deleted file mode 100644
@@ -1,173 +0,0 @@
-Marvell Xenon SDHCI Controller device tree bindings
-This file documents differences between the core mmc properties
-described by mmc.txt and the properties used by the Xenon implementation.
-
-Multiple SDHCs might be put into a single Xenon IP, to save size and cost.
-Each SDHC is independent and owns independent resources, such as register sets,
-clock and PHY.
-Each SDHC should have an independent device tree node.
-
-Required Properties:
-- compatible: should be one of the following
- - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SoC.
- Must provide a second register area and marvell,pad-type.
- - "marvell,armada-ap806-sdhci": For controllers on Armada AP806.
- - "marvell,armada-ap807-sdhci": For controllers on Armada AP807.
- - "marvell,armada-cp110-sdhci": For controllers on Armada CP110.
-
-- clocks:
- Array of clocks required for SDHC.
- Require at least input clock for Xenon IP core. For Armada AP806 and
- CP110, the AXI clock is also mandatory.
-
-- clock-names:
- Array of names corresponding to clocks property.
- The input clock for Xenon IP core should be named as "core".
- The input clock for the AXI bus must be named as "axi".
-
-- reg:
- * For "marvell,armada-3700-sdhci", two register areas.
- The first one for Xenon IP register. The second one for the Armada 3700 SoC
- PHY PAD Voltage Control register.
- Please follow the examples with compatible "marvell,armada-3700-sdhci"
- in below.
- Please also check property marvell,pad-type in below.
-
- * For other compatible strings, one register area for Xenon IP.
-
-Optional Properties:
-- marvell,xenon-sdhc-id:
- Indicate the corresponding bit index of current SDHC in
- SDHC System Operation Control Register Bit[7:0].
- Set/clear the corresponding bit to enable/disable current SDHC.
- If Xenon IP contains only one SDHC, this property is optional.
-
-- marvell,xenon-phy-type:
- Xenon support multiple types of PHYs.
- To select eMMC 5.1 PHY, set:
- marvell,xenon-phy-type = "emmc 5.1 phy"
- eMMC 5.1 PHY is the default choice if this property is not provided.
- To select eMMC 5.0 PHY, set:
- marvell,xenon-phy-type = "emmc 5.0 phy"
-
- All those types of PHYs can support eMMC, SD and SDIO.
- Please note that this property only presents the type of PHY.
- It doesn't stand for the entire SDHC type or property.
- For example, "emmc 5.1 phy" doesn't mean that this Xenon SDHC only
- supports eMMC 5.1.
-
-- marvell,xenon-phy-znr:
- Set PHY ZNR value.
- Only available for eMMC PHY.
- Valid range = [0:0x1F].
- ZNR is set as 0xF by default if this property is not provided.
-
-- marvell,xenon-phy-zpr:
- Set PHY ZPR value.
- Only available for eMMC PHY.
- Valid range = [0:0x1F].
- ZPR is set as 0xF by default if this property is not provided.
-
-- marvell,xenon-phy-nr-success-tun:
- Set the number of required consecutive successful sampling points
- used to identify a valid sampling window, in tuning process.
- Valid range = [1:7].
- Set as 0x4 by default if this property is not provided.
-
-- marvell,xenon-phy-tun-step-divider:
- Set the divider for calculating TUN_STEP.
- Set as 64 by default if this property is not provided.
-
-- marvell,xenon-phy-slow-mode:
- If this property is selected, transfers will bypass PHY.
- Only available when bus frequency lower than 55MHz in SDR mode.
- Disabled by default. Please only try this property if timing issues
- always occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25,
- SD Default Speed and HS mode and eMMC legacy speed mode.
-
-- marvell,xenon-tun-count:
- Xenon SDHC SoC usually doesn't provide re-tuning counter in
- Capabilities Register 3 Bit[11:8].
- This property provides the re-tuning counter.
- If this property is not set, default re-tuning counter will
- be set as 0x9 in driver.
-
-- marvell,pad-type:
- Type of Armada 3700 SoC PHY PAD Voltage Controller register.
- Only valid when "marvell,armada-3700-sdhci" is selected.
- Two types: "sd" and "fixed-1-8v".
- If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning and is
- switched to 1.8V when later in higher speed mode.
- If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for eMMC.
- Please follow the examples with compatible "marvell,armada-3700-sdhci"
- in below.
-
-Example:
-- For eMMC:
-
- sdhci@aa0000 {
- compatible = "marvell,armada-ap806-sdhci";
- reg = <0xaa0000 0x1000>;
- interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
- clocks = <&emmc_clk>,<&axi_clk>;
- clock-names = "core", "axi";
- bus-width = <4>;
- marvell,xenon-phy-slow-mode;
- marvell,xenon-tun-count = <11>;
- non-removable;
- no-sd;
- no-sdio;
-
- /* Vmmc and Vqmmc are both fixed */
- };
-
-- For SD/SDIO:
-
- sdhci@ab0000 {
- compatible = "marvell,armada-cp110-sdhci";
- reg = <0xab0000 0x1000>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
- vqmmc-supply = <&sd_vqmmc_regulator>;
- vmmc-supply = <&sd_vmmc_regulator>;
- clocks = <&sdclk>, <&axi_clk>;
- clock-names = "core", "axi";
- bus-width = <4>;
- marvell,xenon-tun-count = <9>;
- };
-
-- For eMMC with compatible "marvell,armada-3700-sdhci":
-
- sdhci@aa0000 {
- compatible = "marvell,armada-3700-sdhci";
- reg = <0xaa0000 0x1000>,
- <phy_addr 0x4>;
- interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
- clocks = <&emmcclk>;
- clock-names = "core";
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- non-removable;
- no-sd;
- no-sdio;
-
- /* Vmmc and Vqmmc are both fixed */
-
- marvell,pad-type = "fixed-1-8v";
- };
-
-- For SD/SDIO with compatible "marvell,armada-3700-sdhci":
-
- sdhci@ab0000 {
- compatible = "marvell,armada-3700-sdhci";
- reg = <0xab0000 0x1000>,
- <phy_addr 0x4>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
- vqmmc-supply = <&sd_regulator>;
- /* Vmmc is fixed */
- clocks = <&sdclk>;
- clock-names = "core";
- bus-width = <4>;
-
- marvell,pad-type = "sd";
- };
new file mode 100644
@@ -0,0 +1,252 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell Xenon SDHCI Controller device tree bindings
+
+description: |
+ This file documents differences between the core mmc properties described by
+ mmc-controller.yaml and the properties used by the Xenon implementation.
+
+ Multiple SDHCs might be put into a single Xenon IP, to save size and cost.
+ Each SDHC is independent and owns independent resources, such as register
+ sets, clock and PHY.
+
+ Each SDHC should have an independent device tree node.
+
+maintainers:
+ - Ulf Hansson <ulf.hansson@linaro.org>
+
+patternProperties:
+ "^sdhci@[0-9a-f]+$":
+ type: object
+ $ref: mmc-controller.yaml
+
+ properties:
+ compatible:
+ oneOf:
+ - const: marvell,armada-3700-sdhci
+ description: |
+ Must provide a second register area and marvell,pad-type
+ - const: marvell,armada-ap806-sdhci
+ - const: marvell,armada-ap807-sdhci
+ - const: marvell,armada-cp110-sdhci
+ - const: marvell,sdhci-xenon
+ - items:
+ - const: marvell,armada-3700-sdhci
+ - const: marvell,sdhci-xenon
+ - items:
+ - const: marvell,armada-ap807-sdhci
+ - const: marvell,armada-ap806-sdhci
+
+ reg:
+ minItems: 1
+ maxItems: 2
+ description: |
+ For "marvell,armada-3700-sdhci", two register areas. The first one
+ for Xenon IP register. The second one for the Armada 3700 SoC PHY PAD
+ Voltage Control register. Please follow the examples with compatible
+ "marvell,armada-3700-sdhci" in below.
+ Please also check property marvell,pad-type in below.
+
+ For other compatible strings, one register area for Xenon IP.
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: core
+ - const: axi
+
+ marvell,xenon-sdhc-id:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ description: |
+ Indicate the corresponding bit index of current SDHC in SDHC System
+ Operation Control Register Bit[7:0]. Set/clear the corresponding bit to
+ enable/disable current SDHC. If Xenon IP contains only one SDHC, this
+ property is optional.
+
+ marvell,xenon-phy-type:
+ enum:
+ - "emmc 5.1 phy"
+ - "emmc 5.0 phy"
+ description: |
+ Xenon support multiple types of PHYs. To select eMMC 5.1 PHY, set:
+ marvell,xenon-phy-type = "emmc 5.1 phy" eMMC 5.1 PHY is the default
+ choice if this property is not provided. To select eMMC 5.0 PHY, set:
+ marvell,xenon-phy-type = "emmc 5.0 phy"
+
+ All those types of PHYs can support eMMC, SD and SDIO. Please note that
+ this property only presents the type of PHY. It doesn't stand for the
+ entire SDHC type or property. For example, "emmc 5.1 phy" doesn't mean
+ that this Xenon SDHC only supports eMMC 5.1.
+
+ marvell,xenon-phy-znr:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0x1f
+ default: 0xf
+ description: |
+ Set PHY ZNR value.
+ Only available for eMMC PHY.
+ Valid range = [0:0x1F].
+ ZNR is set as 0xF by default if this property is not provided.
+
+ marvell,xenon-phy-zpr:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0x1f
+ default: 0xf
+ description: |
+ Set PHY ZPR value.
+ Only available for eMMC PHY.
+ Valid range = [0:0x1F].
+ ZPR is set as 0xF by default if this property is not provided.
+
+ marvell,xenon-phy-nr-success-tun:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+ default: 0x4
+ description: |
+ Set the number of required consecutive successful sampling points
+ used to identify a valid sampling window, in tuning process.
+ Valid range = [1:7].
+ Set as 0x4 by default if this property is not provided.
+
+ marvell,xenon-phy-tun-step-divider:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Set the divider for calculating TUN_STEP.
+ Set as 64 by default if this property is not provided.
+
+ marvell,xenon-phy-slow-mode:
+ type: boolean
+ description: |
+ If this property is selected, transfers will bypass PHY.
+ Only available when bus frequency lower than 55MHz in SDR mode.
+ Disabled by default. Please only try this property if timing issues
+ always occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25,
+ SD Default Speed and HS mode and eMMC legacy speed mode.
+
+ marvell,xenon-tun-count:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Xenon SDHC SoC usually doesn't provide re-tuning counter in
+ Capabilities Register 3 Bit[11:8].
+ This property provides the re-tuning counter.
+ If this property is not set, default re-tuning counter will
+ be set as 0x9 in driver.
+
+ marvell,pad-type:
+ enum:
+ - sd
+ - fixed-1-8v
+ description: |
+ Type of Armada 3700 SoC PHY PAD Voltage Controller register.
+ Only valid when "marvell,armada-3700-sdhci" is selected.
+ Two types: "sd" and "fixed-1-8v".
+ If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning and is
+ switched to 1.8V when later in higher speed mode.
+ If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for eMMC.
+ Please follow the examples with compatible "marvell,armada-3700-sdhci"
+ in below.
+
+ required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+
+ unevaluatedProperties: false
+
+additionalProperties: false
+
+examples:
+ - |
+ // For eMMC
+
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ sdhci@aa0000 {
+ compatible = "marvell,armada-ap807-sdhci", "marvell,armada-ap806-sdhci";
+ reg = <0xaa0000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&emmc_clk 0>, <&axi_clk 0>;
+ clock-names = "core", "axi";
+ bus-width = <4>;
+ marvell,xenon-phy-slow-mode;
+ marvell,xenon-tun-count = <11>;
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ /* Vmmc and Vqmmc are both fixed */
+ };
+
+ - |
+ // For SD/SDIO
+
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ sdhci@ab0000 {
+ compatible = "marvell,armada-cp110-sdhci";
+ reg = <0xab0000 0x1000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ vqmmc-supply = <&sd_vqmmc_regulator>;
+ vmmc-supply = <&sd_vmmc_regulator>;
+ clocks = <&sdclk 0>, <&axi_clk 0>;
+ clock-names = "core", "axi";
+ bus-width = <4>;
+ marvell,xenon-tun-count = <9>;
+ };
+
+ - |
+ // For eMMC with compatible "marvell,armada-3700-sdhci":
+
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ sdhci@aa0000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xaa0000 0x1000>,
+ <0x17808 0x4>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&emmcclk 0>;
+ clock-names = "core";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ non-removable;
+ no-sd;
+ no-sdio;
+
+ /* Vmmc and Vqmmc are both fixed */
+
+ marvell,pad-type = "fixed-1-8v";
+ };
+
+ - |
+ // For SD/SDIO with compatible "marvell,armada-3700-sdhci":
+
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ sdhci@ab0000 {
+ compatible = "marvell,armada-3700-sdhci";
+ reg = <0xab0000 0x1000>,
+ <0x17808 0x4>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ vqmmc-supply = <&sd_regulator>;
+ /* Vmmc is fixed */
+ clocks = <&sdclk 0>;
+ clock-names = "core";
+ bus-width = <4>;
+
+ marvell,pad-type = "sd";
+ };
Convert the marvell,xenon-sdhci binding to JSON schema. This is a fairly direct conversion so there are some requirements that are documented in prose but not currently enforced. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> --- .../bindings/mmc/marvell,xenon-sdhci.txt | 173 ------------ .../bindings/mmc/marvell,xenon-sdhci.yaml | 252 ++++++++++++++++++ 2 files changed, 252 insertions(+), 173 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.yaml