diff mbox

[2/2] ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board

Message ID 1442011005-4828-2-git-send-email-sjoerd.simons@collabora.co.uk
State New
Headers show

Commit Message

Sjoerd Simons Sept. 11, 2015, 10:36 p.m. UTC
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.

Currently supported are serial console, wired networking, hdmi output
and USB.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>

---

 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/rk3288-rock2-som.dtsi   | 267 ++++++++++++++++++++++++++++++
 arch/arm/boot/dts/rk3288-rock2-square.dts | 164 ++++++++++++++++++
 3 files changed, 432 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-rock2-som.dtsi
 create mode 100644 arch/arm/boot/dts/rk3288-rock2-square.dts

Comments

Heiko Stuebner Sept. 13, 2015, 4:47 p.m. UTC | #1
Hi Sjoerd,

Am Samstag, 12. September 2015, 00:36:45 schrieb Sjoerd Simons:
> The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
> with the Square baseboard. Add a dtsi for the SoM which can be included
> into the dts for the various baseboards (e.g. full and square) and a dts
> for the square board.
> 
> Currently supported are serial console, wired networking, hdmi output
> and USB.
> 
> Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
> 
> ---
> 
>  arch/arm/boot/dts/Makefile                |   1 +
>  arch/arm/boot/dts/rk3288-rock2-som.dtsi   | 267
> ++++++++++++++++++++++++++++++ arch/arm/boot/dts/rk3288-rock2-square.dts |
> 164 ++++++++++++++++++ 3 files changed, 432 insertions(+)

please add an entry to Documentation/devicetree/arm/rockchip.txt for the new 
board too.

Some more nitpicks below:


>  create mode 100644 arch/arm/boot/dts/rk3288-rock2-som.dtsi
>  create mode 100644 arch/arm/boot/dts/rk3288-rock2-square.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 233159d..1ed8ec1 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -507,6 +507,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
>  	rk3288-firefly-beta.dtb \
>  	rk3288-firefly.dtb \
>  	rk3288-r89.dtb \
> +	rk3288-rock2-square.dtb \
>  	rk3288-veyron-jerry.dtb \
>  	rk3288-veyron-minnie.dtb \
>  	rk3288-veyron-pinky.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi
> b/arch/arm/boot/dts/rk3288-rock2-som.dtsi new file mode 100644
> index 0000000..01e69e8
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
> @@ -0,0 +1,267 @@
> +/*
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/pwm/pwm.h>
> +#include "rk3288.dtsi"
> +
> +/ {
> +	memory {
> +		device_type = "memory";
> +		reg = <0x0 0x80000000>;

please swap those if possible. I try to keep the ordering like
- compatible
- reg
[alphabetic sorted]
- status

for ease of reading.


> +	};
> +
> +	ext_gmac: external-gmac-clock {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <125000000>;
> +		clock-output-names = "ext_gmac";
> +	};
> +
> +	vcc_sys: vsys-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_sys";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&cpu0 {
> +	cpu0-supply = <&vdd_cpu>;
> +};
> +
> +

double empty line


> +&emmc {
> +	broken-cd;
[...]
> +	non-removable;

Documentation/devicetree/bindings/mmc/mmc.txt:
"Only one of the properties in this section should be supplied"

so I guess non-removable would be the most suitable


> +	num-slots = <1>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
> +	vmmc-supply = <&vcc_io>;
> +	status = "okay";
> +};
> +
> +&gmac {
> +	assigned-clocks = <&cru SCLK_MAC>;
> +	assigned-clock-parents = <&ext_gmac>;
> +	clock_in_out = "input";
> +	phy-mode = "rgmii";
> +	phy-supply = <&vccio_pmu>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&rgmii_pins &phy_rst>;
> +	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	snps,reset-delays-us = <0 10000 30000>;
> +	rx_delay = <0x10>;
> +	tx_delay = <0x30>;
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	act8846: act8846@5a {
> +		compatible = "active-semi,act8846";
> +		reg = <0x5a>;
> +		inl1-supply = <&vcc_io>;
> +		inl2-supply = <&vcc_sys>;
> +		inl3-supply = <&vcc_20>;
> +		vp1-supply = <&vcc_sys>;
> +		vp2-supply = <&vcc_sys>;
> +		vp3-supply = <&vcc_sys>;
> +		vp4-supply = <&vcc_sys>;
> +		status = "okay";

you're just adding it here, so I guess it doesn't necessarily need a "status 
okay"

[...]

> +	gmac {
> +		phy_rst: phy-rst {
> +			rockchip,pins = <RK_GPIO4 8 RK_FUNC_GPIO  &pcfg_output_high>;
> +		};
> +	};
> +};
> +
> +

double empty line


> +&vopb {
> +	status = "okay";
> +};
> +
> +&vopb_mmu {
> +	status = "okay";
> +};
> +
> +&vopl {
> +	status = "okay";
> +};
> +
> +&vopl_mmu {
> +	status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts
> b/arch/arm/boot/dts/rk3288-rock2-square.dts new file mode 100644

[...]

> +	vcc_usb_host: vcc-host-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&host_vbus_drv>;
> +		/* Always on as the rockchip usb phy doesn't have a vbus-supply
> +		 * property */

comment style is off. Either one-line, like
	/* foo */
or multiline
	/*
	  * foo
	  */


Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Heiko Stuebner Sept. 13, 2015, 4:59 p.m. UTC | #2
Hi Sjoerd,

Am Samstag, 12. September 2015, 00:36:45 schrieb Sjoerd Simons:

one thing I forgot:

> +&emmc {
> +	broken-cd;
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	disable-wp;
> +	non-removable;
> +	num-slots = <1>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
> +	vmmc-supply = <&vcc_io>;
> +	status = "okay";
> +};

this could probably use a mmc powersequence to handle the emmc-reset pin?


Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Javier Martinez Canillas Sept. 13, 2015, 11 p.m. UTC | #3
Hello Sjoerd,

On Sat, Sep 12, 2015 at 12:36 AM, Sjoerd Simons
<sjoerd.simons@collabora.co.uk> wrote:

[snip]

> +
> +               regulators {
> +                       vcc_ddr: REG1 {
> +                               regulator-name = "VCC_DDR";
> +                               regulator-min-microvolt = <1200000>;
> +                               regulator-max-microvolt = <1200000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcc_io: REG2 {
> +                               regulator-name = "VCC_IO";
> +                               regulator-min-microvolt = <3300000>;
> +                               regulator-max-microvolt = <3300000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vdd_log: REG3 {
> +                               regulator-name = "VDD_LOG";
> +                               regulator-min-microvolt = <1000000>;
> +                               regulator-max-microvolt = <1000000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcc_20: REG4 {
> +                               regulator-name = "VCC_20";
> +                               regulator-min-microvolt = <2000000>;
> +                               regulator-max-microvolt = <2000000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vccio_sd: REG5 {
> +                               regulator-name = "VCCIO_SD";
> +                               regulator-min-microvolt = <3300000>;
> +                               regulator-max-microvolt = <3300000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vdd10_lcd: REG6 {
> +                               regulator-name = "VDD10_LCD";
> +                               regulator-min-microvolt = <1000000>;
> +                               regulator-max-microvolt = <1000000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcca_codec: REG7 {
> +                               regulator-name = "VCCA_CODEC";
> +                               regulator-min-microvolt = <3300000>;
> +                               regulator-max-microvolt = <3300000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcca_tp: REG8 {
> +                               regulator-name = "VCCA_TP";
> +                               regulator-min-microvolt = <3300000>;
> +                               regulator-max-microvolt = <3300000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vccio_pmu: REG9 {
> +                               regulator-name = "VCCIO_PMU";
> +                               regulator-min-microvolt = <3300000>;
> +                               regulator-max-microvolt = <3300000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vdd_10: REG10 {
> +                               regulator-name = "VDD_10";
> +                               regulator-min-microvolt = <1000000>;
> +                               regulator-max-microvolt = <1000000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcc_18: REG11 {
> +                               regulator-name = "VCC_18";
> +                               regulator-min-microvolt = <1800000>;
> +                               regulator-max-microvolt = <1800000>;
> +                               regulator-always-on;
> +                       };
> +
> +                       vcc18_lcd: REG12 {
> +                               regulator-name = "VCC18_LCD";
> +                               regulator-min-microvolt = <1800000>;
> +                               regulator-max-microvolt = <1800000>;
> +                               regulator-always-on;
> +                       };

Should all these regulators really need to be always-on?

Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Sjoerd Simons Sept. 14, 2015, 7:30 a.m. UTC | #4
On Mon, 2015-09-14 at 01:00 +0200, Javier Martinez Canillas wrote:
> Hello Sjoerd,
> 
> On Sat, Sep 12, 2015 at 12:36 AM, Sjoerd Simons
> <sjoerd.simons@collabora.co.uk> wrote:
> 
> [snip]
> 
> > +
> > +               regulators {
> > +                       vcc_ddr: REG1 {
> > +                               regulator-name = "VCC_DDR";
> > +                               regulator-min-microvolt =
> > <1200000>;
> > +                               regulator-max-microvolt =
> > <1200000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcc_io: REG2 {
> > +                               regulator-name = "VCC_IO";
> > +                               regulator-min-microvolt =
> > <3300000>;
> > +                               regulator-max-microvolt =
> > <3300000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vdd_log: REG3 {
> > +                               regulator-name = "VDD_LOG";
> > +                               regulator-min-microvolt =
> > <1000000>;
> > +                               regulator-max-microvolt =
> > <1000000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcc_20: REG4 {
> > +                               regulator-name = "VCC_20";
> > +                               regulator-min-microvolt =
> > <2000000>;
> > +                               regulator-max-microvolt =
> > <2000000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vccio_sd: REG5 {
> > +                               regulator-name = "VCCIO_SD";
> > +                               regulator-min-microvolt =
> > <3300000>;
> > +                               regulator-max-microvolt =
> > <3300000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vdd10_lcd: REG6 {
> > +                               regulator-name = "VDD10_LCD";
> > +                               regulator-min-microvolt =
> > <1000000>;
> > +                               regulator-max-microvolt =
> > <1000000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcca_codec: REG7 {
> > +                               regulator-name = "VCCA_CODEC";
> > +                               regulator-min-microvolt =
> > <3300000>;
> > +                               regulator-max-microvolt =
> > <3300000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcca_tp: REG8 {
> > +                               regulator-name = "VCCA_TP";
> > +                               regulator-min-microvolt =
> > <3300000>;
> > +                               regulator-max-microvolt =
> > <3300000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vccio_pmu: REG9 {
> > +                               regulator-name = "VCCIO_PMU";
> > +                               regulator-min-microvolt =
> > <3300000>;
> > +                               regulator-max-microvolt =
> > <3300000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vdd_10: REG10 {
> > +                               regulator-name = "VDD_10";
> > +                               regulator-min-microvolt =
> > <1000000>;
> > +                               regulator-max-microvolt =
> > <1000000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcc_18: REG11 {
> > +                               regulator-name = "VCC_18";
> > +                               regulator-min-microvolt =
> > <1800000>;
> > +                               regulator-max-microvolt =
> > <1800000>;
> > +                               regulator-always-on;
> > +                       };
> > +
> > +                       vcc18_lcd: REG12 {
> > +                               regulator-name = "VCC18_LCD";
> > +                               regulator-min-microvolt =
> > <1800000>;
> > +                               regulator-max-microvolt =
> > <1800000>;
> > +                               regulator-always-on;
> > +                       };
> 
> Should all these regulators really need to be always-on?

Ideally not all of them, turning the ones that aren't needed off is
definately on my list of things to do (together with the other
pheripherals, leds, hw. keys etc). 

For the first patch i do prefer to keep them on so we can have get some
more testing  with this board before fine-tuning those things (fwiw,
the rockchip evb board and others with essentially the same pmic setup
all also have them always-on)
Javier Martinez Canillas Sept. 14, 2015, 7:50 a.m. UTC | #5
Hello Sjoerd,

On Mon, Sep 14, 2015 at 9:30 AM, Sjoerd Simons
<sjoerd.simons@collabora.co.uk> wrote:

[snip]

>> > +
>> > +                       vcc18_lcd: REG12 {
>> > +                               regulator-name = "VCC18_LCD";
>> > +                               regulator-min-microvolt =
>> > <1800000>;
>> > +                               regulator-max-microvolt =
>> > <1800000>;
>> > +                               regulator-always-on;
>> > +                       };
>>
>> Should all these regulators really need to be always-on?
>
> Ideally not all of them, turning the ones that aren't needed off is
> definately on my list of things to do (together with the other
> pheripherals, leds, hw. keys etc).
>
> For the first patch i do prefer to keep them on so we can have get some
> more testing  with this board before fine-tuning those things (fwiw,

Ok.

> the rockchip evb board and others with essentially the same pmic setup
> all also have them always-on)

Yes but I believe that's because it was easier and there are
regulators on these boards that don't need to be always-on as well.

> --
> Sjoerd Simons
> Collabora Ltd.

Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Sjoerd Simons Sept. 14, 2015, 8:05 a.m. UTC | #6
Hey Javier,

On Mon, 2015-09-14 at 09:50 +0200, Javier Martinez Canillas wrote:
> Hello Sjoerd,
> 
> On Mon, Sep 14, 2015 at 9:30 AM, Sjoerd Simons
> <sjoerd.simons@collabora.co.uk> wrote:

> > For the first patch i do prefer to keep them on so we can have get
> > some
> > more testing  with this board before fine-tuning those things
> > (fwiw,
> 
> Ok.
> 
> > the rockchip evb board and others with essentially the same pmic
> > setup
> > all also have them always-on)
> 
> Yes but I believe that's because it was easier and there are
> regulators on these boards that don't need to be always-on as well.

Yes what i was trying to say is that it's not an uncommon to keep these
on for convenience while fine-tuning the device-tree setups ;)
Heiko Stuebner Sept. 14, 2015, 8:47 a.m. UTC | #7
Am Montag, 14. September 2015, 10:05:58 schrieb Sjoerd Simons:
> Hey Javier,
> 
> On Mon, 2015-09-14 at 09:50 +0200, Javier Martinez Canillas wrote:
> > Hello Sjoerd,
> > 
> > On Mon, Sep 14, 2015 at 9:30 AM, Sjoerd Simons
> > 
> > <sjoerd.simons@collabora.co.uk> wrote:
> > > For the first patch i do prefer to keep them on so we can have get
> > > some
> > > more testing  with this board before fine-tuning those things
> > > (fwiw,
> > 
> > Ok.
> > 
> > > the rockchip evb board and others with essentially the same pmic
> > > setup
> > > all also have them always-on)
> > 
> > Yes but I believe that's because it was easier and there are
> > regulators on these boards that don't need to be always-on as well.
> 
> Yes what i was trying to say is that it's not an uncommon to keep these
> on for convenience while fine-tuning the device-tree setups ;)

Also, a lot of drivers do not yet do proper regulator handling (our drm/kms 
driver as a prime example), so the number of regulators able to being actually 
turned off is quite slim.

So I guess I'm ok, with handling these once driver components can actually do 
something with their supplies :-) .


Heiko
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 233159d..1ed8ec1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -507,6 +507,7 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-firefly-beta.dtb \
 	rk3288-firefly.dtb \
 	rk3288-r89.dtb \
+	rk3288-rock2-square.dtb \
 	rk3288-veyron-jerry.dtb \
 	rk3288-veyron-minnie.dtb \
 	rk3288-veyron-pinky.dtb \
diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
new file mode 100644
index 0000000..01e69e8
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
@@ -0,0 +1,267 @@ 
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	phy-supply = <&vccio_pmu>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins &phy_rst>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+	rx_delay = <0x10>;
+	tx_delay = <0x30>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	act8846: act8846@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		inl1-supply = <&vcc_io>;
+		inl2-supply = <&vcc_sys>;
+		inl3-supply = <&vcc_20>;
+		vp1-supply = <&vcc_sys>;
+		vp2-supply = <&vcc_sys>;
+		vp3-supply = <&vcc_sys>;
+		vp4-supply = <&vcc_sys>;
+		status = "okay";
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "VCC_DDR";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "VCC_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "VDD_LOG";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "VCC_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "VCCIO_SD";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "VDD10_LCD";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcca_codec: REG7 {
+				regulator-name = "VCCA_CODEC";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcca_tp: REG8 {
+				regulator-name = "VCCA_TP";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vccio_pmu: REG9 {
+				regulator-name = "VCCIO_PMU";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "VDD_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_18: REG11 {
+				regulator-name = "VCC_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "VCC18_LCD";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-always-on;
+		regulator-enable-ramp-delay = <300>;
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-name = "vdd_gpu";
+		regulator-ramp-delay = <8000>;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&wdt {
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	gmac {
+		phy_rst: phy-rst {
+			rockchip,pins = <RK_GPIO4 8 RK_FUNC_GPIO  &pcfg_output_high>;
+		};
+	};
+};
+
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts b/arch/arm/boot/dts/rk3288-rock2-square.dts
new file mode 100644
index 0000000..42b72bb
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-rock2-square.dts
@@ -0,0 +1,164 @@ 
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3288-rock2-som.dtsi"
+
+/ {
+	model = "Radxa Rock 2 Square";
+	compatible = "rockchip,rk3288-rock2-square", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	vcc_usb_host: vcc-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		/* Always on as the rockchip usb phy doesn't have a vbus-supply
+		 * property */
+		regulator-always-on;
+		regulator-name = "vcc_host";
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;	/* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&gmac {
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <RK_GPIO0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <RK_GPIO7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};