@@ -23,6 +23,15 @@
#define REG_TYPE 0x4
#define REG_SUBTYPE 0x5
+/* GPIO peripheral type and subtype out_values */
+#define REG_TYPE_VAL 0x10
+#define REG_SUBTYPE_GPIO_4CH 0x1
+#define REG_SUBTYPE_GPIOC_4CH 0x5
+#define REG_SUBTYPE_GPIO_8CH 0x9
+#define REG_SUBTYPE_GPIOC_8CH 0xd
+#define REG_SUBTYPE_GPIO_LV 0x10
+#define REG_SUBTYPE_GPIO_MV 0x11
+
#define REG_STATUS 0x08
#define REG_STATUS_VAL_MASK 0x1
@@ -33,6 +42,10 @@
#define REG_CTL_MODE_INOUT 0x20
#define REG_CTL_MODE_OUTPUT 0x10
#define REG_CTL_OUTPUT_MASK 0x0F
+#define REG_CTL_LV_MV_MODE_MASK 0x3
+#define REG_CTL_LV_MV_MODE_INPUT 0x0
+#define REG_CTL_LV_MV_MODE_INOUT 0x2
+#define REG_CTL_LV_MV_MODE_OUTPUT 0x1
#define REG_DIG_VIN_CTL 0x41
#define REG_DIG_VIN_VIN0 0
@@ -40,6 +53,10 @@
#define REG_DIG_PULL_CTL 0x42
#define REG_DIG_PULL_NO_PU 0x5
+#define REG_LV_MV_OUTPUT_CTL 0x44
+#define REG_LV_MV_OUTPUT_CTL_MASK 0x80
+#define REG_LV_MV_OUTPUT_CTL_SHIFT 7
+
#define REG_DIG_OUT_CTL 0x45
#define REG_DIG_OUT_CTL_CMOS (0x0 << 4)
#define REG_DIG_OUT_CTL_DRIVE_L 0x1
@@ -49,6 +66,7 @@
struct qcom_gpio_bank {
uint32_t pid; /* Peripheral ID on SPMI bus */
+ bool lv_mv_type; /* If subtype is GPIO_LV(0x10) or GPIO_MV(0x11) */
};
static int qcom_gpio_set_direction(struct udevice *dev, unsigned offset,
@@ -56,6 +74,7 @@ static int qcom_gpio_set_direction(struct udevice *dev, unsigned offset,
{
struct qcom_gpio_bank *priv = dev_get_priv(dev);
uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+ uint32_t reg_ctl_val;
int ret;
/* Disable the GPIO */
@@ -64,16 +83,31 @@ static int qcom_gpio_set_direction(struct udevice *dev, unsigned offset,
if (ret < 0)
return ret;
- /* Select the mode */
- if (input)
- ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
- REG_CTL_MODE_INPUT);
- else
- ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
- REG_CTL_MODE_INOUT | (value ? 1 : 0));
+ /* Select the mode and output */
+ if (priv->lv_mv_type) {
+ if (input)
+ reg_ctl_val = REG_CTL_LV_MV_MODE_INPUT;
+ else
+ reg_ctl_val = REG_CTL_LV_MV_MODE_INOUT;
+ } else {
+ if (input)
+ reg_ctl_val = REG_CTL_MODE_INPUT;
+ else
+ reg_ctl_val = REG_CTL_MODE_INOUT | !!value;
+ }
+
+ ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL, reg_ctl_val);
if (ret < 0)
return ret;
+ if (priv->lv_mv_type && !input) {
+ ret = pmic_reg_write(dev->parent,
+ gpio_base + REG_LV_MV_OUTPUT_CTL,
+ !!value << REG_LV_MV_OUTPUT_CTL_SHIFT);
+ if (ret < 0)
+ return ret;
+ }
+
/* Set the right pull (no pull) */
ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_PULL_CTL,
REG_DIG_PULL_NO_PU);
@@ -118,19 +152,30 @@ static int qcom_gpio_get_function(struct udevice *dev, unsigned offset)
uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
int reg;
- /* Set the output value of the gpio */
reg = pmic_reg_read(dev->parent, gpio_base + REG_CTL);
if (reg < 0)
return reg;
- switch (reg & REG_CTL_MODE_MASK) {
- case REG_CTL_MODE_INPUT:
- return GPIOF_INPUT;
- case REG_CTL_MODE_INOUT: /* Fallthrough */
- case REG_CTL_MODE_OUTPUT:
- return GPIOF_OUTPUT;
- default:
- return GPIOF_UNKNOWN;
+ if (priv->lv_mv_type) {
+ switch (reg & REG_CTL_LV_MV_MODE_MASK) {
+ case REG_CTL_LV_MV_MODE_INPUT:
+ return GPIOF_INPUT;
+ case REG_CTL_LV_MV_MODE_INOUT: /* Fallthrough */
+ case REG_CTL_LV_MV_MODE_OUTPUT:
+ return GPIOF_OUTPUT;
+ default:
+ return GPIOF_UNKNOWN;
+ }
+ } else {
+ switch (reg & REG_CTL_MODE_MASK) {
+ case REG_CTL_MODE_INPUT:
+ return GPIOF_INPUT;
+ case REG_CTL_MODE_INOUT: /* Fallthrough */
+ case REG_CTL_MODE_OUTPUT:
+ return GPIOF_OUTPUT;
+ default:
+ return GPIOF_UNKNOWN;
+ }
}
}
@@ -154,8 +199,14 @@ static int qcom_gpio_set_value(struct udevice *dev, unsigned offset,
uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
/* Set the output value of the gpio */
- return pmic_clrsetbits(dev->parent, gpio_base + REG_CTL,
- REG_CTL_OUTPUT_MASK, !!value);
+ if (priv->lv_mv_type)
+ return pmic_clrsetbits(dev->parent,
+ gpio_base + REG_LV_MV_OUTPUT_CTL,
+ REG_LV_MV_OUTPUT_CTL_MASK,
+ !!value << REG_LV_MV_OUTPUT_CTL_SHIFT);
+ else
+ return pmic_clrsetbits(dev->parent, gpio_base + REG_CTL,
+ REG_CTL_OUTPUT_MASK, !!value);
}
static const struct dm_gpio_ops qcom_gpio_ops = {
@@ -177,13 +228,17 @@ static int qcom_gpio_probe(struct udevice *dev)
/* Do a sanity check */
reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
- if (reg != 0x10)
+ if (reg != REG_TYPE_VAL)
return log_msg_ret("bad type", -ENXIO);
reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
- if (reg != 0x5 && reg != 0x1)
+ if (reg != REG_SUBTYPE_GPIO_4CH && reg != REG_SUBTYPE_GPIOC_4CH &&
+ reg != REG_SUBTYPE_GPIO_LV && reg != REG_SUBTYPE_GPIO_MV)
return log_msg_ret("bad subtype", -ENXIO);
+ priv->lv_mv_type = reg == REG_SUBTYPE_GPIO_LV ||
+ reg == REG_SUBTYPE_GPIO_MV;
+
return 0;
}
@@ -203,6 +258,7 @@ static const struct udevice_id qcom_gpio_ids[] = {
{ .compatible = "qcom,pm8916-gpio" },
{ .compatible = "qcom,pm8994-gpio" }, /* 22 GPIO's */
{ .compatible = "qcom,pm8998-gpio" },
+ { .compatible = "qcom,pms405-gpio" },
{ }
};
GPIO LV (low voltage)/MV (medium voltage) subtypes have different features and register mappings than 4CH/8CH subtypes. Add support for LV and MV subtypes. With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible which requires support for GPIO MV subtype. Signed-off-by: Sumit Garg <sumit.garg@linaro.org> --- drivers/gpio/qcom_pmic_gpio.c | 96 +++++++++++++++++++++++++++-------- 1 file changed, 76 insertions(+), 20 deletions(-)