diff mbox series

[v2] spi: spi-ti-qspi: Support per-transfer and per-slave speed_hz settings

Message ID 20220519.084604.966119051165023533.atsushi.nemoto@sord.co.jp
State Accepted
Commit 8d0b512844fdee83b6299647aa178828a4ebfc3b
Headers show
Series [v2] spi: spi-ti-qspi: Support per-transfer and per-slave speed_hz settings | expand

Commit Message

Atsushi Nemoto May 18, 2022, 11:46 p.m. UTC 
The spi-ti-qspi driver initializes its spi clock by the
spi-max-frequency property from the controller node, and ignores
per-transfer (and per-slave) speed_hz settings.

Isolate clock settings out from ti_qspi_setup() and call it from
ti_qspi_start_transfer_one() and ti_qspi_exec_mem_op(), using
per-transfer speed_hz and per-slave max_speed_hz settings.

Also drop spi_max_frequency from struct ti_qspi and use spi_master's
max_speed_hz.

Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
---
Changes from v1:
 - rebase against broonie/spi.git for-next branch
 - use pm_runtime_resume_and_get instead of pm_runtime_get_sync

 drivers/spi/spi-ti-qspi.c | 75 ++++++++++++++++++++-------------------
 1 file changed, 39 insertions(+), 36 deletions(-)

Comments

Mark Brown June 7, 2022, 10:46 a.m. UTC | #1 
On Thu, 19 May 2022 08:46:04 +0900 (JST), Atsushi Nemoto wrote:
> The spi-ti-qspi driver initializes its spi clock by the
> spi-max-frequency property from the controller node, and ignores
> per-transfer (and per-slave) speed_hz settings.
> 
> Isolate clock settings out from ti_qspi_setup() and call it from
> ti_qspi_start_transfer_one() and ti_qspi_exec_mem_op(), using
> per-transfer speed_hz and per-slave max_speed_hz settings.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/1] spi: spi-ti-qspi: Support per-transfer and per-slave speed_hz settings
      commit: 8d0b512844fdee83b6299647aa178828a4ebfc3b

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark
diff mbox series

Patch

diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index b5b65d882d7a..60086869bcae 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -57,7 +57,6 @@  struct ti_qspi {
 	void			*rx_bb_addr;
 	struct dma_chan		*rx_chan;
 
-	u32 spi_max_frequency;
 	u32 cmd;
 	u32 dc;
 
@@ -140,37 +139,19 @@  static inline void ti_qspi_write(struct ti_qspi *qspi,
 static int ti_qspi_setup(struct spi_device *spi)
 {
 	struct ti_qspi	*qspi = spi_master_get_devdata(spi->master);
-	struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
-	int clk_div = 0, ret;
-	u32 clk_ctrl_reg, clk_rate, clk_mask;
+	int ret;
 
 	if (spi->master->busy) {
 		dev_dbg(qspi->dev, "master busy doing other transfers\n");
 		return -EBUSY;
 	}
 
-	if (!qspi->spi_max_frequency) {
+	if (!qspi->master->max_speed_hz) {
 		dev_err(qspi->dev, "spi max frequency not defined\n");
 		return -EINVAL;
 	}
 
-	clk_rate = clk_get_rate(qspi->fclk);
-
-	clk_div = DIV_ROUND_UP(clk_rate, qspi->spi_max_frequency) - 1;
-
-	if (clk_div < 0) {
-		dev_dbg(qspi->dev, "clock divider < 0, using /1 divider\n");
-		return -EINVAL;
-	}
-
-	if (clk_div > QSPI_CLK_DIV_MAX) {
-		dev_dbg(qspi->dev, "clock divider >%d , using /%d divider\n",
-				QSPI_CLK_DIV_MAX, QSPI_CLK_DIV_MAX + 1);
-		return -EINVAL;
-	}
-
-	dev_dbg(qspi->dev, "hz: %d, clock divider %d\n",
-			qspi->spi_max_frequency, clk_div);
+	spi->max_speed_hz = min(spi->max_speed_hz, qspi->master->max_speed_hz);
 
 	ret = pm_runtime_resume_and_get(qspi->dev);
 	if (ret < 0) {
@@ -178,18 +159,6 @@  static int ti_qspi_setup(struct spi_device *spi)
 		return ret;
 	}
 
-	clk_ctrl_reg = ti_qspi_read(qspi, QSPI_SPI_CLOCK_CNTRL_REG);
-
-	clk_ctrl_reg &= ~QSPI_CLK_EN;
-
-	/* disable SCLK */
-	ti_qspi_write(qspi, clk_ctrl_reg, QSPI_SPI_CLOCK_CNTRL_REG);
-
-	/* enable SCLK */
-	clk_mask = QSPI_CLK_EN | clk_div;
-	ti_qspi_write(qspi, clk_mask, QSPI_SPI_CLOCK_CNTRL_REG);
-	ctx_reg->clkctrl = clk_mask;
-
 	pm_runtime_mark_last_busy(qspi->dev);
 	ret = pm_runtime_put_autosuspend(qspi->dev);
 	if (ret < 0) {
@@ -200,6 +169,37 @@  static int ti_qspi_setup(struct spi_device *spi)
 	return 0;
 }
 
+static void ti_qspi_setup_clk(struct ti_qspi *qspi, u32 speed_hz)
+{
+	struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
+	int clk_div;
+	u32 clk_ctrl_reg, clk_rate, clk_ctrl_new;
+
+	clk_rate = clk_get_rate(qspi->fclk);
+	clk_div = DIV_ROUND_UP(clk_rate, speed_hz) - 1;
+	clk_div = clamp(clk_div, 0, QSPI_CLK_DIV_MAX);
+	dev_dbg(qspi->dev, "hz: %d, clock divider %d\n", speed_hz, clk_div);
+
+	pm_runtime_resume_and_get(qspi->dev);
+
+	clk_ctrl_new = QSPI_CLK_EN | clk_div;
+	if (ctx_reg->clkctrl != clk_ctrl_new) {
+		clk_ctrl_reg = ti_qspi_read(qspi, QSPI_SPI_CLOCK_CNTRL_REG);
+
+		clk_ctrl_reg &= ~QSPI_CLK_EN;
+
+		/* disable SCLK */
+		ti_qspi_write(qspi, clk_ctrl_reg, QSPI_SPI_CLOCK_CNTRL_REG);
+
+		/* enable SCLK */
+		ti_qspi_write(qspi, clk_ctrl_new, QSPI_SPI_CLOCK_CNTRL_REG);
+		ctx_reg->clkctrl = clk_ctrl_new;
+	}
+
+	pm_runtime_mark_last_busy(qspi->dev);
+	pm_runtime_put_autosuspend(qspi->dev);
+}
+
 static void ti_qspi_restore_ctx(struct ti_qspi *qspi)
 {
 	struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
@@ -623,8 +623,10 @@  static int ti_qspi_exec_mem_op(struct spi_mem *mem,
 
 	mutex_lock(&qspi->list_lock);
 
-	if (!qspi->mmap_enabled || qspi->current_cs != mem->spi->chip_select)
+	if (!qspi->mmap_enabled || qspi->current_cs != mem->spi->chip_select) {
+		ti_qspi_setup_clk(qspi, mem->spi->max_speed_hz);
 		ti_qspi_enable_memory_map(mem->spi);
+	}
 	ti_qspi_setup_mmap_read(mem->spi, op->cmd.opcode, op->data.buswidth,
 				op->addr.nbytes, op->dummy.nbytes);
 
@@ -701,6 +703,7 @@  static int ti_qspi_start_transfer_one(struct spi_master *master,
 		wlen = t->bits_per_word >> 3;
 		transfer_len_words = min(t->len / wlen, frame_len_words);
 
+		ti_qspi_setup_clk(qspi, t->speed_hz);
 		ret = qspi_transfer_msg(qspi, t, transfer_len_words * wlen);
 		if (ret) {
 			dev_dbg(qspi->dev, "transfer message failed\n");
@@ -851,7 +854,7 @@  static int ti_qspi_probe(struct platform_device *pdev)
 	pm_runtime_enable(&pdev->dev);
 
 	if (!of_property_read_u32(np, "spi-max-frequency", &max_freq))
-		qspi->spi_max_frequency = max_freq;
+		master->max_speed_hz = max_freq;
 
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);