ASSAR 0xeb10 >> #define IO_PWR_MMC1_PAD_1V8 BIT(2) >> >> +/* IO Power control */ >> +#define IO_PWR_AKEY_ASFAR 0xbaba >> +#define IO_PWR_AKEY_ASSAR 0xeb10 >> +#define IO_PWR_MMC1_PAD_1V8 BIT(2) >> + >> struct sdhci_pxa { >> struct clk *clk_core; >> struct clk *clk_io; >> u8 power_mode; >> void __iomem *sdio3_conf_reg; >> + void __iomem *io_pwr_reg; >> + void __iomem *io_pwr_lock_reg; >> }; >> >> /* >> @@ -307,6 +314,38 @@ static void pxav3_set_uhs_signaling(struct >> sdhci_host *host, unsigned int uhs) >> __func__, uhs, ctrl_2); >> } >> >> +static void pxav3_voltage_switch(struct sdhci_host *host, >> + u8 signal_voltage) >> +{ >> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); >> + struct sdhci_pxa *pxa = pltfm_host->priv; >> + unsigned int val; >> + >> + if (!pxa->io_pwr_reg || !pxa->io_pwr_lock_reg) >> + return; >> + >> + /* Lock register is 64 bit: First & Second access register */ >> + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); >> + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); >> + val = readl(pxa->io_pwr_reg); >> + >> + switch (signal_voltage) { >> + case MMC_SIGNAL_VOLTAGE_180: >> + case MMC_SIGNAL_VOLTAGE_120: >> + val |= IO_PWR_MMC1_PAD_1V8; >> + break; >> + case MMC_SIGNAL_VOLTAGE_330: >> + default: >> + val &= ~IO_PWR_MMC1_PAD_1V8; >> + break; >> + } >> + >> + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); >> + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); >> + >> + writel(val, pxa->io_pwr_reg); >> +} >> + >> static const struct sdhci_ops pxav3_sdhci_ops = { >> .set_clock = sdhci_set_clock, >> .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, >> @@ -314,6 +353,7 @@ static const struct sdhci_ops pxav3_sdhci_ops = { >> .set_bus_width = sdhci_set_bus_width, >> .reset = pxav3_reset, >> .set_uhs_signaling = pxav3_set_uhs_signaling, >> + .voltage_switch = pxav3_voltage_switch, >> }; >> >> static struct sdhci_pltfm_data sdhci_pxav3_pdata = { >> @@ -368,6 +408,7 @@ static int sdhci_pxav3_probe(struct >> platform_device *pdev) >> struct sdhci_host *host = NULL; >> struct sdhci_pxa *pxa = NULL; >> const struct of_device_id *match; >> + struct resource *res; >> int ret; >> >> pxa = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_pxa), >> GFP_KERNEL); >> @@ -408,6 +449,24 @@ static int sdhci_pxav3_probe(struct >> platform_device *pdev) >> goto err_mbus_win; >> } >> >> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, >> "io-pwr-conf"); >> + if (res) { >> + pxa->io_pwr_reg = devm_ioremap_resource(&pdev->dev, res); >> + if (IS_ERR(pxa->io_pwr_reg)) { >> + ret = PTR_ERR(pxa->io_pwr_reg); >> + goto err_mbus_win; >> + } >> + } > > Hi Vaibhav, > > Why not get it from syscon and use regmap API to deal with it. > IMO, that's okay, you can find examples from > drivers/mmc/host/dw_mmc-k3.c: dw_mci_hi6220_switch_voltage > > Thanks Shawn, Good to know that, something similar is already in the mainline. Quickly looked into the driver, and I think it looks ok and doable. I will for couple of days, to see whether I get further comments and then spin next version. Thanks, Vaibhav -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wednesday 02 September 2015 07:21 PM, Shawn Lin wrote: > On 2015/9/2 3:32, Vaibhav Hiremath wrote: >> In case PXA1928 family of devices, there is device/controller specific >> configuration to control voltage/power on the IO pins. >> >> This patch implements and enables the sdhci_ops->voltage_switch() >> callback api. >> Note that IO pad register addresses are fetched as a memory resource. >> >> For example, in case of PXA1928 and family of devices, the DT property >> would look something like, >> >> sdh1: sdh@d4280000 { >> compatible = "mrvl,pxav3-mmc"; >> reg-names = "sdhci", "io-pwr", "io-pwr-lock-unlock"; >> reg = <0xd4280000 0x120>, >> <0xd401e81c 4>, >> <0xd4015068 8>; >> ... >> }; >> >> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> >> --- >> drivers/mmc/host/sdhci-pxav3.c | 59 >> ++++++++++++++++++++++++++++++++++++++++++ >> 1 file changed, 59 insertions(+) >> >> diff --git a/drivers/mmc/host/sdhci-pxav3.c >> b/drivers/mmc/host/sdhci-pxav3.c >> index 5d26fe0..cebb2f9 100644 >> --- a/drivers/mmc/host/sdhci-pxav3.c >> +++ b/drivers/mmc/host/sdhci-pxav3.c >> @@ -63,11 +63,18 @@ >> #define IO_PWR_AKEY_ASSAR 0xeb10 >> #define IO_PWR_MMC1_PAD_1V8 BIT(2) >> >> +/* IO Power control */ >> +#define IO_PWR_AKEY_ASFAR 0xbaba >> +#define IO_PWR_AKEY_ASSAR 0xeb10 >> +#define IO_PWR_MMC1_PAD_1V8 BIT(2) >> + >> struct sdhci_pxa { >> struct clk *clk_core; >> struct clk *clk_io; >> u8 power_mode; >> void __iomem *sdio3_conf_reg; >> + void __iomem *io_pwr_reg; >> + void __iomem *io_pwr_lock_reg; >> }; >> >> /* >> @@ -307,6 +314,38 @@ static void pxav3_set_uhs_signaling(struct >> sdhci_host *host, unsigned int uhs) >> __func__, uhs, ctrl_2); >> } >> >> +static void pxav3_voltage_switch(struct sdhci_host *host, >> + u8 signal_voltage) >> +{ >> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); >> + struct sdhci_pxa *pxa = pltfm_host->priv; >> + unsigned int val; >> + >> + if (!pxa->io_pwr_reg || !pxa->io_pwr_lock_reg) >> + return; >> + >> + /* Lock register is 64 bit: First & Second access register */ >> + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); >> + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); >> + val = readl(pxa->io_pwr_reg); >> + >> + switch (signal_voltage) { >> + case MMC_SIGNAL_VOLTAGE_180: >> + case MMC_SIGNAL_VOLTAGE_120: >> + val |= IO_PWR_MMC1_PAD_1V8; >> + break; >> + case MMC_SIGNAL_VOLTAGE_330: >> + default: >> + val &= ~IO_PWR_MMC1_PAD_1V8; >> + break; >> + } >> + >> + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); >> + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); >> + >> + writel(val, pxa->io_pwr_reg); >> +} >> + >> static const struct sdhci_ops pxav3_sdhci_ops = { >> .set_clock = sdhci_set_clock, >> .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, >> @@ -314,6 +353,7 @@ static const struct sdhci_ops pxav3_sdhci_ops = { >> .set_bus_width = sdhci_set_bus_width, >> .reset = pxav3_reset, >> .set_uhs_signaling = pxav3_set_uhs_signaling, >> + .voltage_switch = pxav3_voltage_switch, >> }; >> >> static struct sdhci_pltfm_data sdhci_pxav3_pdata = { >> @@ -368,6 +408,7 @@ static int sdhci_pxav3_probe(struct >> platform_device *pdev) >> struct sdhci_host *host = NULL; >> struct sdhci_pxa *pxa = NULL; >> const struct of_device_id *match; >> + struct resource *res; >> int ret; >> >> pxa = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_pxa), >> GFP_KERNEL); >> @@ -408,6 +449,24 @@ static int sdhci_pxav3_probe(struct >> platform_device *pdev) >> goto err_mbus_win; >> } >> >> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, >> "io-pwr-conf"); >> + if (res) { >> + pxa->io_pwr_reg = devm_ioremap_resource(&pdev->dev, res); >> + if (IS_ERR(pxa->io_pwr_reg)) { >> + ret = PTR_ERR(pxa->io_pwr_reg); >> + goto err_mbus_win; >> + } >> + } > > Hi Vaibhav, > > Why not get it from syscon and use regmap API to deal with it. > IMO, that's okay, you can find examples from > drivers/mmc/host/dw_mmc-k3.c: dw_mci_hi6220_switch_voltage > > After looking more into this, things are not looking good to me - PXA1928 (thats what I have details for) has different needs here, The lock/unlock register located in apbc_clocks register space, and sysconf will not be right place for it. I think the approach which I took in this series looks better to me :) Thanks, Vaibhav -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c index 5d26fe0..cebb2f9 100644 --- a/drivers/mmc/host/sdhci-pxav3.c +++ b/drivers/mmc/host/sdhci-pxav3.c @@ -63,11 +63,18 @@ #define IO_PWR_AKEY_ASSAR 0xeb10 #define IO_PWR_MMC1_PAD_1V8 BIT(2) +/* IO Power control */ +#define IO_PWR_AKEY_ASFAR 0xbaba +#define IO_PWR_AKEY_ASSAR 0xeb10 +#define IO_PWR_MMC1_PAD_1V8 BIT(2) + struct sdhci_pxa { struct clk *clk_core; struct clk *clk_io; u8 power_mode; void __iomem *sdio3_conf_reg; + void __iomem *io_pwr_reg; + void __iomem *io_pwr_lock_reg; }; /* @@ -307,6 +314,38 @@ static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) __func__, uhs, ctrl_2); } +static void pxav3_voltage_switch(struct sdhci_host *host, + u8 signal_voltage) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_pxa *pxa = pltfm_host->priv; + unsigned int val; + + if (!pxa->io_pwr_reg || !pxa->io_pwr_lock_reg) + return; + + /* Lock register is 64 bit: First & Second access register */ + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); + val = readl(pxa->io_pwr_reg); + + switch (signal_voltage) { + case MMC_SIGNAL_VOLTAGE_180: + case MMC_SIGNAL_VOLTAGE_120: + val |= IO_PWR_MMC1_PAD_1V8; + break; + case MMC_SIGNAL_VOLTAGE_330: + default: + val &= ~IO_PWR_MMC1_PAD_1V8; + break; + } + + writel(IO_PWR_AKEY_ASFAR, pxa->io_pwr_lock_reg); + writel(IO_PWR_AKEY_ASSAR, pxa->io_pwr_lock_reg + 4); + + writel(val, pxa->io_pwr_reg); +} + static const struct sdhci_ops pxav3_sdhci_ops = { .set_clock = sdhci_set_clock, .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, @@ -314,6 +353,7 @@ static const struct sdhci_ops pxav3_sdhci_ops = { .set_bus_width = sdhci_set_bus_width, .reset = pxav3_reset, .set_uhs_signaling = pxav3_set_uhs_signaling, + .voltage_switch = pxav3_voltage_switch, }; static struct sdhci_pltfm_data sdhci_pxav3_pdata = { @@ -368,6 +408,7 @@ static int sdhci_pxav3_probe(struct platform_device *pdev) struct sdhci_host *host = NULL; struct sdhci_pxa *pxa = NULL; const struct of_device_id *match; + struct resource *res; int ret; pxa = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_pxa), GFP_KERNEL); @@ -408,6 +449,24 @@ static int sdhci_pxav3_probe(struct platform_device *pdev) goto err_mbus_win; } + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "io-pwr-conf"); + if (res) { + pxa->io_pwr_reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(pxa->io_pwr_reg)) { + ret = PTR_ERR(pxa->io_pwr_reg); + goto err_mbus_win; + } + } + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "io-pwr-lock-unlock"); + if (res) { + pxa->io_pwr_lock_reg = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(pxa->io_pwr_lock_reg)) { + ret = PTR_ERR(pxa->io_pwr_lock_reg); + goto err_mbus_win; + } + } + match = of_match_device(of_match_ptr(sdhci_pxav3_of_match), &pdev->dev); if (match) { ret = mmc_of_parse(host->mmc);
In case PXA1928 family of devices, there is device/controller specific configuration to control voltage/power on the IO pins. This patch implements and enables the sdhci_ops->voltage_switch() callback api. Note that IO pad register addresses are fetched as a memory resource. For example, in case of PXA1928 and family of devices, the DT property would look something like, sdh1: sdh@d4280000 { compatible = "mrvl,pxav3-mmc"; reg-names = "sdhci", "io-pwr", "io-pwr-lock-unlock"; reg = <0xd4280000 0x120>, <0xd401e81c 4>, <0xd4015068 8>; ... }; Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org> --- drivers/mmc/host/sdhci-pxav3.c | 59 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+)