diff mbox series

[v3,3/3] Bluetooth:btsub:Ignore zero length of USB packets on ALT 6 for specific chip

Message ID 20220929114426.4413-4-hildawu@realtek.com
State Superseded
Headers show
Series Bluetooth: Add btrealtek data struct and improve SCO sound quality of RTK chips | expand

Commit Message

Hilda Wu Sept. 29, 2022, 11:44 a.m. UTC
From: Hilda Wu <hildawu@realtek.com>

For USB ALT 6 settings some Realtek chips need to transmit mSBC data
continuously without the zero length of USB packets.
In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior.
Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific
chip model for the behavior.

Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
---
Changes in V3
 - For ignore_usb_alt6_packet_flow, manage the common flag by the vendor private flag.
---
---
 drivers/bluetooth/btrtl.c |  7 +++++++
 drivers/bluetooth/btusb.c | 25 +++++++++++++++++++++++--
 2 files changed, 30 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
index 272f90621a10..7159427c530e 100644
--- a/drivers/bluetooth/btrtl.c
+++ b/drivers/bluetooth/btrtl.c
@@ -781,6 +781,13 @@  void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
 	case CHIP_ID_8852C:
 		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
 		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
+
+		/* RTL8852C needs to transmit mSBC data continuously without
+		 * the zero length of USB packets for the ALT 6 supported chips
+		 */
+		if (btrtl_dev->project_id == CHIP_ID_8852C)
+			btrealtek_set_flag(hdev, REALTEK_ALT6_CONTINUOUS_TX_CHIP);
+
 		hci_set_aosp_capable(hdev);
 		break;
 	default:
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 7583059e3b2c..076cfee1ad57 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -626,6 +626,7 @@  static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
 #define BTUSB_TX_WAIT_VND_EVT	13
 #define BTUSB_WAKEUP_AUTOSUSPEND	14
 #define BTUSB_USE_ALT3_FOR_WBS	15
+#define BTUSB_ALT6_CONTINUOUS_TX	16
 
 struct btusb_data {
 	struct hci_dev       *hdev;
@@ -1271,11 +1272,17 @@  static void btusb_isoc_complete(struct urb *urb)
 static inline void __fill_isoc_descriptor_msbc(struct urb *urb, int len,
 					       int mtu, struct btusb_data *data)
 {
-	int i, offset = 0;
+	int i = 0, offset = 0;
 	unsigned int interval;
 
 	BT_DBG("len %d mtu %d", len, mtu);
 
+	/* For mSBC ALT 6 settings some chips need to transmit the data
+	 * continuously without the zero length of USB packets.
+	 */
+	if (test_bit(BTUSB_ALT6_CONTINUOUS_TX, &data->flags))
+		goto ignore_usb_alt6_packet_flow;
+
 	/* For mSBC ALT 6 setting the host will send the packet at continuous
 	 * flow. As per core spec 5, vol 4, part B, table 2.1. For ALT setting
 	 * 6 the HCI PACKET INTERVAL should be 7.5ms for every usb packets.
@@ -1295,6 +1302,7 @@  static inline void __fill_isoc_descriptor_msbc(struct urb *urb, int len,
 		urb->iso_frame_desc[i].length = offset;
 	}
 
+ignore_usb_alt6_packet_flow:
 	if (len && i < BTUSB_MAX_ISOC_FRAMES) {
 		urb->iso_frame_desc[i].offset = offset;
 		urb->iso_frame_desc[i].length = len;
@@ -2381,6 +2389,19 @@  static int btusb_recv_isoc_realtek(struct btusb_data *data, void *buffer,
 	return err;
 }
 
+static int btusb_setup_realtek(struct hci_dev *hdev)
+{
+	struct btusb_data *data = hci_get_drvdata(hdev);
+	int ret;
+
+	ret = btrtl_setup_realtek(hdev);
+
+	if (btrealtek_test_flag(data->hdev, REALTEK_ALT6_CONTINUOUS_TX_CHIP))
+		set_bit(BTUSB_ALT6_CONTINUOUS_TX, &data->flags);
+
+	return ret;
+}
+
 /* UHW CR mapping */
 #define MTK_BT_MISC		0x70002510
 #define MTK_BT_SUBSYS_RST	0x70002610
@@ -3983,7 +4004,7 @@  static int btusb_probe(struct usb_interface *intf,
 
 	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
 	    (id->driver_info & BTUSB_REALTEK)) {
-		hdev->setup = btrtl_setup_realtek;
+		hdev->setup = btusb_setup_realtek;
 		hdev->shutdown = btrtl_shutdown_realtek;
 		hdev->cmd_timeout = btusb_rtl_cmd_timeout;