@@ -773,7 +773,7 @@ &pm8916_gpios {
"USB_HUB_RESET_N_PM",
"USB_SW_SEL_PM";
- usb_hub_reset_pm: usb-hub-reset-pm {
+ usb_hub_reset_pm: usb-hub-reset-pm-state {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -781,14 +781,14 @@ usb_hub_reset_pm: usb-hub-reset-pm {
output-high;
};
- usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+ usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
};
- usb_sw_sel_pm: usb-sw-sel-pm {
+ usb_sw_sel_pm: usb-sw-sel-pm-state {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -797,7 +797,7 @@ usb_sw_sel_pm: usb-sw-sel-pm {
output-high;
};
- usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+ usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -806,7 +806,7 @@ usb_sw_sel_pm_device: usb-sw-sel-pm-device {
output-low;
};
- pm8916_gpios_leds: pm8916-gpios-leds {
+ pm8916_gpios_leds: pm8916-gpios-leds-state {
pins = "gpio1", "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -555,7 +555,7 @@ &pm8994_gpios {
pinctrl-names = "default";
pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
- ls_exp_gpio_f: pm8994_gpio5 {
+ ls_exp_gpio_f: pm8994-gpio5-state {
pinconf {
pins = "gpio5";
output-low;
@@ -563,7 +563,7 @@ pinconf {
};
};
- bt_en_gpios: bt_en_gpios {
+ bt_en_gpios: bt-en-pios-state {
pinconf {
pins = "gpio19";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -574,7 +574,7 @@ pinconf {
};
};
- wlan_en_gpios: wlan_en_gpios {
+ wlan_en_gpios: wlan-en-gpios-state {
pinconf {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -585,7 +585,7 @@ pinconf {
};
};
- audio_mclk: clk_div1 {
+ audio_mclk: clk-div1-state {
pinconf {
pins = "gpio15";
function = "func1";
@@ -593,7 +593,7 @@ pinconf {
};
};
- volume_up_gpio: pm8996_gpio2 {
+ volume_up_gpio: pm8996-gpio2-state {
pinconf {
pins = "gpio2";
function = "normal";
@@ -605,7 +605,7 @@ pinconf {
};
};
- divclk4_pin_a: divclk4 {
+ divclk4_pin_a: divclk4-state {
pinconf {
pins = "gpio18";
function = PMIC_GPIO_FUNC_FUNC2;
@@ -615,7 +615,7 @@ pinconf {
};
};
- usb3_vbus_det_gpio: pm8996_gpio22 {
+ usb3_vbus_det_gpio: pm8996-gpio22-state {
pinconf {
pins = "gpio22";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -671,7 +671,7 @@ &pmi8994_gpios {
"NC",
"NC";
- usb2_vbus_det_gpio: pmi8996_gpio6 {
+ usb2_vbus_det_gpio: pmi8996-gpio6-state {
pinconf {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -463,7 +463,7 @@ tsp_en_default: tsp-en-default {
};
&pm8916_gpios {
- nfc_clk_req: nfc-clk-req {
+ nfc_clk_req: nfc-clk-req-state {
pins = "gpio2";
function = "func1";
@@ -470,7 +470,7 @@ qca6174_bt: bluetooth {
};
&pm8994_gpios {
- bt_en_gpios: bt_en_gpios {
+ bt_en_gpios: bt-en-gpios-state {
pinconf {
pins = "gpio19";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -481,7 +481,7 @@ pinconf {
};
};
- divclk4_pin_a: divclk4 {
+ divclk4_pin_a: divclk4-state {
pinconf {
pins = "gpio18";
function = PMIC_GPIO_FUNC_FUNC2;
@@ -519,19 +519,19 @@ &pmi8994_gpios {
* TODO: remove once a driver is available
* TODO: add VBUS GPIO 5
*/
- hd3ss460_pol: pol_low {
+ hd3ss460_pol: pol-low-state {
pins = "gpio8";
drive-strength = <3>;
bias-pull-down;
};
- hd3ss460_amsel: amsel_high {
+ hd3ss460_amsel: amsel-high-state {
pins = "gpio9";
drive-strength = <1>;
bias-pull-up;
};
- hd3ss460_en: en_high {
+ hd3ss460_en: en-high-state {
pins = "gpio10";
drive-strength = <1>;
bias-pull-up;
@@ -247,14 +247,14 @@ &pm8994_gpios {
* probably a reason for it, and just to be on the safe side, we follow suit.
*/
pm8994_gpios_defaults: pm8994-gpios-default-state {
- pm8994-gpio1-nc {
+ pm8994-gpio1-nc-pins {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
bias-high-impedance;
};
- vol-down-n {
+ vol-down-n-pins {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -264,7 +264,7 @@ vol-down-n {
power-source = <PM8994_GPIO_S4>;
};
- vol-up-n {
+ vol-up-n-pins {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -273,7 +273,7 @@ vol-up-n {
power-source = <PM8994_GPIO_S4>;
};
- camera-snapshot-n {
+ camera-snapshot-n-pins {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -283,7 +283,7 @@ camera-snapshot-n {
power-source = <PM8994_GPIO_S4>;
};
- camera-focus-n {
+ camera-focus-n-pins {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -293,7 +293,7 @@ camera-focus-n {
power-source = <PM8994_GPIO_S4>;
};
- pm8994-gpio6-nc {
+ pm8994-gpio6-nc-pins {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -301,7 +301,7 @@ pm8994-gpio6-nc {
power-source = <PM8994_GPIO_VPH>;
};
- nfc-download {
+ nfc-download-pins {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
@@ -311,7 +311,7 @@ nfc-download {
power-source = <PM8994_GPIO_S4>;
};
- pm8994-gpio8-nc {
+ pm8994-gpio8-nc-pins {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
@@ -321,7 +321,7 @@ pm8994-gpio8-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pm8994-gpio9-nc {
+ pm8994-gpio9-nc-pins {
pins = "gpio9";
function = PMIC_GPIO_FUNC_NORMAL;
output-high;
@@ -331,7 +331,7 @@ pm8994-gpio9-nc {
power-source = <PM8994_GPIO_VPH>;
};
- nfc-clock {
+ nfc-clock-pins {
pins = "gpio10";
function = PMIC_GPIO_FUNC_NORMAL;
input-enable;
@@ -341,7 +341,7 @@ nfc-clock {
power-source = <PM8994_GPIO_S4>;
};
- pm8994-gpio11-nc {
+ pm8994-gpio11-nc-pins {
pins = "gpio11";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -349,7 +349,7 @@ pm8994-gpio11-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pm8994-gpio12-nc {
+ pm8994-gpio12-nc-pins {
pins = "gpio12";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -357,7 +357,7 @@ pm8994-gpio12-nc {
power-source = <PM8994_GPIO_VPH>;
};
- ear-enable {
+ ear-enable-pins {
pins = "gpio13";
function = PMIC_GPIO_FUNC_NORMAL;
output-high;
@@ -367,7 +367,7 @@ ear-enable {
power-source = <PM8994_GPIO_S4>;
};
- pm8994-gpio14-nc {
+ pm8994-gpio14-nc-pins {
pins = "gpio14";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -377,7 +377,7 @@ pm8994-gpio14-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pm-divclk1-gpio {
+ pm-divclk1-gpio-pins {
pins = "gpio15";
function = "func1";
output-high;
@@ -387,13 +387,13 @@ pm-divclk1-gpio {
power-source = <PM8994_GPIO_VPH>;
};
- pmi-clk-gpio {
+ pmi-clk-gpio-pins {
pins = "gpio16";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
};
- pm8994-gpio17-nc {
+ pm8994-gpio17-nc-pins {
pins = "gpio17";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -401,7 +401,7 @@ pm8994-gpio17-nc {
power-source = <PM8994_GPIO_VPH>;
};
- rome-sleep {
+ rome-sleep-pins {
pins = "gpio18";
function = PMIC_GPIO_FUNC_FUNC2;
output-low;
@@ -411,7 +411,7 @@ rome-sleep {
power-source = <PM8994_GPIO_S4>;
};
- pm8994-gpio19-nc {
+ pm8994-gpio19-nc-pins {
pins = "gpio19";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
@@ -421,7 +421,7 @@ pm8994-gpio19-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pm8994-gpio22-nc {
+ pm8994-gpio22-nc-pins {
pins = "gpio22";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -446,34 +446,34 @@ &pm8994_mpps {
"RF_ID";
pm8994_mpps_defaults: pm8994-mpps-default-state {
- lcd-id_adc-mpp {
+ lcd-id_adc-mpp-pins {
pins = "mpp2";
function = "analog";
input-enable;
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>;
};
- pm-mpp4-nc {
+ pm-mpp4-nc-pins {
pins = "mpp4";
function = "digital";
bias-high-impedance;
power-source = <PM8994_GPIO_VPH>;
};
- flash-therm-mpp {
+ flash-therm-mpp-pins {
pins = "mpp5";
function = "analog";
input-enable;
qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
};
- mpp6-nc {
+ mpp6-nc-pins {
pins = "mpp6";
function = "digital";
bias-high-impedance;
};
- rf-id-mpp {
+ rf-id-mpp-pins {
pins = "mpp8";
function = "analog";
input-enable;
@@ -504,7 +504,7 @@ &pmi8994_gpios {
"NC";
pmi8994_gpios_defaults: pmi8994-gpios-default-state {
- vib-ldo-en-gpio {
+ vib-ldo-en-gpio-pins {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -513,7 +513,7 @@ vib-ldo-en-gpio {
power-source = <PM8994_GPIO_S4>;
};
- pmi-gpio2-nc {
+ pmi-gpio2-nc-pins {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -523,7 +523,7 @@ pmi-gpio2-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pmi-gpio3-nc {
+ pmi-gpio3-nc-pins {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -533,7 +533,7 @@ pmi-gpio3-nc {
power-source = <PM8994_GPIO_VPH>;
};
- pmi-gpio4-nc {
+ pmi-gpio4-nc-pins {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -542,7 +542,7 @@ pmi-gpio4-nc {
power-source = <PM8994_GPIO_S4>;
};
- pmi-gpio5-nc {
+ pmi-gpio5-nc-pins {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -551,7 +551,7 @@ pmi-gpio5-nc {
power-source = <PM8994_GPIO_S4>;
};
- pmi-gpio6-nc {
+ pmi-gpio6-nc-pins {
pins = "gpio6";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -560,7 +560,7 @@ pmi-gpio6-nc {
power-source = <PM8994_GPIO_S4>;
};
- pmi-gpio7-nc {
+ pmi-gpio7-nc-pins {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -569,7 +569,7 @@ pmi-gpio7-nc {
power-source = <PM8994_GPIO_S4>;
};
- pmi-gpio8-nc {
+ pmi-gpio8-nc-pins {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
@@ -578,13 +578,13 @@ pmi-gpio8-nc {
power-source = <PM8994_GPIO_S4>;
};
- usb-switch-sel {
+ usb-switch-sel-pins {
pins = "gpio9";
function = PMIC_GPIO_FUNC_NORMAL;
drive-push-pull;
};
- pmi-gpio10-nc {
+ pmi-gpio10-nc-pins {
pins = "gpio10";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
@@ -608,7 +608,7 @@ vdd_gfx: s2 {
};
&pm8994_gpios {
- wlan_en_default: wlan-en-default {
+ wlan_en_default: wlan-en-state {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
@@ -617,7 +617,7 @@ wlan_en_default: wlan-en-default {
bias-disable;
};
- rome_enable_default: rome-enable-default {
+ rome_enable_default: rome-enable-state {
pins = "gpio9";
function = PMIC_GPIO_FUNC_NORMAL;
output-high;
@@ -625,7 +625,7 @@ rome_enable_default: rome-enable-default {
power-source = <PM8994_GPIO_VPH>;
};
- divclk1_default: divclk1_default {
+ divclk1_default: divclk1-state {
pins = "gpio15";
function = PMIC_GPIO_FUNC_FUNC1;
bias-disable;
@@ -633,7 +633,7 @@ divclk1_default: divclk1_default {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
};
- divclk4_pin_a: divclk4 {
+ divclk4_pin_a: divclk4-state {
pins = "gpio18";
function = PMIC_GPIO_FUNC_FUNC2;
bias-disable;
@@ -257,7 +257,7 @@ &pm8994_gpios {
"UIM_BATT_ALARM", /* GPIO_21 */
"NC"; /* GPIO_22 */
- divclk2_pin_a: divclk2 {
+ divclk2_pin_a: divclk2-state {
pins = "gpio16";
function = PMIC_GPIO_FUNC_FUNC2;
bias-disable;
@@ -214,7 +214,7 @@ &mmss_smmu {
};
&pm8998_gpio {
- vol_up_pin_a: vol-up-active {
+ vol_up_pin_a: vol-up-active-state {
pins = "gpio6";
function = "normal";
bias-pull-up;
@@ -222,7 +222,7 @@ vol_up_pin_a: vol-up-active {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_focus_pin_a: cam-focus-btn-active {
+ cam_focus_pin_a: cam-focus-btn-active-state {
pins = "gpio7";
function = "normal";
bias-pull-up;
@@ -230,7 +230,7 @@ cam_focus_pin_a: cam-focus-btn-active {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_snapshot_pin_a: cam-snapshot-btn-active {
+ cam_snapshot_pin_a: cam-snapshot-btn-active-state {
pins = "gpio8";
function = "normal";
bias-pull-up;
@@ -32,7 +32,7 @@ button-backlight {
};
&pmi8998_gpio {
- button_backlight_default: button-backlight-default {
+ button_backlight_default: button-backlight-state {
pinconf {
pins = "gpio5";
function = "normal";
@@ -263,7 +263,7 @@ pm8005_s1: s1 { /* VDD_GFX supply */
};
&pm8998_gpio {
- vol_keys_default: vol-keys-default {
+ vol_keys_default: vol-keys-state {
pinconf {
pins = "gpio5", "gpio6";
function = "normal";
@@ -38,7 +38,7 @@ &lab {
};
&pmi8998_gpio {
- disp_dvdd_en: disp-dvdd-en-active {
+ disp_dvdd_en: disp-dvdd-en-active-state {
pins = "gpio10";
function = "normal";
bias-disable;
@@ -295,7 +295,7 @@ pm8005_s1: s1 {
};
&pm8998_gpio {
- vol_down_pin_a: vol-down-active {
+ vol_down_pin_a: vol-down-active-state {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -303,7 +303,7 @@ vol_down_pin_a: vol-down-active {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_focus_pin_a: cam-focus-btn-active {
+ cam_focus_pin_a: cam-focus-btn-active-state {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -311,7 +311,7 @@ cam_focus_pin_a: cam-focus-btn-active {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_snapshot_pin_a: cam-snapshot-btn-active {
+ cam_snapshot_pin_a: cam-snapshot-btn-active-state {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -319,7 +319,7 @@ cam_snapshot_pin_a: cam-snapshot-btn-active {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- audio_mclk_pin: audio-mclk-pin-active {
+ audio_mclk_pin: audio-mclk-pin-active-state {
pins = "gpio13";
function = "func2";
power-source = <0>;
@@ -327,7 +327,7 @@ audio_mclk_pin: audio-mclk-pin-active {
};
&pmi8998_gpio {
- cam_vio_default: cam-vio-active {
+ cam_vio_default: cam-vio-active-state {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
bias-disable;
@@ -337,7 +337,7 @@ cam_vio_default: cam-vio-active {
power-source = <1>;
};
- vib_default: vib-en {
+ vib_default: vib-en-state {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
bias-disable;
@@ -304,7 +304,7 @@ pinconf {
};
&pms405_gpios {
- usb_vbus_boost_pin: usb-vbus-boost-pin {
+ usb_vbus_boost_pin: usb-vbus-boost-state {
pinconf {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -312,7 +312,7 @@ pinconf {
power-source = <1>;
};
};
- usb3_vbus_pin: usb3-vbus-pin {
+ usb3_vbus_pin: usb3-vbus-state {
pinconf {
pins = "gpio12";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -796,7 +796,7 @@ &pm8150l_gpios {
"NC",
"PM3003A_MODE";
- lt9611_rst_pin: lt9611-rst-pin {
+ lt9611_rst_pin: lt9611-rst-state {
pins = "gpio5";
function = "normal";
@@ -467,7 +467,7 @@ wifi-firmware {
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
&pm6150l_gpio {
- disp_pins: disp-pins {
+ disp_pins: disp-state {
pinconf {
pins = "gpio3";
function = PMIC_GPIO_FUNC_FUNC1;
@@ -368,7 +368,7 @@ &dp_hot_plug_det {
};
&pm7325_gpios {
- key_vol_up_default: key-vol-up-default {
+ key_vol_up_default: key-vol-up-state {
pins = "gpio6";
function = "normal";
input-enable;
@@ -457,7 +457,7 @@ &sdc1_rclk {
*/
&pm8350c_gpios {
- pmic_edp_bl_en: pmic-edp-bl-en {
+ pmic_edp_bl_en: pmic-edp-bl-en-state {
pins = "gpio7";
function = "normal";
bias-disable;
@@ -467,7 +467,7 @@ pmic_edp_bl_en: pmic-edp-bl-en {
output-low;
};
- pmic_edp_bl_pwm: pmic-edp-bl-pwm {
+ pmic_edp_bl_pwm: pmic-edp-bl-pwm-state {
pins = "gpio8";
function = "func1";
bias-disable;
@@ -569,7 +569,7 @@ &pm8998_gpio {
"OPTION2",
"PM845_SLB";
- cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en {
+ cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en-state {
pins = "gpio12";
function = "normal";
@@ -578,7 +578,7 @@ cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
};
- cam0_avdd_2v8_en_default: cam0-avdd-2v8-en {
+ cam0_avdd_2v8_en_default: cam0-avdd-2v8-en-state {
pins = "gpio10";
function = "normal";
@@ -587,7 +587,7 @@ cam0_avdd_2v8_en_default: cam0-avdd-2v8-en {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
};
- vol_up_pin_a: vol-up-active {
+ vol_up_pin_a: vol-up-active-state {
pins = "gpio6";
function = "normal";
input-enable;
@@ -440,7 +440,7 @@ &mss_pil {
};
&pm8998_gpio {
- volume_down_gpio: pm8998_gpio5 {
+ volume_down_gpio: pm8998-gpio5-state {
pinconf {
pins = "gpio5";
function = "normal";
@@ -450,7 +450,7 @@ pinconf {
};
};
- volume_up_gpio: pm8998_gpio6 {
+ volume_up_gpio: pm8998-gpio6-state {
pinconf {
pins = "gpio6";
function = "normal";
@@ -508,7 +508,7 @@ &mss_pil {
};
&pm8998_gpio {
- volume_up_gpio: pm8998_gpio6 {
+ volume_up_gpio: pm8998-gpio6-state {
pinconf {
pins = "gpio6";
function = "normal";
@@ -306,7 +306,7 @@ &ipa {
};
&pm8998_gpio {
- vol_up_pin_a: vol-up-active {
+ vol_up_pin_a: vol-up-active-state {
pins = "gpio6";
function = "normal";
input-enable;
@@ -339,7 +339,7 @@ &pm6150l_wled {
};
&pm6350_gpios {
- gpio_keys_pin: gpio-keys-pin {
+ gpio_keys_pin: gpio-keys-state {
pins = "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
DT schema expects PMIC GPIO pin configuration nodes to be named with '-state' suffix. Optional children should be either 'pinconf' or followed with '-pins' suffix. This fixes dtbs_check warnings like: sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- arch/arm64/boot/dts/qcom/apq8016-sbc.dts | 10 +-- arch/arm64/boot/dts/qcom/apq8096-db820c.dts | 16 ++--- .../qcom/msm8916-samsung-a2015-common.dtsi | 2 +- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 10 +-- .../dts/qcom/msm8996-sony-xperia-tone.dtsi | 70 +++++++++---------- .../boot/dts/qcom/msm8996-xiaomi-common.dtsi | 8 +-- .../boot/dts/qcom/msm8996-xiaomi-gemini.dts | 2 +- .../boot/dts/qcom/msm8998-fxtec-pro1.dts | 6 +- .../dts/qcom/msm8998-oneplus-cheeseburger.dts | 2 +- .../boot/dts/qcom/msm8998-oneplus-common.dtsi | 2 +- .../msm8998-sony-xperia-yoshino-maple.dts | 2 +- .../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 12 ++-- arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 4 +- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 2 +- arch/arm64/boot/dts/qcom/sc7180-idp.dts | 2 +- arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 2 +- arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi | 4 +- arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 6 +- .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 4 +- .../boot/dts/qcom/sdm845-shift-axolotl.dts | 2 +- .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 2 +- .../boot/dts/qcom/sm7225-fairphone-fp4.dts | 2 +- 22 files changed, 86 insertions(+), 86 deletions(-)